User's Manual

ManualsBrandsCATEYE ManualsElectronicsWheel Revolution Transmitter

TIRE SIZE L(cm) TIRE SIZE L(cm)

24 x 1 1753

24 x 3/4 Tubular 1785

24 x 1-1/8 Tubular 1795

24 x 1-1/4 1905

24 x 1.75 1890

24 x 2.00 1925

24 x 2.125 1965

26 x 1(559mm) 1913

26 x 1(650c) 1952

26 x 1.25 1953

26 x 1-1/8 Tubular 1970

26 x 1-3/8 2068

26 x 1-1/2 2100

26 x 1.40 2005

26 x 1.50 1985

26 x 1.75 2030

26 x 1.95 2050

26 x 2.00 2055

26 x 2.1 2068

26 x 2.125 2070

26 x 2.35 2083

27 x 1 2145

27 x 1-1/8 2155

27 x 1-1/4 2161

27 x 1-3/8 2169

650 x 35A 2090

650 x 38A 2125

650 x 38B 2105

700 x 18C 2070

700 x 19C 2090

700 x 20C 2086

700 x 23C 2096

700 x 25C 2105

700 x 28C 2136

700 x 30C 2170

700 x 32C 2155

700C Tubular 2130

700 x 35C 2168

700 x 38C 2180

700 x 44C 2224

0687303

US. PAT. NO.4633216,4636769,4642606,5089775,5236759 & Design Patented.

Setting Values Cross Reference Table

(The tire size is marked on both sides of the tire.)

Specifications

Controller ..................................... 4-bit 1-chip Microcomputer (Crystal Controlled Oscillator)

Display .......................................... Liquid Crystal Display

Sensor .......................................... No Contakt Magnetic Sensor

Cordless Système .....................................

Directional electromagnetic induction

Operating Temperature Range/ .................

0°C - 40°C(32°F - 104°F)

LIMITED WARRANTY

2-Year Warranty: Only Main Unit/Sensor

If trouble occurs during normal use, the part is repaired or replaced free of charge. The service must be

performed by CATEYE Co., Ltd.. and the product needs service must be returned to CATEYE Co., Ltd.

directly by purchaser. When returning the product for CATEYE warranty service, pack it very carefully,

and enclose the warranty certificate and instructions for repair. Please make sure to write or type your

name and address clearly on the warranty certificate, so that the product can be shipped back to you as

soon as the necessary repair/adjustment is completed. Insurance, handling and transportation charges

to our service shall be borne by person desiring service.

Address for service

.,LTD.

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan

Attn.: CATEYE Customer Service Section

Service & Research Address for United States Consumers:

CATEYE Service & Research Center

1705 14th St. 115 Boulder, CO 80302

Phone: 303-443-4595 Toll Free: 800-5CATEYE

Fax: 303-473-0006 e-mail: CatEyeUSA@aol.com

CYCLOCOMPUTER

Model CC-CL200

COIN

sensor

OPERATION FEATURES

Two buttons are provided on the top of the main unit and two on the bottom.

These buttons are used as follows:

•Mode Button (top left button)

Whenever this button is pressed, the mode display changes in the order

shown in fig.1, and the data is displayed on the sub-display. Note: If this

button is kept pressed for more than 2 seconds, display appears.

•Start/Stop Button (top right button)

Measurement of trip distance, elapsed time and average speed is started or

stopped when the start/stop button is pressed. Whenever this button is

pressed, start and stop are repeated. During measurement the speed scale

symbol blinks.

Note: This button does not function if the auto mode function is set to ON

[Refer to the explanation of the Auto (Automatic Start/Stop) Function below].

•Set Button (bottom left button)

• To set the wheel circumference:

Stop the measurement in the (O) mode, then press the SET button.

• To set the 24-hour clock time:

Stop the measurement in ( ) mode, then press the SET button.

• To set auto mode to ON or OFF:

Select the (T),(A) or (D) mode, then press the SET button.

•AC (All Clear) Button (bottom right button)

When this button is pressed, all the data stored in memory is cleared.

