User's Manual

ManualsBrandsCaterpillar ManualsElectronicsCaterpillar MSS3s RFID Key Reader Module

Illustration 49 g03866585

Time Zone

7. Select the local time zone from the drop-down list.

Illustration 50 g03866589

Local Date and Time

8. Enter the local date and time. Use an accurate

reference to set the time.

Note: Laptop clocks are not accurate and may have

a different time than the local time.

Illustration 51 g03866592

ET Display

9. Then press the “OK” button. The Cat ET will

display the following message.

Illustration 52 g03866593

Cat ET Time Confirmation

10. Click on the “Yes” button in order to change the

date and time or click on the “No” button in order to

cancel the change. The Cat ET will display the

new time on a 24 hour clock.

Illustration 53 g03866595

Cat ET Display 24 Hour Clock

i06229333

Software - Uninstall

( “Immobilizer” Feature)

SMCS Code: 7631-011

The “Uninstall” feature of the Machine Security

System MSS allows the user to uninstall the

Immobilizer feature from other electronic control

modules.

The MSS3s ECM should be removed after the

immobilizer software has been successfully

uninstalled. If the MSS3s ECM is not removed, the

LED for the status of the MSS will give a false

indication.

UENR7061 87

Testing and Adjusting

Summary of content (10 pages)

PAGE 1
UENR7061 87 Testing and Adjusting 9. Then press the “OK” button. The Cat ET will display the following message. Illustration 49 g03866585 Time Zone 7. Select the local time zone from the drop-down list. Illustration 52 g03866593 Cat ET Time Confirmation 10. Click on the “Yes” button in order to change the date and time or click on the “No” button in order to cancel the change. The Cat ET will display the new time on a 24 hour clock. Illustration 50 g03866589 Local Date and Time 8.
PAGE 2
88 Testing and Adjusting The “Uninstall” screen for the Machine Security System consists of the areas that are listed below: “ Status Line”” – The “status line” displays messages regarding the process of this function. Display Area – The “Uninstall” display for the Machine Security System consists of two columns. The two columns are the “ECM” column and the “Security System Status” column. The “ECM” column lists every ECM that is installed on the machine with the immobilizer feature.
PAGE 3
UENR7061 Illustration 54 Machine Security System Uninstall screen 7. Click on the “Uninstall” button that is located at the lower left-hand corner of the “Machine Security System Uninstall” screen. This button will cause the ET to display the “ Factory Password Screen” that is shown in Illustration 55 . Note: A factory password is required to perform the “Machine Security System Uninstall” . A master electronic key will not allow you to uninstall the Machine Security System.
PAGE 4
90 Testing and Adjusting UENR7061 Illustration 55 g03866606 Factory Password screen 8. The factory passwords are provided by the Factory Password System. Enter the factory passwords in the dialog boxes that are provided on the “Enter Factory Password” screen. Once the ET accepts the passwords, the screen shown in Illustration 56 will be displayed. Note: Pressing the “No” button aborts the “uninstall” of the Machine Security System.
PAGE 5
UENR7061 91 Testing and Adjusting Note: If the MSS3s ECM is configured to control other devices, (start relay and/or main power relay), those devices must be reconnected in accordance with the machine Electrical Schematic. i06229289 Glossary of Terms SMCS Code: 7631 Armed – The state of the security system when the machine is disabled. Disarmed – The state of the security system when the machine is able to operate normally.
PAGE 6
92 Testing and Adjusting UENR7061 i06227306 System Schematic SMCS Code: 7566 Refer to the corresponding schematic of the machine or Special Instruction.
PAGE 7
UENR7061 93 Index Section Index C F Cat Data Link - Test .............................................37 Diagnostic Trouble Code Procedure ..................37 Theft Deterrent Module ECM ............................37 Circuit Tests........................................................37 Connector Contact Description.............................59 ECM Pull Down Voltage ...................................59 ECM Pull Up Voltage........................................59 Input/Output ......................
PAGE 8
94 Index Section S Scheduled Access ( “Security System Bypass Times” ) ............................................................10 Service...............................................................52 Service Operation Using Machine Security System .............................................................14 Service Operation Using Service Tool ...................14 Service Tools ......................................................17 Software - Uninstall ( “Immobilizer” Feature)..........
PAGE 9
PAGE 10
UENR7061 ©2016 Caterpillar All Rights Reserved 96 August 2016 CAT, CATERPILLAR, their respective logos, “Caterpillar Yellow”, and the POWER EDGE trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.