Contents/Ready Phone Call Inputting Characters Address Book/ Pair Function Mail Camera EZweb EZ Navi au Media Tuner Other Functions Basic Manual Troubleshooting/ Remote Ctrl Lock Index
Introduction Thank you for purchasing the W62CA. Before using it for the first time, be sure to read the Basic Manual (this PDF manual) so as to know how to use it correctly. After you finish reading this manual, store it and the printed materials that come with the phone in a safe place for future reference. Printed Manuals for the W62CA (Japanese) The W62CA comes with a Basic Manual and an Instruction Manual.
Cellphone Etiquette Mind your manners! A cellphone always emits weak radio waves while it is turned on. Enjoy operation of your cellphone without forgetting to be considerate of those around you. Some locations do not allow the use of cellphones. ■ Using a cellphone while driving is dangerous and prohibited by the Traffic Control Law. ■ Using a cellphone inside of an aircraft is prohibited by the law. Be sure to turn off your cellphone before takeoff.
Cellphone Basics Features Camera EZ Navi EZ FeliCa Shoot photos and record movies, and send them by e-mail. EZ Navi Walk, Passenger Seat Navi, Evacuate Navi and Security Navi allow you to get various kinds of location information. They are all built-in functions. Page Use the cellphone for shopping by using electronic money, or use it as member’s cards, point cards, and so on. au Media Tuner Security Setup Mail Enjoy using Television (1Seg) and EZ Channel-Plus.
Manner Mode and Answer Memo Manner Mode Answer Memo Use Manner Mode to turn off the ringtone so as not to bother others around you. If you cannot answer a call, Answer Memo plays an answering message and records the caller’s message. While the standby screen is displayed, hold down ( for at least one second. While the standby screen is displayed, hold down C for at least one second. Page 35 Page 36 Checking Power, Signal Strength, and Battery Level Normally leave the phone turned on.
Never use your cellphone while driving! Do not use the cellphone while driving a car/motorcycle/bicycle. It may cause a traffic accident. Use of the cellphone while driving a car/motorcycle is forbidden by the law. Use of the cellphone while driving a bicycle may be punished by the law too. × Reading mail or looking at the display. × Holding a cellphone in your hand to talk. Turn off your cellphone or use Drive Mode while driving.
Beware of spam and One-ring Calls! If you get spam You can set up mail filters to block specific mail or spoof mail. The following are the main features your cellphone uses to block spam. ・Blocking of “未承諾広告※” (unsolicited advertisement) mail ・Blocking of specific mail ・Blocking of spoof mail Page 55 Beware of One-ring Calls! A “One-ring Call” (wan-giri in Japanese) rings your phone only once, in an attempt to make you call back to a service that automatically bills you very high charges.
Disaster Message Board Service Disaster Message Board The Disaster Message Board lets you use EZweb to register information about your well-being in case of a major disaster. The information you register can be accessed from anywhere in Japan over EZweb or the Internet.
Registration Access Disaster Message Board top screen Information registration screen Information screen ※ Registration contents are retained for up to 72 hours. ※ You can register up to 10 entries per phone number. Registering a new entry while there are already 10 registered entries, automatically overwrites the oldest entry.
Contents Cellphone Etiquette Phone Call 1 Mind your manners! ......................................1 Cellphone Basics 2 Features ........................................................2 Manner Mode and Answer Memo .................3 Checking Power, Signal Strength, and Battery Level ...............................................3 Never use your cellphone while driving!........4 Beware of spam and One-ring Calls! ............5 Disaster Message Board Service..................
Camera 59 EZweb Contents Using the Camera .......................................59 Shooting a Photo ........................................61 Viewing Photos ...........................................62 Attaching a Photo to an E-mail Message ....63 64 Using EZweb...............................................64 Displaying the au one Top ...........................65 Bookmarking Sites You Frequently Access .................................................................66 Viewing a Bookmarked Site .
Ready All Before using the W62CA, check the contents of the package coming with your W62CA. You should also familiarize yourself with basic operations, like how to charge the battery, how to turn the power on, etc.
