VEGA9300 User’s Manual V0.3 Version: 0.3 Date: July 20,2005 Castles Technology Co., LTD. Tel: 886 (2) 8913-1771 Fax: 886 (2) 8913-1772 E-Mail: casauto@casauto.com.tw Web: www.casauto.com.tw © Castles Technology Co., LTD.
VEGA9300 User's Manual V0.3 WARNING Information in this document is subject to change without prior notice. No part of this publication may be reproduced, transmitted, stored in a retrieval system, nor translated into any human or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual, or otherwise, without the prior written permission of Castles Technology Co., LTD. All trademarks mentioned are proprietary of their respective owners. Note: 1.
VEGA9300 User's Manual V0.3 Table Of Contents WARNING........................................................................................................2 1. Introduction .................................................................................................4 1.1 Front View ..................................................................................4 1.2 Side View ...................................................................................5 1.3 Head View .........................
VEGA9300 User's Manual V0.3 1. Introduction 1.1 Front View Paper Roll Box Power Key F1 Key LED (Green) LED (Orange) LED (Red) F2 Key F3 Key F4 Key Cancel Key Clear Key Enter Key 1. Power Key:Power On- Press Power Key 3 Second To Start. 2. Press Off- Press Power Key To Turn Off F1 Key:Press F1 To The Download Main Menu To Enter The Download 3. Mode Under The Program Manager Screen. Press Cancel Key Will Go Back To The Program Manger Screen.
VEGA9300 User's Manual V0.3 1.2 Side View Handset Smart Card Insert Location Base 1.3 Head View RS485 RS232 LAN Phone Line Switch Power Switch Phone Line Switch Power Cord 1. Power Cord:For Connecting To The Power. (Please Notice The Correct 2. Position) Power Switch:For Controlling The Power Of The Base. 3. 4. 1. (Make Sure That The Handset Must Attach With The Base And Both Power Switch On To Fully Recharge The Terminal. RS485:RJ11, Only Provide In VEGA 9310 Model.
VEGA9300 User's Manual V0.3 1.4 Back View Rechargeable Batter Cover Rechargeable Battery Cover 4 SAM Slots Rechargeable Battery Box Open The Rechargeable Battery Cover, Release The Rechargeable Battery Box For Inserting The SAM Card Castles Technology Co., Ltd. All rights reserved.
VEGA9300 User's Manual V0.3 1.5 Magnetic Stripe Card Reader & Smart Card Introduction 1. Base Power LED 2. 1. 2. Magnetic Stripe Card Should Be Placed On Card Reading Slot With Magnetic Stripe Facing Left, Swipe The Card From Top To The Bottom. Insert User IC Card With Chip Facing Up. Castles Technology Co., Ltd. All rights reserved.
VEGA9300 User's Manual V0.3 1.6 Handset and the Base Connection 1.6.1 Pull Out Release The Handset By The Following Instruction. 1.6.2 Pull Back Put Back The Handset Back To The Base As The Below Instruction 1.7 Rechargeable Battery Installation Release The Rechargeable Battery, Loose The Screws To Install The Battery According to “+” or “-“ Caution:Please Use 2000mAh Rechargeable Battery. And Make Sure To Fully Charge The Battery Up To At Least 4 Hours.
VEGA9300 User's Manual V0.3 1.8 SAM Card Installation 1. Open The Rechargeable Battery Box To Find 4 SAM Card Slots And Turn To The Left To Open 2. Place The SAM Card To The Upper Position With Chip Facing Down As The Below Picture 3. Close Down The Case And Push Forward To Lock Castles Technology Co., Ltd. All rights reserved.
VEGA9300 User's Manual V0.3 1.9 Paper Roll Installation Insert The Paper Roll To The Box And Pull The Paper Down As The Picture. Close The Paper Roll Box To Start Paper Loading. Castles Technology Co., Ltd. All rights reserved.
VEGA9300 User's Manual V0.3 1.10 Power Please Connect With The Attached DC 12V Adapter. Input : 100 ~ 240 Vac, 50 ~ 60Hz , 1.8A Max. Output : 12Vdc, 3.3A Castles Technology Co., Ltd. All rights reserved.