After all displays illuminate, the "mile/h" symbol illuminates. This button should

be pressed only after replacing the battery or when irregular display of infor-

mation occurs due to static electricity,etc. Once this button is pressed and all

memory is erased, it will be necessary to set the wheel circumference, time,

etc. again. (refer to Main Unit Preparation)

Reset Operation: (Fig.2)

Press left button to select any mode except total distance (O) and press left

and right buttons together. Stored data of trip distance (D), elapsed time (T),

average speed (A) and maximum speed (M) are all reset to zero. (In the total

distance display mode, the current wheel circumference (A) or (B) is shown.)

MAIN UNIT PREPARATION

User must make the following setting according to instructions before

the cyclocomputer can be used properly.

1. How to measure the exact Wheel Circumference (L)(Fig.3)

First, adjust tire pressure and then put a mark on the tire tread and the ground

simultaneously. Then ride the bike one full wheel revolution. Mark the ground

at the end of one revolution and then measure the distance between the two

marks. This measure is your actual wheel circumference. Or, the "Setting Val-

ues Cross Reference Table" can help you to find out an approximate wheel

circumference according to tire size.

2. Setting the Speed Scale (Fig.4)

When the AC button is pressed and all displays illuminate then the "mile/h"

appears as shown in fig.4. "km/h" and "mile/h" are displayed alternatively each

time the right button is pressed. Select any speed scale as desired and press

SET button to complete the setting.

3. Setting the Wheel Circumference (Fig.5.6)

This cyclocomputer is able to memorize two different wheel circumferences.

One main unit can be used on two bicycles subject to buy another set of

bracket and sensor.

Two wheel circumferences, (A) 2155mm and (B) 2030mm, have been set be-

fore the cyclocomputer left our factory. The (A) wheel circumference 2155mm

(standard for 27 inch tire) will blink as shown in fig.5. If you want to enter

2155mm and 2030mm, simply press the SET button. If you want to change,

press either the right button to increase or left button to decrease the number.

To change the number rapidly keep the button pressed. Once you reach the

setting you want, press the SET button. If you want to set a second circumfer-

ence, press the left and right buttons together before pressing the SET button.

The wheel circumference 2030mm is displayed and blinks(fig.6). Set to a de-

sired wheel circumference in the same manner as the first circumference set-

ting and press SET button to complete the setting.

4. Selecting one of the two Wheel Circumference (Fig.7)

Set the Auto Mode to ON. (Refer to the explanation of Auto Mode function.)

While keeping the right button pressed , press the SET button. The first wheel

circumference measurement will be displayed for a few seconds, then the sec-

ond setting will appear.

5. How to reset the Wheel Circumference

Select the (O) mode and stop the measurement. Press SET button and the

already set wheel circumference will blink on the sub-display. Refer to '3.Set-

ting the wheel circumference' to complete the setting.

Setting the 24-hour Clock (Fig.8)

Press left button for more than 2 seconds to select the 24-hour clock display.

Stop the measurement by pressing the right button. Press SET button and the

minute display will start to blink. Press right button to select a minute time

ahead of the current time by 1 to 2 minutes. Next press left button and the hour

will blink. Press right button to set to current hour time. Press SET button to

complete the setting.

MOUNTING TO BIKE

If necessary, use either the 1mm or 2mm thick rubber pads according to the

handlebar diameter. Mount the bracket as shown in fig.9.

• Slide the main unit onto the bracket from front until it clicks into position. To

remove the main unit, pull it forward while depressing the lever on bracket

(fig.10).

How to Mount the Sensor on the Right Front Fork Leg.(fig.11)

Mount the sensor in the highest possible position on the right front fork leg.

Adjust the position, clearance and direction as follows:

(1) Insert the band B into the slit of the band A, and put the rubber pad inside

of the band A (fig. 12). Adjust the length of the bands in order that the

screw-fastening part of the bands is parallel when mounted to the fork (fig.

13). * To pull out the band B from band A, tug strongly.

(2) Mount the adjusted bands to fork along with the sensor, by temporarily

tightening the screw (fig. 14).If the space between front fork and spoke of

your bike is big, use the spacer and long screw as in the fig.15, so that the

clearance between sensor and magnet will be approx. 5mm.