Names of Parts ■ Front ■ Back Ready Temperature sensor Earpiece FeliCa mark Speaker Main display Sub display Photo light/ Pocket light LED indicator Bumper A Built-in TV antenna※3 Camera lens Infrared port Camera start indicator Screw type battery lock Center key Cursor key Optical sensor Application key Address book key EZ key Mail key Answer/Pair key Clear/Memo key End/Power key Number keys Battery pack/cover Microphone※1 Bumper B Built-in antenna※2 Attach/remove au IC-Card or microSD™ mem
Charging the Battery Pack The battery pack that comes with the phone is not fully charged when you purchase it. Be sure to charge the battery pack before using the W62CA for the first time. Charging takes about 140 minutes. You should recharge the battery pack whenever the battery level icon shows or . Aligning the locking tabs of the desktop holder with the slots on the sides of the phone, attach the phone to the holder in the sequence , .
Connect the common AC adaptor 01/02 (option) to the desktop holder. Ready Check the shape of the connectors to ensure they are aligned correctly before you connect. Trying to force a connection may damage the connectors. Attach the closed phone to the desktop holder in the sequence , , aligning the locking tabs of the holder with the slots on the sides of the phone. Fold out the power plug of the common AC adaptor 01/02 (option), and then plug it into a 100V AC power outlet.
Turning On Power Hold down F for at least 2.5 seconds. The message “Now Loading...” will appear on the display for a short while, followed by the standby screen. Icon Signal Strength Strong Medium Weak Very Weak Out of Range • Communication is not possible while the signal strength icon is (Out of Range). • Communication may not be possible while the signal strength icon is (Very Weak).
Security Code and Passwords Ready The W62CA lets you use the numbers and passwords described below. Be sure to take steps so you do not to forget your numbers and passwords. You will need them to perform various operations and to access subscription services.
Selecting English as the Display Language While the standby screen is displayed, press c. Use j to select “機能” (Function), and then press c (選択) (Select). Press 3 (画面表示) (Screen Display).
Press 4 (Set Language). Ready Press 2 (English). This selects English as the display language. Even if English is selected as the display language, schedule and other dates are displayed in the format year/month/day. Folder names inside of the Data Folder are also displayed in year/month/day format.
Operation Basics ■ Key functions l • • c • • & • • L • • N • • C j • r • Displays incoming histories. Selects an item. Displays the main menu. Applies an item. Displays the address book. Creates a new address book (hold down for at least one second). E-mail C-mail (hold down for at least one second) Dials/answers a phone call. Displays the Pair Function. Memo Toggles Answer Memo on and off (hold down for at least one second). • Deletes a character. • Returns to the previous menu screen.
Display Indicators abcdefg h a Signal strength b Battery level c The microSDTM memory card (commercial item) is inserted into the cellphone. o d ／ ／ e f p k h Unread mail h Current time※ The date and time are set automatically. i Selects the user defined icons such as Photo (DSC Mode), calculator, Emission OFF Mode, G’zGEAR, Sports Timer, and “01 カシオからの ご案内” (information from CASIO)(Notepad 01), etc. by pressing d and a.
Main Menu There are four initial main menus (“Carbon pattern,” “G-gallery,” “Eco & Ego G,” and “Simple”) for W62CA. Pressing c while the standby screen is displayed displays the main menu. The menu structure depends on the type of the main menu. ■ Using the “Carbon pattern” menu If your cellphone color is “Burned Black,” the initial main menu is “Carbon pattern.” Use a to select the icon, and then press c (Select) to access the function associated with the icon.
■ Using the “G-gallery” menu G’zGEAR Camera Sports Timer LISMO Player Run&Walk Menu TV Life&News Data Folder Function Accessories Ready If your cellphone color is “Frozen White,” the initial main menu is “G-gallery.” Use a to select the icon, and then press c (Select) to access the function associated with the icon. ■ Using the “Eco & Ego G” menu If your cellphone color is “Sparkling Green,” the initial main menu is “Eco & Ego G.
■ Using the “Simple” menu Use j to select the icon, and then press c (Select) to access the function associated with the icon. Camera Photo/Movie/Bar Code Reader LISMO Player Play music/video clips G’zGEAR EARTH COMPASS, EARTH LOCATOR, HEAT GAUGE, SEA TIDE, etc.
