Operation Manual

ManualsBrandsCateye ManualsCarCC-GL11 Stealth evo

How to install the

unit on your bicycle

Setting up the

computer

How to use the

computer

Others

Changing the

computer con-

ﬁguration

Uploading the mea-

surement data

Setup of your

Introduction

CYCLOCOMPUTER CC-GL11

Features of this unit

Measurement method

This unit is a cyclocomputer, having a GPS and acceleration sensor built-in, which can per-

form measurement by receiving GPS signal, without speed sensor.

Recording and viewing the trip route

Position information from GPS is recorded with measurement data during measurement.

The measurement data such as your route and altitude can be viewed as a trip on a map on

the site, by loading them into the dedicated software application “CATEYE Sync™” on your

PC, and then uploading to the special website “CATEYE Atlas™”.

”CATEYE Atlas™” can be used as a database for your cycling life, where you can store the

trips measured using this unit or CATEYE INOU, a trip recorder with camera.

Icons used in this manual

• This manual indicates computer button operations as shown below.

Press the button

MODE

Press the MODE button

Press the button

for 2 seconds

MODE

Press the MODE button

for 2 seconds

Press the MENU button

• For explanatory purposes, in this manual red text/icons on the computer screen represent

ﬂashing items.

Before using the computer, please thoroughly read this manual

and keep it for future reference.

* This PDF contains a link to YouTube.

When you click on the button “Watch a video”, a message regarding security

appears.

Click the “Allow” to open a browser and play the video.

* YouTube videos and instruction manuals related to this product are subject to

change without notice.

For the latest edition of the instruction manual (PDF), visit the ofﬁcial CatEye

website.

* This manual has been prepared on the assumption that the user has sufﬁcient

basic knowledge, including operation and terminology of PCs (Windows / Mac).

Instruction manual

ENG

This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation

is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

L’appareil est conforme à la réglementation FCC, section 15 et Industrie Canada RSS standard exempts de licence (s).

Son utilisation est soumise à deux conditions :

1. L’appareil ne doit pas provoquer d’interférences nuisibles, et

L’appareil doit supporter les interférences reçues, y compris les interférences empêchant son fonctionnement correct.

Modiﬁcations

The FCC requires the user to be notiﬁed that any changes or modiﬁcations made to this device that are not expressly

approved by CatEye Co., Ltd. may void the user ’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip-

ment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or

relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a

circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

066601231

Summary of content (33 pages)

