User's Manual

ManualsBrandsCastleNet Technology ManualsComputers & AccessoriesWIFI cable modem router

CGA0101 Wireless Cable Gateway Quick Installation Guide

Package Contents

 CGA0101 cable modem * 1

 Quick Installation Guide * 1

 RJ-45 CAT 5e cable * 1

 12 V/1.5 A Power Adaptor * 1

 Telephone cord * 1

Rear Panel and Hardware Connection

This chapter describes the proper steps for connecting your cable modem. Please be sure to follow

the steps in the sequence outlined below. Failure to do so could result in improper operation or failure

of your cable modem.

Please be reminded this product CGA0101 is designed to stand in vertical position in order to keep the

ventilation as clear as possible. Please do not put it down horizontally.

Step 1: Connect a cable by feeding the F-connector on the back of the cable modem. Ensure the

center conductor of the 75 ohm coaxial cable is inserted directly into the center of the F-connector.

Secure the coaxial cable by carefully threading the outer shell of the coaxial cable connector onto the

F-connector in a clockwise direction until tight. Be careful not to over-tighten the connector or you may

damage either the connector or the cable modem.

Step 2: Connect the cable modem to IEEE 802.3 10Base-T / 802.3u 100Base-TX / 802.3ab

1000Base-T Network using a RJ-45 male-terminated Ethernet cable. This cable modem equips with

two Ethernet ports, you can connect two PCs to the cable modem at the same time if necessary.

Step 3: Connect the telephone sets to TEL. Use RJ-11 telephone line to connect TEL port on the

cable modem and telephone socket on telephone

Step 4: Connect the AC Adapter to the cable modem by inserting the barrel-shaped connector into the

mating power connector on the back of the cable modem. Exercise carefully to ensure the connectors

are properly aligned prior to insertion and ensure the two connectors engage completely. The cable

modem is shipped with an AC adapter. Remember to use only power adapter that came with the cable

Step 1 Connecting

the Coaxial Cable

Step 2 Connecting to a

Network Interface Cord

Step 3 Connecting

the Telephone cord

Step 4 Connecting

to the AC Adapter

Summary of content (8 pages)

PAGE 1
CGA0101 Wireless Cable Gateway Quick Installation Guide Package Contents    CGA0101 cable modem * 1 Quick Installation Guide * 1 RJ-45 CAT 5e cable * 1   12 V/1.5 A Power Adaptor * 1 Telephone cord * 1 Rear Panel and Hardware Connection This chapter describes the proper steps for connecting your cable modem. Please be sure to follow the steps in the sequence outlined below. Failure to do so could result in improper operation or failure of your cable modem.
PAGE 2
CGA0101 Wireless Cable Gateway Quick Installation Guide modem. Other power adapters might have voltages that are not correct for your particular cable modem. Using a power adapter with the wrong voltage can damage the cable modem. Step 5: Adjust the antenna if necessary. Step 6:The screen of the coaxial cable is intended to be connected to earth in the building installation.
PAGE 3
CGA0101 LED Wireless Cable Gateway Quick Installation Guide NAME COLOR POWER Green MODE On DC power connected Off No DC power connected Blinking Green ▼ DS Green Green ▲ US Green LAN1 LAN2 Wi-Fi WPS Green Green & Orange Green & Orange Green Green Downstream locked Off Cable interface idle On W/DS locked Off W/DS disabled or CM standby Blinking Upstream ranging On Upstream locked Off Cable interface idle On W/US locked Off W/US disabled or CM standby Green CM provisio
PAGE 4
CGA0101 Wireless Cable Gateway Quick Installation Guide Accessing the Web Management For easy-changing the default settings, a Web-based GUI is built-in for your access. Use the following procedures to login to your CGA0101. 1. Open your web browser. Type the default IP address of the CGA0101 (e.g. http://192.168.0.1) and press Enter.
PAGE 5
CGA0101 Wireless Cable Gateway Quick Installation Guide Check your CGA0101 Access Information There is a label pasted to the bottom of CGA0101 case. In that label, you can obtain following information. Pls note, following label is just an example, each CGA0101 has their own label and setting value. Pls follow your label information to access and configure CGA0101. In normal case, you don’t need to change anything, all setting have been set and work properly.
PAGE 6
CGA0101 Wireless Cable Gateway Quick Installation Guide Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 7
CGA0101 Wireless Cable Gateway Quick Installation Guide IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
PAGE 8
CGA0101 Wireless Cable Gateway Quick Installation Guide Canada-Industry Canada (IC) Operation is subject to the following two conditions: this device may not cause interference and this device must accept any interference, including interference that may cause undesired operation of the device. IMPORTANT NOTE: IC Radiation Exposure Statement: This equipment with IC radiation exposure limits set forth for an uncontrolled environment.