■ Using Soft Keys Left Center Right Left soft key & Executes the function on the left. Ready Soft keys are the keys you use to execute the functions along with the bottom of the screen. The table below explains how to assign the soft keys to the on-screen functions. Note that the function of each soft key depends on the currently displayed screen. Center soft key c Executes the function on the center. Right soft key % Executes the function on the right.
Initializing E-mail and EZweb An EZweb subscription is required to use e-mail, EZweb or other EZ services. If you did not subscribe when you purchased your phone, contact your nearest au shop or the au Customer Service Center. ※ You will be assigned an e-mail address automatically when you perform the EZweb initialization procedure. While the standby screen is displayed, press L. Press c (OK). Wait until the phone connects to the server for initialization.
My phone number and mail address Ready Looking Up Your Current Phone Number and E-mail Address While the standby screen is displayed, press c. Press 0. Your current phone number and e-mail address appear.
Changing Your E-mail Address E-mail address △△△@ezweb.ne.jp Part you can change Domain name While the standby screen is displayed, press L. Press 0 (E-mail Setup). Press 4 (Other). Press 1 (Eメールアドレ スの変更) (Change E-mail Address).
Ready Enter your Security Code, press c (OK), use j to select “送信” (Send), and then press c (Select). Use j to select “承諾す る” (Accept), and then press c (Select). Use j to select the text box, and then press c (Input). Enter the e-mail address you want, and then press c (OK). To input an e-mail address →“Inputting an E-mail Address” (page 39) Use j to select “送信” (Send), and then press c (Select). The e-mail address confirmation screen appears. Press j to select “OK,” and then press c (Select).
Phone Call Making a Call While the standby screen is displayed, use the number keys (0 to 9) of the keypad to enter the phone number you want to call. When calling a standard phone, you need to enter the area code. Press N. After you finish a call, press F to hang up. ※ The caller always hears your voice even when you cover the microphone with your hands.
Making an International Call ■ au International Call Service Available without any additional application. Ex: To call 212-123-△△△△ in the USA 005345 212 Area code Country code (USA) 123 △△△△ Press N. Phone number • Calling charges for this service are added to monthly mobile phone calling charges and billed together. • Please check the Country code at the au Customer Service Center. • For charges, please refer to the au MOBILE PHONE SERVICE GUIDE or the au Customer Service Center.
Answering a Call Press N to answer an incoming call. After you finish a call, press F to hang up. Display for Incoming Calls If the caller’s name is in your address book, it appears on the display. If not, only the caller’s phone number is displayed. A message appears when the phone number of the caller is not provided for some reason. ID Unsent: The caller’s phone refused to send its phone number. Payphone: The call is from a payphone. Not Support: The call is from a phone that does not support caller ID.
Redialing (Outgoing Histories/ Incoming Histories) r: Displays outgoing histories. l: Displays incoming histories. Phone Call While the standby screen is displayed, press s. Use j to select the number you want to dial, and then press N. The phone stores up to 50 histories each for the outgoing histories and incoming histories. When a history is created while there are already 50 histories in memory, the oldest current history is deleted automatically to make room for the new one.
Changing the Ringtone While the standby screen is displayed, press c, use a to select “Function,” and then press c (Select). Press 2 (Sound/Vib/ Lamp). Press 1 (Incoming Setup). Press 1 (Incoming Call).
Use j to select and press c (Select). To hear the currently selected ringtone, press & (Play). Phone Call Press 1 (Original). Use j to select the ringtone you want, and then press c (Set). Press % (OK). The ringtone is set. You can also download a “Chaku-Uta®” from the Internet and use it for your ringtone.
Adjusting the Ringtone Volume To adjust the ringtone volume, perform steps 1 through 4 under “Changing the Ringtone” (page 32), and then continue with the following steps. Use j to select and press c (Select). Use j to adjust the ringtone volume, and then press c (Set). u: Increases volume. d: Decreases volume. Press % (OK). STEP앖 : Ringtone volume gradually increases. STEP앗 : Ringtone volume gradually decreases. OFF: Ringtone does not sound. 34 Beep, e ...
