CLI User Guide COORDINATOR / ROUTER User Manual All rights reserved by Allynk Technology Co. Ltd.
Coordinator / Router User Manual Table of contents 1 Specifications ..................................................................................................... 2 1.1 1.2 1.3 2 Coordinator Specifications ......................................................................................................... 2 Router Specifications.................................................................................................................. 3 FCC Requirement...................................
Coordinator / Router User Manual 1 Specifications 1.
Coordinator / Router User Manual Disconnect from Concentrator Only Blue On Sub-G RF error Connect to Concentrator Only Blue Blinks Sub-G RF error Only Red On Coordinator Ready All off Power On (1~4 sec) Only Green On User only sees Green LED on means Coordinator software might encounter some problems. 1.
Coordinator / Router User Manual Green On Blue On Blue Blinks Red On Router is in Standby state Router is in Connected state Router is in JoinNewPan or JoinOtherPan state Software error LED MicroUSB POE as power input source and no data is carried. LEDs on RJ45 connector are off all the time. Sub-G MAC Blue On SW Error JoinNewPan State JoinOtherPan State All off 1~4 sec Green On SW Error Red On Connected State Blue On SW Error All rights reserved by Allynk Technology Co. Ltd. ■8F., No.
Coordinator / Router User Manual 1.3 FCC Requirement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.
Coordinator / Router User Manual 2 Configure Coordinator Router is a “zero configuration” device. ⚫ Please download coordctl.zip from : Github: (Must have github account first) https://github.com/AllynkTechnology/coordctl/releases/latest ⚫ ⚫ ⚫ Unzip coordctl.zip to your forder OS supported : Linux platform : coordctl_cust Windows platform : coordctl_cust.exe Execute configuration tool (Take windows platform for example) 1. Run cmd.exe 2. Enter the folder you unzip coordctl.zip 3.
Coordinator / Router User Manual 1. Setup the environment Put coordinator to the same local network area (LAN) with your PC Laptop to run configuration tool Ethernet Switch Coordinator Coordinator will need microusb to supply power if not using POE switch 2. Read Coordinator’s hostname Step1: Check the sticker on the bottom of Coordinator Step2: Coordinator’s hostname = SMAC (Example) SMAC: C00000000050, Coordinator hostname: C00000000050 3.
Coordinator / Router User Manual C00000000050 netlas Username: netlas (User cannot modify) Default Password: netlas (User can modify) netlas 2.2 Configure Coordinator IP Coordinator ip settings 1 ① ② All rights reserved by Allynk Technology Co. Ltd. ■8F., No.20, Chenggong 13th St. Zhubei City, Hsinchu County 30264, Taiwan ■ allynk.com ■ contact@allynk.
Coordinator / Router User Manual ① DCHP fallback IP vs Static IP DHCP Fallback IP Ethernet Switch with DHCP enabled IP: Dispatched by DHCP server DNS: Dispatched by DHCP server Gateway: Dispatched by DHCP server Ethernet Switch with DHCP disabled IP: User configured DNS: User configured Gateway: User configured Fallback IP settings are only effective when DHCP server is not available Static IP Ethernet Switch (with or without DHCP) IP: User configured DNS: User configured Gateway: User configured ② IP
Coordinator / Router User Manual 3. Modify IP DHCP Fallback IP Static IP y y n y All rights reserved by Allynk Technology Co. Ltd. ■8F., No.20, Chenggong 13th St. Zhubei City, Hsinchu County 30264, Taiwan ■ allynk.com ■ contact@allynk.
Coordinator / Router User Manual Apply new IP settings to coordinator All rights reserved by Allynk Technology Co. Ltd. ■8F., No.20, Chenggong 13th St. Zhubei City, Hsinchu County 30264, Taiwan ■ allynk.com ■ contact@allynk.
Coordinator / Router User Manual 2.3 Configure Daemon Port Daemon Port Settings 2 Daemon port is the TCP port for program running within Coordinator to communicate with Concentrator program 1. Current Daemon port 2. Modify Daemon Port y All rights reserved by Allynk Technology Co. Ltd. ■8F., No.20, Chenggong 13th St. Zhubei City, Hsinchu County 30264, Taiwan ■ allynk.com ■ contact@allynk.
Coordinator / Router User Manual 2.4 Configure Time Zone Time Settings 3 TimeZone parameter should follow the format of TZ database name (ex: Asia/Taipei 、Asia/Tokyo、America/New_York…..) 1. Current time information 2. Modify time zone y All rights reserved by Allynk Technology Co. Ltd. ■8F., No.20, Chenggong 13th St. Zhubei City, Hsinchu County 30264, Taiwan ■ allynk.com ■ contact@allynk.