(3) Use a coin to install the magnet securely to the spoke so that it face the

sensor zone.(fig.16 & 17)

(4) A 5mm clearance shall be kept between the sensor and magnet(fig.18).

Then align the magnet with sensor zone (fig.16). Meanwhile, the sensor

shall aim at the main unit indicated by the triangle marked on the sensor.

Then tighten the screw to secure the sensor in position. Cut the excess

sensor band B with scissors or the like.

Check points for sensor mounting:

1.Keep a 5mm clearance between the sensor and magnet.

2.The magnet surface shall align to the sensor zone.

3.The triangle mark on the sensor shall aim at the main unit.

TEST

Mount the main unit on the bracket. If current speed doesn't appear on the

main display, press either left or right button to release the unit from the power

saving mode. Then spin the front wheel to make sure the wheel sensor pulse

symbol flickers. If it does not flicker, adjust the position of sensor until it flickers

normally. The mounting is completed and the cyclocomputer is operational.

THE CORDLESS SYSTEM

The sensor picks up wheel revolution signal and transmits the signal to the

receiver in the main unit. The main unit receives, calculates and displays the

data. The approximate service hour of batteries is as follows:

The main unit (receiver): --- Approx. 2 years (average 1 hour's use per day)

The sensor (transmitter): ------- Total distance of approx. 10,000 miles (16,000 km)

Note: To prevent external signal interference, the sensor signal reception

range is restricted. For best performance, the triangle mark

on the sensor shall

aim at the direction to the main unit. The distance between the sensor and

main unit must be kept within 45 cm. The signal reception range may shorten

as a result of low ambient temperature or lowered battery power. It is advisable

to replace the sensor battery before it fails. The battery service hours quoted

above is the average for a 45cm distance between the sensor and main unit.

• The cordless system may be interfered with in the following situation, so that

main unit may display false data.

1. Riding near railroad crossings and trains.

2. Riding in places where intensive electromagnetic wave or field exist,

such as TV transmission station and radar installations.

3. When two bicycles carrying similar cyclocomputers are ridden side by

side.

REPLACING THE BATTERIES

Batteries are already loaded in the main unit and the sensor.

How to replace battery in Main Unit (Fig.20)

Open the battery cover on the back and insert a new CR2032 (lithium) with the

(+) pole upward, while pressing the side of the battery against the contact.

Press AC button to erase all stored data and then redo the settings.

How to replace battery in Sensor (Fig.21)

Take off the sensor from the bicycle. Open the battery cover on the back and

insert a new CR2032 (lithium) with the (+) pole upward, while pressing the side

of the battery against the contact. Mount the sensor back to the bicycle and

adjust to relative position, clearance and direction.

INSTRUCTION MANUAL

bracket

slide

front

front fork

magnet

sensor band B

front fork

screw

sensor zone

triangle mark

magnet

spoke

magnet

CR2032

OPEN

CR2032

sensor

sensor rubber pad

sensor

bracket rubber pad

Fig.9

Fig.10

Fig.11

Fig.12

sensor band A

Fig.14

Fig.15

Fig.16

Fig.18

Fig.19

OPEN

Fig.20

sensor zone

spoke

sensor rubber

pad

sensor band A

Fig.13

parallel

lever

Reset

about 5mm

POWER SAVING FUNCTION

When the main unit is left without receiving any signal for one hour, the power will

be turned off automatically. Resulting in SLEEP state in which only the 24-hour

clock displays. The main unit can not receive any signal in this state. Press left or

right button to restore signal reception.

Note: Remember to restore signal reception before every journey.

MAINTENANCE/PRECAUTIONS

• Do not leave the main unit exposed to direct sunlight when the unit is not in use. Do not disassemble

the main unit.

• Don't pay too much attention to your computer's functions while riding! Keep your eyes on the road

and give due consideration to traffic safety.

• Check the relative position of magnet and sensor periodically.

• For cleaning, use neutral detergent on soft cloth, and wipe off later with dry cloth. Do not apply paint

thinner, benzine, or alcohol, which may damage on the surface.

TROUBLE SHOOTING

No display. ------------------------------------------------------ Replace the main unit battery with new one.