Adjusting the Earpiece Volume during a Call Hello? u: Increases volume. d: Decreases volume. Phone Call During a call, use j to adjust the volume. You can adjust the earpiece volume (level 1-5 and Max). Turning On Manner Mode While Manner Mode is set to on, the phone alerts incoming calls to you by vibrating. While the standby screen is displayed, hold down ( for at least one second. This turns on Manner Mode. The icon appears on the display while Manner Mode is turned on.
Turning On Answer Memo While the standby screen is displayed, hold down C for at least one second. This turns on Answer Memo. The Memo is turned on. icon appears on the display while Answer You can use Answer Memos (up to 6 memos), and each memo can contain up to 30 seconds recording time. To turn off Answer Memo, hold down C for at least one second.
Playing an Answer Memo When there is a recorded Answer Memo The message “Answer Memo” appear on the standby screen. Phone Call Select “Answer Memo,” and press c (Select). “Answer Memo List” appears. Use j to select the Answer Memo you want to hear, and then press c (Play). The Answer Memo plays back. To delete an Answer Memo, press C11 while the standby screen is displayed. Select the Answer Memo you want to delete, press % (SubMenu), and then 1 (Delete).
Inputting Characters Input characters using keypad keys 0 through 9, and *. The table below shows the characters each key cycles through when you press it. d e f Key 2 3 4 5 6 1 .
Inputting an E-mail Address mark@ ■ Inputting “mark@ezweb.ne.jp” In this example, we will input “mark@ezweb.ne.jp” for [E-mail Address1]. To input [E-mail Address1], perform steps 1 through 6 under “Registering an Address Book” (page 41), and then perform the following steps. Input “mark.” Press 6 once. Press 2 once. Press 7 three times. Press 5 twice. Press % (SubMenu), and then 3 (Phrase).
Inputting Pictograms The following procedure shows how to input pictograms into the body text when creating a new e-mail message. Press R. You can switch between Pictogram→ Symbol (Full-Size/Half-Size)→Face Mark →Pictogram by pressing R. Use a to select the pictogram you want, and then press c (Select). Use % (Category) or */# to scroll through the various categories of pictograms. To input pictograms consecutively, press & (Repeat) instead of c (Select).
Address Book Registering an Address Book While the standby screen is displayed, hold down & for at least one second. Address Book Select “ [Name],” and then press c (Select). Enter the name, and then press c (OK). The [Reading] is generated automatically when you enter a name. To input text →“Inputting Characters” (page 38) Use j to select “ [Phone No.1],” and then press c (Select).
Enter the phone number, and then press c (OK). Use j to select the No. Type, and then press c (Select). When entering the number of a standard phone, be sure to include the area code. Use j to select “ [E-mail Address1],” and then press c (Select). If you do not want to enter an e-mail address, jump to step 8. Enter the e-mail address, and then press c (OK). Use j to select the E-mail Type, and then press c (Select). To input an e-mail address →“Inputting an E-mail Address” (page 39) Press % (Reg).
Editing an Address Book Record Address. . . Birthday. . . Group. . . Example: To edit the phone number of “Tom Carter” While the standby screen is displayed, press &, use a to select the record you want to edit. Address Book Press c (Detail), and then & (Edit). Use j to select “ 0900006XXXX,” and then press c (Select). Make the changes you want, press c (OK). Use j to select the No. Type, and then press c (Select). To delete characters, press C. Press % (Reg).
Adding Outgoing or Incoming History Data to the Address Book While the standby screen is displayed, press s, use j to select the phone number you want to register, and then press % (SubMenu). r: Displays outgoing histories. l: Displays incoming histories. Press 2 (Reg to Adrs Book). Press 1 (Register New). Use j to select the No. Type, and then press c (Select). The phone number is entered automatically. To enter the name and other items, refer to step 2 under “Registering an Address Book” (page 41).
Dialing from the Address Book Press c (Detail). The detail screen of the record appears. Address Book While the standby screen is displayed, press &, and then use a to select the record whose phone number you want to dial. Hello? Use j to select the phone number, and then press N.
Pair Function You can register up to five phone numbers (like frequently used ones from the address book). You can make calls or send mails to these registered numbers (called Pair Partners) more easily. Registering a Pair Partner While the standby screen is displayed, press N. Use s to select the 1 through 5 tab where you want to register the Pair Partner. Use j to select “Reg./ Can.,” and then press c (Select). Press 1 (YES).
