E Handheld Printer Terminal Series User’s Guide Be sure to read “Safety Precautions” inside this guide before trying to use your Handheld Terminal. After reading this guide, keep it in a safe place for future reference. For product detail, refer also to http://world.casio.com/ system/pa/UsersGuide/ sup85_e.
• This Product is equipped with the Brycen B-RAPPORE Stack and My Wirefree Network Bluetooth User Interface Application, the use of which is governed by a license granted by Brycen Co., Ltd. ® • BLUETOOTH is a registered trademark owned by Bluetooth SIG, Inc. and licensed to CASIO COMPUTER CO., LTD. • Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. • Datalight is a registered trademark of Datalight, Inc.
Safety Precautions Congratulations upon your selection of this CASIO product. Be sure to read the following Safety Precautions before trying to use it for the first time. Your neglect or avoidance of the warning and caution statements in the subsequent pages causes the danger of fire, electric shock, malfunction and damage on the goods as well as personal injury. Markings and Symbols The following are the meanings of the markings and symbols used in these Safety Precautions.
Safety Precautions Warning Dust and Moisture • Though the Handheld Printer Terminal is dust and water splash resistant, its options including the battery pack are not. Keep loose metal objects and containers filled with liquid away from your Handheld Printer Terminal and the options. Also, never handle the Handheld Printer Terminal and the options while your hands are wet. Laser Light • This product with the integrated laser scanning module scans bar codes using laser light.
Caution Printer • Do not touch the areas around the printer motor or head since they can become very hot. Doing so can cause burns. • Touching any of the gears while they are turning with unprotected hands can cause personal injury. Be careful not to come in contact with turning gears. • Contact with the blade installed in the paper outlet can cause personal injury. Be careful not to touch the blade.
Safety Precautions Lithium-ion Battery Pack Danger • Never use the Handheld Printer Terminal and its option including the battery pack and battery next to open flame, near a stove, or any other area exposed to high heat, or leave them for a long period of time in a vehicle parked in direct sunlight. • Never use the battery pack with any device other than the Handheld Printer Terminal. • Never dispose of the battery pack by incinerating it or otherwise expose it to heat.
Power Supply / AC Adaptor Warning • Do not use the Handheld Printer Terminal at a voltage other than the specified voltage. Also, do not connect the Handheld Printer Terminal to a multi-plug power strip. • Never modify, sharply bend, twist, or pull on the power cord. • Never use a detergent to clean AC adaptor and its power cable, especially on the plug and the jack. • When using the battery charger and Bridge Satellite Cradle, be sure to use the respective AC adaptors.
Safety Precautions Backup Copies of All Important Data Caution • Note that CASIO Computer Co., Ltd. shall not be held liable to you or any third party for any damages or loss caused by deletion or corruption of data due to use of the Handheld Printer Terminal, malfunction or repair of the Handheld Printer Terminal or its peripherals, or due to the batteries going dead.
Operating Precautions Your Handheld Printer Terminal and its options are precision digital instruments. Improper operation or rough handling can cause problems with data storage and other problems. Note and observe the following precautions to ensure proper operation. • Do not leave dead batteries in the Handheld Printer Terminal for a long period. Dead batteries can leak, leading to malfunction and damage to the Handheld Printer Terminal.
Important • This guide does not include any information about programming and download procedures. See the applicable separate documentation for information about the procedures. After Service • Should this product ever malfunction, contact your original retailer providing information about the product name, the date you purchased it, and details about the problem. This mark applies to EU countries and Turkey only.
Regulatory Information The USA and Canada GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THIS UNIT IN THE U.S.A. (not applicable to other areas). NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Regulatory Information L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes : (1) il ne doit pas produire de brouillage et (2) I’utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.
Contents Safety Precautions ......................................................................................... E-1 Operating Precautions ................................................................................... E-7 Important ......................................................................................................... E-8 After Service ....................................................................................................... E-8 Regulatory Information ...............
Before Getting Started Be sure to perform the following steps before trying to use the Handheld Printer Terminal for the first time. 1. When unpacking, make sure that everything is included. Open the box and make sure that all the items shown here are included. Handheld Printer Terminal PC Card Remover (2 pcs) Handheld Printer Terminal n Stylus Neck strap and stylus holder Hand strap Neck strap rings Roll paper* Battery pack 58mm Paper Width Adjuster* PC card fixers User's Guide (this manual) 2.
