User's Manual

ManualsBrandsCASTLES TECHNOLOGY ManualsElectronicsContactless Module

Castles Technology

Contactless Reader Module CA-CLM User’s Manual

警語

依據低功率電波輻射性電機管理辦法

第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用

者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。

第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信。低功率

射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

Introduction

Castles Technology CA-CLM contactless reader module is based on RFID (Radio

Frequency Identification) technology and adopted HF (High Frequency) 13.56MHz

band to have the communication protocol ISO14443 type A, B standard to interact

the contactless smart card (a specified RFID tag) for specified applications like

payment control and scheme. The reader has a baseband processer to handle host

communication through RS232 interface, and to communicate RF analog front end

(RF band chip) through SPI interface. RF chip is charged of air interface protocol and

modulation to handle the communication with contactless smart card or so-called

RFID tag through antenna. When the reader is operating, RF energy is transmitted by

RF chip through antenna continually, and also the polling of response of card landing,

once card is close to reader antenna, card will be energized by reader antenna RF

energy, and responses to reader in specified standard for application required from

host. The reading or writing of card will be occurred frequently during card landing

on the reader. Also the indication LEDs and buzzer are included in this module for

application need. Following is a block diagram about CA-CLM contactless reader to

show the structure of RFID reader did.

Summary of content (6 pages)

PAGE 1
Castles Technology Contactless Reader Module CA-CLM User’s Manual 警語依據低功率電波輻射性電機管理辦法第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 Introduction Castles Technology CA-CLM contactless reader module is based on RFID (Radio Frequency Identification) technology and adopted HF (High Frequency) 13.
PAGE 2
MB J1 FFC Cable 0.5mm 14P 8cm ANTENNA/B J2 RS-232 (COM port), FFC Cable 1.
PAGE 3
Operation This module only allow 5V DC power source for operating power used, and a battery backup 3V DC for RTC used (backup power is required if necessary). The host side has a RS232 interface for host connection to receive or transmit relevant data from or to host may be like PC or Embedded system which AP (Application Program) executed. Antenna board should be connected to MB with a FFC cable when you received. The blue LED on antenna board will be on and buzzer beep when power on normally.
PAGE 4
2D: Any metal or conductive material is forbidden in the operating area shown as below. 2.5 cm Antenna/B 3.5 cm 3.5 cm 2.5 cm 3D: Any metal or conductive material is forbidden in the operating volume shown as below. 4 cm 2.5 cm 3.5 cm 4 cm Environmental Operating temperature: 0℃ to 40℃ Storage temperature: -20℃ to 80℃ Operating humidity: 15% to 90%, non-condensing Certificate Compliant EMVCo 2.
PAGE 5
虹堡科技股份有限公司 (Castles Technology Co., Ltd) 辛華熙 (Kevin Xin) 231 新北市新店區北新路三段 205 號 2 樓 (2F, No.205, Sec.3, Beixin Rd.
PAGE 6
警語依據低功率電波輻射性電機管理辦法第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 Notice This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.