Coordinator / Router User Manual 2.5 Configure NTP Server NTP Settings 4 NTP server help eliminate time drift between coordinator and Concentrator program 1. Current NTP Server 2. Modify NTP server All rights reserved by Allynk Technology Co. Ltd. ■8F., No.20, Chenggong 13th St. Zhubei City, Hsinchu County 30264, Taiwan ■ allynk.com ■ contact@allynk.
Coordinator / Router User Manual y 2.6 Concentrator IP & Port Concentrator IP Settings 5 Set Concentrator IP to Coordinator will help user to add coordinator to Concentrator program reversely 1. Current Concentrator IP & port settings 2. Modify Concentrator IP & port All rights reserved by Allynk Technology Co. Ltd. ■8F., No.20, Chenggong 13th St. Zhubei City, Hsinchu County 30264, Taiwan ■ allynk.com ■ contact@allynk.
Coordinator / Router User Manual y y 2.7 Adjust User Account User account Settings 6 User list only shows users other than ‘Default user’ Coordinator cannot be configured once user forgets all accounts’ password. All rights reserved by Allynk Technology Co. Ltd. ■8F., No.20, Chenggong 13th St. Zhubei City, Hsinchu County 30264, Taiwan ■ allynk.com ■ contact@allynk.
Coordinator / Router User Manual 1. Modify current login user’s password y y 2. Add new account(s) In addition to default account, User can add up to 2 new accounts y y y: add another / n: quit All rights reserved by Allynk Technology Co. Ltd. ■8F., No.20, Chenggong 13th St. Zhubei City, Hsinchu County 30264, Taiwan ■ allynk.com ■ contact@allynk.
Coordinator / Router User Manual 3. Delete existing account(s) Default user cannot be deleted y y y: delete another / n: quit All rights reserved by Allynk Technology Co. Ltd. ■8F., No.20, Chenggong 13th St. Zhubei City, Hsinchu County 30264, Taiwan ■ allynk.com ■ contact@allynk.
Coordinator / Router User Manual 3 Install Coordinator and Router Screw the attachment on the ceiling. Plug in the Ethernet cable Put coordinator or router on the top of attachment, and rotate in the clockwise direction. All rights reserved by Allynk Technology Co. Ltd. ■8F., No.20, Chenggong 13th St. Zhubei City, Hsinchu County 30264, Taiwan ■ allynk.com ■ contact@allynk.
Coordinator / Router User Manual Coordinator is ready to connect to Concentrator when Blue LED is blinking. Next, Coordinator should be added and enabled in Concentrator program . Please refer to Concentrator documents for more information Router is ready when Green LED is on. Next, Router should be added to Sub-G network for further usage.
Coordinator / Router User Manual ⚫ Execute configuration tool (Take windows platform for example) 1. Run cmd.exe 2. Enter the folder you unzip coordctl.zip 3. Execute coordctl_cust.exe coordctl_cust.exe -control When you see the output as the figure below the configuration tool is ready. 4.1 Connect to Coordinator For setting up the connection between Coordinator and your PC, please refer to section 2.
Coordinator / Router User Manual C00000000050 netlas Username: netlas (User cannot modify) Default Password: netlas (User can modify) netlas 4.2 PAN control PAN is the network controlled by Coordinator 1 4.2.1 Check PAN information All rights reserved by Allynk Technology Co. Ltd. ■8F., No.20, Chenggong 13th St. Zhubei City, Hsinchu County 30264, Taiwan ■ allynk.com ■ contact@allynk.
Coordinator / Router User Manual 1 Field [PanID] [Enabled] [Channel] [Power] [BeaconInterval] [Awake] Descriptions Unique ID for this PAN ✓ true: PAN is on. (Can be stopped by Stop PAN) ✓ false: PAN is off. (Can be started by Start PAN) The radio frequency this PAN is using. Transmission power (Unit: dbm) The frequency of batch processing. ✓ true: PAN is awakening device. ✓ false: PAN is not awakening device. 4.2.
Coordinator / Router User Manual [Channel number] Physical radio frequency ⚫ Scan channel Scan channel can only be executed when PAN enabled = false 2 ➢ ➢ ⚫ Return value: true: This channel is available. Return value:: This channel is occupied. Start pan All rights reserved by Allynk Technology Co. Ltd. ■8F., No.20, Chenggong 13th St. Zhubei City, Hsinchu County 30264, Taiwan ■ allynk.com ■ contact@allynk.
Coordinator / Router User Manual 3 Tx Power should be lower than 8 when coordinator is used in Japan ➢ ➢ Return value: true: PAN has been started successfully Return value: false: Error happened during starting PAN. 4.2.3 Stop PAN 3 ➢ ➢ Return value: true: PAN has been stopped successfully Return value: false: Error happened during stopping PAN. All rights reserved by Allynk Technology Co. Ltd. ■8F., No.20, Chenggong 13th St.