PAGE 1
Introduction Features of this unit Measurement method CYCLOCOMPUTER CC-GL11 ENG Position information from GPS is recorded with measurement data during measurement. The measurement data such as your route and altitude can be viewed as a trip on a map on the site, by loading them into the dedicated software application “CATEYE Sync™” on your PC, and then uploading to the special website “CATEYE Atlas™”.
PAGE 2
Warning / Caution GPS (Global Positioning System) is a system to identify the current position on the earth by receiving highly precise positional information sent from a satellite. Receiving the GPS signal Recharge the battery for first time use or after long period of storage The voltage of the battery may drop during a long period of storage due to standby current. Always fully charge the battery before use.
PAGE 3
Computer Icon AC button Used for formatting and restarting operations. Contact (Light up) Remaining battery capacity is large. Remaining battery capacity is small. (Flash) Switches the selected function and setting items. Pace arrow Indicates if the current speed is faster or slower than the average speed. ( Faster, Slower) Accessories Selected data icon Bracket Dial Bracket rubber pad Bracket band Dot display GPS signal is weak.
PAGE 4
Click the button, then a browser will open and a video will be played back. Cut the excess length of the band using scissors. Caution: Round off the cut edge of the bracket strap to prevent injury. How to install the unit on your bicycle Watch video (YouTube) Introduction How to install the unit on your bicycle * To mount the bracket to an aero-shaped handlebar or larger stem, use the optional nylon ties bracket.
PAGE 5
Power ON/OFF Perform the following formatting operation, when you use the unit for the first time or restore the unit to the condition before shipment. Caution: All data are deleted, and the computer is reset to the factory default. (Press & hold) Computer Caution: Do not set wet computer to the cradle, for example after ride in the rain. It may cause short circuit and damage the computer or the data.
PAGE 6
Introduction Time zone list 3 Select the time zone City code Register the setting (Press & hold) Switch the display MODE MODE -10:00 -09:00 +08:00 -07:00 -06:00 -05:00 -04:00 -03:00 -02:00 -01:00 -00:00 London 0 DRW Darwin +9.5 PAR Paris +1 SYD Sydney +10 ATH Athens +2 NOU Noumea +11 MOW Moscow +3 WLG Wellington +12 THR Tehran +3.5 PPG Pago Pago -11 DXB Dubai +4 HNL Honolulu -10 KBL Kabul +4.
PAGE 7
Introduction 4 Select the daylight saving time Setting How to install the unit on your bicycle You can set the daylight saving time when you are on Daylight Saving Time. Select ON or OFF. Description ON Displays 1 hour faster than regular clock. OFF Displays in regular clock. Setting up the computer Daylight saving time icon Register the setting (Press & hold) ON ↔ OFF MODE MODE How to use the computer * Change ON/OFF according to the period of daylight saving time.
PAGE 8
Changed automatically GPS search screen Power OFF Clock 0:00 – 23:59 [AM1:00 – PM12:59] (Press & hold) MODE * STOP is displayed when GPS is not received. Measurement screen Standby screen No operation for 10 minutes No operation for 10 minutes Measurement stops GO Current speed 0.0 (3.0) – 105.9 km/h [0.0 (2.0) – 65.9 m/h] Measurement starts or Selected data STOP * When GPS is not received, measurement will not start even if the button is pressed and GO is displayed.
PAGE 9
Clock 0:00 – 23:59 [AM1:00 – PM12:59] (Press & hold) MODE * STOP is displayed when GPS is not received. To be changed according to the GPS signal receiving status. Standby screen No operation for 10 minutes GO Measurement starts Uploading the measurement data No operation for 10 minutes Measurement stops Current speed 0.0 (3.0) – 105.9 km/h [0.0 (2.0) – 65.
PAGE 10
Starting/Stopping measurement 4 Press the Caution: Measurement requires an environment in which GPS signals can be received. * For details regarding each screen, see “Screen flow” (page 8). button for 5 Press and hold the The unit turns off. * If the unit is turned off without stopping measurement, it will start up in measurement mode when it is turned back on. GO button STOP changes to GO on the measurement screen, and measurement starts.
PAGE 11
MODE Elapsed Time 0:00’ 00” – 9:59’ 59” Dst MODE Trip Distance 0.00 – 999.99 km [mile] PM 6:59 PM 7:00 – AM 5:59 AM 6:00 Trip Distance-2 0.00 – 999.99 / 1000.0 – 9999.9 km [mile] How to use the computer A backlight is turned on automatically MODE * The night-time can be set to your needs. For details, see “Night-time setting” (when using CATEYE Sync™: page 23, when using the computer alone: page 27). * As default, it is set to 6:00 PM to 7:00 AM. Setup of your PC Av Average Speed 0.0 – 105.
PAGE 12