Making a Phone Call or Sending Mail to a Pair Partner While the standby screen is displayed, press N. Pair Function Use s to select the Pair Partner. Use j to select “Call,” and then press c (Select). Sending E-mail: Selecting “E-mail” and then pressing c (Select) will display a screen for composing and sending an e-mail message. Sending C-mail: Selecting “C-mail” and then pressing c (Select) will display a screen for composing and sending a C-mail message.
Mail EZweb subscription required Your W62CA supports two types of mail: e-mail and C-mail. Using E-mail To use e-mail, you need to subscribe to an EZweb service. If you did not subscribe when you purchased your phone, contact your nearest au shop or the au Customer Service Center. In addition to an EZweb subscription, you also need to perform an initialization procedure before you can use e-mail. If you have not performed initialization yet, refer to “Initializing E-mail and EZweb” (page 24).
Using C-mail C-mail lets you exchange text messages that contain up to 50 double-byte characters (100 single-byte characters) with another au cellphone that supports C-mails. Page 56 ※ C-mail transmission fee is charged when sending C-mail. C-mail Center Received using a phone number. Example: 090-0002-XXXX Mail Sent using a phone number. Example: 090-0001-XXXX C-mail can be sent to another au cellphone.
Creating and Sending E-mail Messages While the standby screen is displayed, press L. Press 1 (Create New). Select “ Address,” and then press c (Select). Press c (Select). : Address to which the e-mail will be sent. You can send e-mail up to 30 recipients (includes To/Cc/Bcc, within 640 singlebyte characters) at a time. When Adrs. Count Limit is set to “Restrict,” you can send up to 5 recipients at a time (includes To/Cc/Bcc, within 640 single-byte characters).
Use j to select the e-mail address you want to enter, and then press c (Select). Press & (OK). Use j to select “ Subject,” and then press c (Select). : Subject of the e-mail message. Mail Enter the subject, and then press c (OK). Use j to select “ Text,” and then press c (Select). : Body of the e-mail message. Enter the body text, and then press c (OK). Press & (Send) or N. The message “E-mail Sending completed.” appears on the display after the e-mail message is sent.
Reading Received E-mail Messages When you receive an e-mail The message “E-mail” and the standby screen. appear on E-mail icon Select “E-mail,” and then press c (Select). Press c (Select). : Indicates an unread message. : Indicates an already read message. Use j to select the unread e-mail you want to view, and then press c (Select). The received e-mail message appears. If all of the message cannot be displayed, press d to scroll. Use L and R to scroll between messages.
Reading an E-mail Message with an Attached Photo Use j to select the e-mail message, and then press c (Select). Mail Use j to select the attached data, and then press c (Select). Use j to select a file name, and then press c (Play). ◎ Depending on the type of the attached data, the contents may be displayed at the last of the body text. ◎ Depending on the size of the attached data, it may not come in at the same time as the mail message.
Replying to a Received E-mail Message To reply to an e-mail message, perform steps 1 through 3 under “Reading Received E-mail Messages” (page 52), and then perform the following steps. Press & (Reply). (Subject) is prefixed with “Re:,” and the body text of the e-mail is quoted. Use j to select “ Text,” and then press c (Select). For the remainder of this procedure →Perform the procedure starting from step 7 under “Creating and Sending E-mail Messages” (page 50).
Avoiding Spam It is recommended that you use our mail filter function to block spam. You can use the “Supportive settings” to easily configure mail filter settings by answering questions that appear on the display. ■ Configuring Mail Filter Settings Example: To access the “サポート設定” (Supportive settings) a While the standby screen is displayed, press L. b Press 0 (E-mail Setup) ➔ 3 (Mail Filter). c Use j to select “次へ” (Next) and then press c(Select). d Enter your Security Code, press c(OK).
Creating and Sending C-mail Messages While the standby screen is displayed, hold down L for at least one second. Press 1 (Create New). Enter the body text, and then press c (OK). Select “ [Address],” and then press c (Edit). 56 Hold down ...