Incorrect data appears. -------------------------------------- Execute "All Clear" operation.

Figures do not appear on the main display ------------- Cancel the power saving function.

Current speed does not appear. --------------------------- Check the sensor position and direction.

Speed is not displayed when riding with high speed or at low temperature.

--------------------------------------------------------------------- Check the sensor position and direction.

--------------------------------------------------------------------- Has the battery worn out?

Even when the right button is pressed, the cyclocomputer does not operate.

--------------------------------------------------------------------- Set the auto mode to OFF.

The entire liquid crystal screen is dark and unusual display is seen where it should not be.

--------------------------------------------------------------------- It returns to normal state if left in the shade.

Display response is slow. ----------------------------------- It returns to normal state when temperature rises.

SPECIFICATIONS

Applicable Cycle Sizes 10 mm - 2,999 mm(Initial value:A:2155 mm B:2030 mm)

Power Supply Main unit: ------------------------------------ Lithium Battery (CR2032)x1/approx.,2years

Sensor with transmitter: ------------------ Lithium Battery (CR2032)x1/approx.1,000miles

Dimension / Weight 2"x 1-13/10"x 29/32" / 1,2 oz (29 g)

* The specifications and design are subject to change without notice.

AUTO (AUTOMATIC START/STOP) FUNCTION

The Cordless 2 is equipped with a selective auto function allowing automatic start

or stop of measurement without using the right button.

How to Set On/Off the Auto Function

Select (T), (D) or (A) to sub-display and then press SET button. The

symbol

will display when auto function is set ON. Repeat to set OFF the auto function.

Note: In SLEEP state, auto start will not function. Press left or right button to restore

signal reception first. (Refer to Power Saving Function)

S Current Speed 0.0(3.0) to 65.9 miles/hr ±0.3mile/h

This is always displayed on the main display and updated once a second.

O Total Distance 0.0 to 99,999 miles ±0.1mile

This is continuously measured until battery wears down or all clear operation is

done. At 10,000 miles(km), it returns to zero and counting begins anew.

D Trip Distance 0.00 to 999.99 miles 0.01mile

The trip distance from start to current point is displayed. With Reset operation, it

returns to zero.

T Elapsed Time 0:00'00" to 9:59'59" ±0.003%

Elapsed time is measured from start to current point, in units of hours, minutes and

seconds. At 10 hours, it returns to zero and counting begins anew. With Reset

operation, it returns to zero.

A Average Speed 0.0 to 65.9 miles/hr ±0.3mile/h

The average speed from start to current point is displayed within 27 hours 46 min-

utes 39 seconds (99,999 seconds) or 999.99 miles (km). If either is exceeded, (.E)

is displayed and calculation ceases.

M Maximum Speed 0.0 (3.0) to 65.9 miles/hr ±0.3mile/h

With Reset operation, it returns to zero and counting begins anew.

24 hr. Clock Time 0:00´ to 23:59´ ±0.003%

The current time is displayed by a 24-hour clock.

DISPLAY FUNCTIONS

H. Sub-Display

(Selected function)

I. Start/Stop Button

J. Battery Case Cover

K. Set Button

L. AC Button

A. Main Display(Speed)

B. Wheel Circumference Mark

C. Mode Symbol

D. Mode Button

E. Wheel Sensor Pulse Symbol

F. Speed Scale Symbol

G. Auto Mode Symbol

1. Bracket

2. Sensor(Transmitter)

3. Sensor Band A

4. Sensor Band B

5. Magnet

6. Bracket Rubber Pad (1mm,2mm)

Fig.2

Fig.4

Fig.5

Fig.6

Fig.8

Fig.7

Fig.1

Fig.3

7. Sensor Rubber Pad

8. Screw

9. Long Screw

10. Spacer

spacer

long screw

Fig.21

Fig.17

contact

#169-6690

Parts Kit

#169-6660

Bracket Kit

#169-6670

Cordless Sensor

#169-6680

Universal Sensor Band

#169-6667

Center Mount Bracket Kit

#169-6669

Stem Mount Bracket Kit

#169-6070 #166-5150

Wheel Magnet Lithium Battery (CR2032)