Introduction Holding down the MODE button with the measurement screen displayed resets the measurement data to 0 (resetting operation). All the measurement data up to that time are generated as trip data. You can view measurement results and store trip records, by uploading the trip data to the special website “CATEYE Atlas™” via the dedicated software application “CATEYE Sync™”. Resetting operation MODE MODE 2 day Trip days Trip data for the 1st day are generated.
PAGE 13
Introduction Setup of your PC At first, access the special website CATEYE Atlas™ to register as a member. Then, install CATEYE Sync™ to your PC (Windows/Mac). You can upload the trip data measured with this unit to CATEYE Atlas™, STRAVA™, TrainingPeaks™ and others, or change the computer configuration using your PC. How to install the unit on your bicycle Caution: Use the PC with an Internet access environment to access CATEYE Atlas™ or download CATEYE Sync™.
PAGE 14
Enter correctly the e-mail address and password you registered at CATEYE Atlas™. How to install the unit on your bicycle After installing CATEYE Sync™, configure the login setting for CATEYE Atlas™. * When uploading the trip data only to STRAVA™ or TrainingPeaks™, the following setting is not required. 3 Click on [Account setting] and enter your e-mail address and password Introduction Setting CATEYE Sync™ 1 Start CATEYE Sync™ Double-click on the shortcut [CATEYE Sync™] to start CATEYE Sync™.
PAGE 15
The trip data generated by the resetting operation can be uploaded to the special website CATEYE Atlas™ or other services (STRAVA™ and others) in the following procedure. that “STEALTH” is selected under Device, and click [Download 4 Check All Activities & View Data List] The trip data is downloaded from the computer to your PC, and the data list screen appears.
PAGE 16
When the upload is complete, the sites to which the data was uploaded are indicated in the “Status” column and links to the trip are displayed in the adjacent column. Setting up the computer Uploaded trip data Service sites to which data was uploaded Links to sites * Clicking the link launches your browser and displays the uploaded trip. Clear the check box for any unnecessary trip data, and then click the upload button for the service site you want to upload the data to.
PAGE 17
You can export the trip data saved in CATEYE Sync™, and create a file. Introduction Exporting the trip data 3 Select the destination to save, and then click on [Open] The file will be exported to the destination specified. How to install the unit on your bicycle 1 Check any trip data on the data list screen, and then click on [Export] A dialog for selecting the file format appears.
PAGE 18
Introduction 3 Select the file you want to load, and then click on [Open] How to install the unit on your bicycle Importing the data of such as e-Train Data™ to CATEYE Sync™ The measurement data loaded into e-Train Data™ can be used with CATEYE Atlas™ and other services (STRAVA™ etc.) by importing it to CATEYE Sync™. 1 Export the measurement data from e-Train Data™, and prepare a file 2 Click on [Import] on the top screen A window for selecting the file appears.
PAGE 19
Introduction Trip data How to install the unit on your bicycle Data contained in the trip data Date and clock (date/time when the measurement started) Elapsed time Setting up the computer Data recorded at the record interval specified • Location information • Trip distance • Altitude • Current speed How to use the computer Record interval and capacity limit This unit records data at the specified interval.
PAGE 20
Introduction 4 Click on the trip uploaded A map with the trip route with ride data shown. How to install the unit on your bicycle Reviewing, editing and sharing the trip (What you can do with CATEYE Atlas™) You can share the trip with your friends and other users, by editing the trip information uploaded to CATEYE Atlas™. 1 Access CATEYE Atlas™ Access the website “CATEYE Atlas™” from your browser (http://www.cateyeatlas.com).
PAGE 21
Deleting the GPS point You can delete particular GPS points on the route. How to install the unit on your bicycle Select the disclosure setting. • Private : Can be viewed only with your account. • Public : All users can view. • Friends only : Only your friends can view. Introduction 6 Select the privacy setting 1 Click on [Delete GPS point] from the trip information editing screen. The trip route appears on the map.
PAGE 22
Introduction Exporting to a GPX fil How to install the unit on your bicycle Export a general-purpose GPS data file from the trip. This can be used with other services, including Google Earth™. 1 Click on [GPX export] on the trip information editing screen. A confirmation message appears. Setting up the computer How to use the computer Setup of your PC 2 Click on [Export]. A GPX file is downloaded.