Press 1 (Quote Adrs Book), use a to select an addressee, and then press c (Detail). You can also select a phone number from sent histories or received histories, or you can enter an address. Use j to select the phone number you want to enter, and then press c (Select). When the C-mail reaches the other party, the message “Mail delivered” appears, and the message is stored in the Outbox. Mail Press & (Send) or N.
Reading Received C-mail Messages When you receive a C-mail The message “C-mail” and the standby screen. appear on Select “C-mail,” and then press c (Select). Press c (Select). : Indicates an unread message. : Indicates an already read message. Use j to select the unread C-mail you want to view, and then press c (View). The received C-mail message appears. Use L and R to scroll between messages. Press C to return to the C-mail message list.
Camera The W62CA has a CMOS camera with approximately 1.97 million effective pixels and powerful functions to support various types of digital imaging. You can attach the photos that you shot to e-mail messages. Using the Camera Shooting a Photo (page 61) 1 Use your images for W62CA functions! You can use photos you shot for the standby screen, for the image that appears when receiving a call, and in your address book.
Tips for Better Photos Shooting with W62CA open Do not cover the lens or optical sensor with your hands. Hold the camera securely with both hands. Use your thumb to press c (Shoot) to release the shutter. Tips for Avoiding Hand Movement ● Remain steady by keeping your arms lightly against your sides and standing with your feet about shoulder width apart. Having your arms away from your side or extended in front of you can cause blurred images.
Shooting a Photo While the standby screen is displayed, press c, use a to select “Camera,” and press c (Select). Press 1 (Photo (W.paper Mode)). Point the lens at the subject, and press c (Shoot). Camera The phone emits a shutter sound. Note that the phone emits the shutter sound even if it is in Manner Mode. Check the subject through the monitor screen (within the area indicated as ), and release the shutter. Press c (Save).
Viewing Photos While the standby screen is displayed, press c, use a to select “Data Folder,” and then press c (Select). Use j to select “Photo Folder,” and then press c (Select). Selecting “All Data” displays a list of all photos in the “Photo Folder.” Use j to select the folder, and then press c (Select). A list of all photos that were shot on that day are displayed. Use a to select the photo you want to view, and then press c (Select). The photo is displayed.
Attaching a Photo to an E-mail Message Perform the procedure from step 1 to 2 under “Shooting a Photo” (page 61), and then perform the following steps. Press & (E-mail), and then press 1 (E-mail). The photo you shot is stored in the “Photo Folder” in the Data Folder. Perform the procedure starting from step 2 under “Creating and Sending E-mail Messages” (page 50) to create an e-mail message. Camera You can attach any photo you have shot to an E-mail, but data over 500KB cannot be sent.
EZweb EZweb subscription required Using EZweb To use EZweb, you need to subscribe to an EZweb beforehand. If you did not subscribe when you purchased your phone, contact your nearest au shop or the au Customer Service Center. In addition to an EZweb subscription, you also need to perform an initialization procedure before you can use EZweb. If you have not performed initialization yet, refer to “Initializing E-mail and EZweb” (page 24).
Displaying the au one Top While the standby screen is displayed, press R, use s to select “EZweb,” and then press 1 (au one Top).
Bookmarking Sites You Frequently Access Display a site you want to bookmark, and press % (BrowserMenu). Press 1 (New bookmark). ※ You may not be able to bookmark some sites. Press % (Reg). The message “Registered to Bookmark” appears when registration is completed. You can store up to 100 sites in the Bookmark(s).
L Viewing a Bookmarked Site ’s go et re! he While the standby screen is displayed, press R. Use s to select “EZweb,” and then press 2 (Bookmark(s)). Use j to select a site or folder, and then press c (Connect/Select). Checking Charges EZweb If you selected a folder, use j to select a site, and then press c (Connect). You can check call and transmission charges. While the standby screen is displayed, press c11. When the EZweb connection confirmation screen appears, press 1 (YES).
Downloading Chaku-Uta®/ Chaku-Uta-Full® To download a Chaku-Uta®/Chaku-Uta-Full®, perform step 1 under “Displaying the au one Top” (page 65), and then perform the following steps. Use j to select “カテゴ リ検索” (Search by Category), and then press c (OK). Use j to select “着うた フル・ビデオクリップ” (Chaku-Uta-Full® and Video Clip) or “着うた” (Chaku-Uta®), and then press c (Select). Select the content (desired information site), and download it.