Coordinator / Router User Manual 4.2.4 Awake devices within the PAN 4 ⚫ Start Awakening 1 ⚫ Stop Awakening 2 4.2.5 Expel devices from the PAN Before executing this operation, user should know the difference between activated and non-activated devices. All rights reserved by Allynk Technology Co. Ltd. ■8F., No.20, Chenggong 13th St. Zhubei City, Hsinchu County 30264, Taiwan ■ allynk.com ■ contact@allynk.
Coordinator / Router User Manual Device will save PAN’s information Device will search PAN’s signal if disconnecting from PAN PAN needs to execute awake PAN to make device connect Device will leave this PAN when user executes Purge PAN operation. Activated device Yes Yes Non-activated device No No No Yes No Yes So, Purge Pan is the operation to ask non-activated device to leave the PAN. 5 The list of purged device’s address will be returned when this operation is completed. 4.
Coordinator / Router User Manual ⚫ List the specific device’s information 1 ※ Press Enter to leave without changing current value Target Device will be kept until user modifies it again.
Coordinator / Router User Manual [ScanIteration] [UserDefinedBehavior] ➢ The number of Short Sleep repeated in the Short Sleep Period Image action when device’s state changes Sleep time and Sleep Period ScanIteration is to define the number of Short Sleep will be performed. After Short Sleep period ends, ESL tag will start Long Sleep period.
Coordinator / Router User Manual 3 ⚫ List all devices’ information (Sorted by device’s RSSI) 4 ⚫ List all devices’ information (Sorted by device’s battery voltage) All rights reserved by Allynk Technology Co. Ltd. ■8F., No.20, Chenggong 13th St. Zhubei City, Hsinchu County 30264, Taiwan ■ allynk.com ■ contact@allynk.
Coordinator / Router User Manual 5 4.3.2 Ping device(s) 2 ⚫ Ping single device All rights reserved by Allynk Technology Co. Ltd. ■8F., No.20, Chenggong 13th St. Zhubei City, Hsinchu County 30264, Taiwan ■ allynk.com ■ contact@allynk.
Coordinator / Router User Manual 1 ※ Press Enter to leave without changing current value Target Device will be kept until user modifies it again.
Coordinator / Router User Manual [JobId] [JobStauts] The identifier of previous executed operation (ESL will keep the last 4 operations.) The status of previous executed operation. (ESL will keep the last 4 operations.) If [Status] is not STATUS_OK, it means ping operation is not completed successfully ⚫ Ping all devices 3 4.3.3 Send image or command to device 3 ⚫ Set parameters ➢ Target device: Device’s extended address. All rights reserved by Allynk Technology Co. Ltd. ■8F., No.
Coordinator / Router User Manual 1 ➢ ※ Press Enter to leave without changing current value Target file: Image file (Please use image file generated by Allynk’s tool.) 2 ※ Press Enter to leave without changing current value ※ Press Enter to leave without changing current value The usage of image header: All rights reserved by Allynk Technology Co. Ltd. ■8F., No.20, Chenggong 13th St. Zhubei City, Hsinchu County 30264, Taiwan ■ allynk.com ■ contact@allynk.
Coordinator / Router User Manual Sent from Coordinator Image Header Image Data Received IMG (Save to Lot9) to ESL Save to Lot9 but not display Byte 2 Byte 1 Lot: 0x0~0x9: Lot0~Lot9 Other values: invalid Byte 0 Operations: 0x0: Prioritized save and display 0x1: Save only 0x4: Save and display Other values: invalid 0x0 (Fixed value) ※ Header = 0x 09 01 00 Operation: Prioritized save & display Descriptions Save and display this image with priority.
Coordinator / Router User Manual ➢ Target command: Command contents 3 Available command: Command activate config -inv1 -inv2 -iter -epd (※ inv1 / inv2 / iter / epd parameters are optional, user can use all of them or one of them) deactivate imgshow -current imgshow -index <0~9> ledon ledoff ledblink -on -off -interval (※ on / off / interval parameters are all needed) Descriptions Activate device Modify ESL’s configurations ✓ inv1: ScanInte
Coordinator / Router User Manual 500ms ON OFF 500ms ON OFF 500ms ON OFF 20 seconds ⚫ Send image (1) Check if target device is correct. Modify it if not correct. (2) Check if target file is correct. Modify it if not correct. (3) Send image 4 ⚫ Send command (1) Check if target device is correct. Modify it if not correct. (2) Check if target command is correct. Modify it if not correct. (3) Send command All rights reserved by Allynk Technology Co. Ltd. ■8F., No.20, Chenggong 13th St.
Coordinator / Router User Manual 5 4.4 Reconnect Reconnect can check and repair TCP/IP connection when it is broken in the middle of operation. 3 All rights reserved by Allynk Technology Co. Ltd. ■8F., No.20, Chenggong 13th St. Zhubei City, Hsinchu County 30264, Taiwan ■ allynk.com ■ contact@allynk.