PAGE 23
4 Click on [Settings] The setting screen appears. How to install the unit on your bicycle You can change the computer configuration in two ways. • Changing the setting with CATEYE Sync™ (below on this page) You can change the configuration easily from your PC application, with the computer connected to your PC with the cradle. Introduction Changing the computer configuration • Changing the settings of the computer alone (page 25). This can be used when changing the setting with not using a PC.
PAGE 24
Setting items Description Tire circumferThis is not used with this unit. ence How to install the unit on your bicycle Before changing the settings, click on [Read] to load the settings of the computer. Introduction 6 Click on [STEALTH] to change the settings Read the current settings of the computer. Change the settings according to the following procedure. Time zone Description Clock display format Select the city code nearest from your current location.
PAGE 25
From “Selecting the speed unit” (page 28) MENU Clock setting (on the right of this page) MODE Night-time setting (page 27) MODE Setting the record interval (page 27) Change the settings of the time zone, daylight saving time, and the clock display format. * With this unit, it is not necessary to set the clock/date, since they are synchronized after receiving GPS signal. MODE Changing the settings Time zone list Select the code for the city nearest from your current location.
PAGE 26
Time zone list City code Example: Change the time zone LON NYC (New York) Previous setting TYO (Tokyo) Register the setting Every menu top screen MENU The time zone is changed from NYC (New York) to TYO (Tokyo) of the previous setting. Change the time zone again Current setting TYO (Tokyo) Shortcut Register the setting MENU 0 DRW Darwin +9.5 PAR Paris +1 SYD Sydney +10 ATH Athens +2 NOU Noumea +11 MOW Moscow +3 WLG Wellington +12 THR Tehran +3.
PAGE 27
From “Night-time setting” Setting the record interval Set the time when the backlight lights up. * When you do not want to turn on the backlight throughout the day, set the start time and end time to the same hour. Set the second-scale interval to record the measurement data. * The maximum recording time / maximum time for one trip that can be recorded in the computer depends on the selected interval.
PAGE 28
From “Entering the total distance” Setting the middle display Selecting the speed unit Select the middle display of the measurement screen. Select the speed unit (km/h or m/h).
PAGE 29
Introduction When the operation is unstable How to install the unit on your bicycle When the computer displays incorrectly, perform the restarting operation to stabilize the operation. * Performing the restarting operation deletes any records under measurement. * We recommend that you perform the resetting operation to generate the trip data, before performing the restarting operation. Restarting operation Setting up the computer Press the AC button on the back of the computer.
PAGE 30
Introduction Troubleshooting The following troubles are not due to failure. See also “FAQ” in CATEYE Atlas™ (web) (http://www.cateyeatlas.com/qa/). The power is turned off while riding. Measurement cannot be performed – Remaining battery capacity is nearly zero. Charge the computer according to the procedure in “How to charge” (page 5). – The power is turned off automatically in 10 minutes without GPS signal received. (Auto power off) The measurement data is wrong.
PAGE 31
Trouble Remedy The backlight lights up Is the start time of the during the daytime. night-time set correctly? Bracket kit 1600280N Bracket band 1602193 Bracket 1603790 Cradle (IF-CC01) How to use the computer For information on how to set the start time, see “Night-time setting” (when using CATEYE Sync™: page 23, when using the computer alone: page 27).
PAGE 32
Upper display Current speed Tm Elapsed Time 0:00’00” – 9:59’59” Dst Trip Distance 0.00 – 999.99 km [mile] Lower display 0.00 – 999.99 / 1000.0 – 9999.9 km [mile] 0.0 – 105.9 km/h [0.0 – 65.9 m/h] Mx Maximum Speed 0.0 (3.0) – 105.9 km/h [0.0 (2.0) – 65.9 m/h] ALT Altitude -500 – 9999 m [-1640 – 29600 ft] Odo Total Distance 0.0 – 9999.9 / 10000 – 99999 km [mile] Approx. 5 hours (USB2.0) Standard operating time Approx.
PAGE 33
Introduction Limited warranty How to install the unit on your bicycle 2-year Warranty: Computer only (Deterioration of the battery is excluded.) Setting up the computer CatEye cycle computers are warranted to be free of defects from materials and workmanship for a period of two years from original purchase. If the product fails to work due to normal use, CatEye will repair or replace the defect at no charge. Service must be performed by CatEye or an authorized retailer.