EZweb In addition to transmission charges, you will be charged according to the pricing policy of each site to download Chaku-Uta®/Chaku-Uta-Full® and other contents from a fee-based site. ◎ Perform the same procedure to download wallpaper and use it for the standby screen background. ◎ You also can access an information site where you can download ChakuUta-Full® by pressing R while the standby screen is displayed, using s to select “LISMO,” and then pressing 2 (Jump to au one Music).
EZ News Flash/au one Gadget EZweb subscription required EZ News Flash displays a scrolling ticker showing the latest news on the standby screen, and you can view information by selecting it. au one Gadget displays an application called gadget on the standby screen. EZ News Flash/au one Gadget is available just after making initial settings for EZweb (page 24). All EZ News Flash information is distributed for no charge.
Setting EZ News Flash service You can use EZ News Flash with simple settings for no charge. Refer to “Initializing E-mail and EZweb” (page 24), complete initializing, and then make settings for EZ News Flash. Press u in the standby screen, select the ticker and press c (OK). Press j to select “はい” (Yes), press c (選択)(Select), Press j to select “OK,” and press c (Select).
EZ Navi EZweb subscription required EZ Navi Features EZ Navi uses global positioning system (GPS) information to provide you with useful information. Use s to select “ EZnavi.” Press R. Standby screen EZweb menu EZ Navi menu Checking your route: Passenger Seat Navi Passenger Seat Navi makes it possible for the passenger (non-driver) in a motor vehicle to check route information to a destination using both voice and map guides.
EZ Navi Walk A menu of useful options you can use while you are out. ナビをする★ (Navigation) Searchable source of a route guidance (voice navigation) to your destination, shops, and facilities 地図を見る (free)★ (View Map) You can view a map of your current location or any other location. 乗換検索する (free※1)★ (Search Connection) Searchable source of train transfer and timetable information 道路情報を見る (View Traffic Info) Check real-time traffic information on the major roads all over Japan.
◎ All display information is intended for reference purposes only. Be sure to follow all instructions issued by police, fire department personnel, government officials, etc. ◎ Due to GPS satellite conditions and other factors, it may take some time for Evacuate Navi to indicate your current location. ◎ The display layout and contents shown here are for example purposes only. ◎ Depending on the number of records stored in your address book, it may take some time for map viewer to start up.
au Media Tuner EZweb subscription required au Media Tuner makes it possible to enjoy using Television (1Seg) and EZ Channel-Plus. au Media Tuner Features With au Media Tuner, you can switch between television operation screen/data operation screen and enjoy Television (1Seg) of terrestrial digital audio broadcasts. &(Vol/Ch) &(戻る)(Back) Data operation screen Television operation screen ※ By switching the channel using L and R, registered EZ Channel-Plus programs will be displayed.
■ Using the built-in TV antenna When viewing with Television (1Seg), take care to avoid covering the built-in TV antenna with your hand in order to ensure proper reception. Built-in TV antenna ◎ You need to perform an initialization procedure before you can use au Media Tuner. If you have not performed initialization yet, refer to “Initializing E-mail and EZweb” (page 24). ◎ No call charge or packet communication fees are charged for using au Media Tuner.
Configuring au Media Tuner Initial Settings Perform the following procedure before using au Media Tuner for the first time. While the standby screen is displayed, hold down g for at least one second. Escape clause is displayed. If you select “OK (以後表示しない)” (OK (Do not display again.)), the display will not appear in the future. Use j to scroll the screen to read its contents. After you do, use j to select “OK” and then press c(選択) (Select).
◎ You may run into problems when configuring channel settings in step 3 in areas where 1Seg terrestrial digital television broadcast for cellphone/ mobile service has just started. ◎ Whenever you start up au Media Tuner, the channel you were viewing the last time you used it will appear first. If you move to a different viewing area and are unable to receive the currently configured channels, reconfigure channel settings.
Using Television (1Seg) While the standby screen is displayed, hold down g for at least one second. You need to perform an initialization procedure before you can use au Media Tuner. If you have not performed initialization yet, refer to “Configuring au Media Tuner Initial Settings” (page 77). When you start up au Media Tuner after configuring initial settings, the channel of the mode you were viewing the last time you used will appear. Use L and R to change the channel.
■ To switch between the earphone and speaker a On the television operation screen/data operation screen while au Media Tuner is running, press % (機能) (Function). b Use j to select “音声設定” (Sound Settings) and then press c (選択) (Select). c Use j to select “出力先” (Sound Output Settings) and then press c (選択) (Select). d Use j to select “オート” (Auto), “スピーカー ” (Speaker), or “イヤホン” (Earphone), and then press c (設定) (Set). The initial setting is “オート” (Auto).
Exiting au Media Tuner Press F, use j to select “はい” (Yes), and then press c (OK).
Other Functions Security Setup Features With Security Setup, you can make a phone call to preregistered numbers or use high-volume buzzer just by holding down 0 for at least one second. Safety Buzzer You can use W62CA as high-volume emergency buzzer by holding down 0 for at least one second while the standby screen is displayed. ■ To turn on Safety Buzzer While the standby screen is displayed, press c591, input the lock No., and then press c (OK).
In addition to the functions covered in this Basic Manual, your W62CA also has the following features. Global Passport GSM W62CA supports Global Passport GSM based on au IC-Card. Global Passport GSM is an international roaming service for the customers to use the phone replacing its au IC-Card with GSM cellphone for overseas use. No special application procedure or daily/monthly fee are needed, and the call charge is added up to domestic call, so the pay procedure is simple.
Troubleshooting Symptom What to check The phone does not turn on. Is the battery pack installed correctly? Is the battery pack charged? Are you holding down F for at least 2.5 seconds? (Out of Range) on Is the display? I can’t make calls. Are you including the area code? Is the phone turned on? Did you press N? Is Emission OFF Mode turned on? Is (Out of Range) on the display? I can’t receive calls. Nothing happens when I press the keys. The phone emits a warning tone, and then turns off.
If you lose your W62CA Setting Remote Ctrl Lock makes it possible to perform a remote operation that activates Auto Lock, FeliCa Lock and Address Book Lock to lock the W62CA. This helps to avoid unauthorized use of your phone and its features. ■ Configuring operating environment settings for Remote Ctrl Lock Repeatedly calling the W62CA from a pre-registered telephone number a specified number of times within a specified amount of time will activate Auto Lock, FeliCa Lock and Address Book Lock.
Press 3 (No. of Incm), input the number of calls you want to specify, and then press c (Set). You can set how many times you should repeat making a call to activate Remote Ctrl Lock. You can set it from 3 to 10 times. Press % (Save).
■ Using the Security Lock Service to activate Remote Ctrl Lock With the Security Lock Service, you can activate Auto Lock, FeliCa Lock and Address Book Lock remotely by placing a call to an au Customer Service Center or with your computer even if Remote Ctrl Lock is not set beforehand. The Security Lock Service is free. Using the Security Lock Service ● Calling an au Customer Service Center to activate or deactivate Remote Ctrl Lock On an au phone, dial 113 (free).
Index A Address Book ..................................... 41 Adding outgoing or incoming history data to the address book .............. 44 Deleting ............................................ 42 Dialing from the address book .......... 45 Editing............................................... 43 Registering ....................................... 41 Adjusting the earpiece volume ......... 35 Adjusting the ringtone volume ......... 34 Answering a call ................................. 30 Answer Memo .....
L Looking up your phone number ....... 25 M Mail ...................................................... 48 C-mail ............................................... 49 E-mail ............................................... 48 Mail filter ......................................... 5, 55 Main menu .......................................... 20 Making a call ....................................... 28 Making an international call .............. 29 Manner Mode ......................................
For inquiries, call: au Customer Service Center From EZweb site: How to access EZ→au one Top→auお客さまサポート (au Customer Support) →お問い合わせ (Inquiries) ※Menu structure is subject to change without notice. General Information, Rate Information From regular phones: (toll free) From au cellphones: area code not required (toll free) In case of loss, theft, or malfunction...