3. Load the battery pack into the Handheld Printer Terminal. 1 Turn the battery pack cover lock switch on the side of the Handheld Printer Terminal to the “FREE” position. 2 Open the battery pack cover. 3 Install the battery pack(DT-9723LIC). Push it all way to the end inside the compartment until the eject button at the front of the battery compartment comes up (and sounds). Make sure the battery pack is aligned correctly when you install it.
Handheld Printer Terminal System Configuration Options IT-3100 Series Bridge Satellite Cradle HA-B61IO Cradle-type Battery Charger HA-B30CHG Required AC Adaptor for Bridge Satellite Cradle / Cradle-type Battery Charger AD-S42120BE AD-S42120B-N E-14
AC Cord for Europe AC-CORD-EU AC Cord for North America AC-CORD-US AC Code for Taiwan AC-CORD-TW AC Code for Korea AC-CORD-KR AC Code for Australia AC-CORD-AU Battery Pack DT-9723LIC Paper Holder* HA-B93PH Splash Protect Cover* HA-B92PCV * Not available for IT-3100M75E.
Handheld Priter Terminal System Configuration Screen Protect Cover* HA-B90DCV AC Adaptor AD-S10095AE AD-S10095AU Cables DT-887AXA DT-888RSC DT-380USB HA-B80AX Dsub 9-Pin (Female) RS-232C Cross Cable for Bridge Satellite Cradle RS-422 Modular Cable for connecting Bridge Satellite Cradle USB Cable for connecting Bridge Satellite Cradle and PC RS-232C Cross Cable for connecting Handheld Printer Terminal and PC * Not available for IT-3100M75E.
General Guide IT-3100 3 17 1 2 7 8 24 9 10 4 5 6 23 11 18 12 25 13 14 19 15 20 18 16 22 21 * The above illustrations show a model with C-MOS Imager and Magnetic Card Reader installed.
General Guide 1 SD Memory Card Slot 2 Program Key (L) 3 Roll Paper Holder 4 Splash Protect Cover and Paper Cutter 5 Power Key 6 Indicator 1 (Left Side) Indicator 2 (Right Side) 7 Speaker 8 Brightness Sensor 9 LCD Panel/Touch Screen 10 Stroke Keys 11 RS-232C Interface Connector (IT-3100M53E/M54E) 12 Program Key (R) 13 Power Jack 14 IR Port 15 Battery Pack Cover Lock Switch 16 Battery Pack Cover 17 PC Card Slot 18 Hand Strap Hook 19 14-pin Serial Interface Connector 20
Key Functions 1 Fn Key This key is used to switch the character input mode or make various settings in combination with other keys, or start up a pre-registered application. 2 Numeric Keys These keys are used to input numbers and letters. 3 (Cursor Key) Moves the cursor to the left. 4 (Cursor Key) Moves the cursor to the right. This is also used to feed paper when pressed after pressing the Fn key when printing paper is loaded. 5 - This key is pressed when inputting a hyphen or bar. 6 .
Replacing the Battery Your Handheld Printer Terminal uses two types of battery: a battery pack and a memory backup battery. A battery pack (DT-9723LIC) is used for the main battery. A backup battery is housed inside the Handheld Printer Terminal. This guide uses the following terms to refer to the batteries.
To replace the battery pack 1. Make sure that the Handheld Printer Terminal is turned off. If the power is on, press the power key to turn it off. 2. Turn the battery pack cover lock switch on the side of the Handheld Printer Terminal to the “FREE” position. 3. Open the battery pack cover. 4. Remove the battery pack. Press down the battery pack eject button (see the arrow). Remove the battery pack by pulling on the tape. 5. Install a charged battery pack in the Handheld Printer Terminal.
Replacing the Battery 6. Return the battery pack cover to its original position as shown in the illustration, and then turn the battery pack cover lock switch to the “LOCK” position. Important! • When replacing the battery pack, make sure you do not leave the Handheld Printer Terminal without a battery pack for more than about 10 minutes. Doing so can cause data in the memory to be deleted. • Never try to use other type of battery than the one that is specified for this product.
Attaching the Hand Strap A flexible hand strap can be attached to the Handheld Printer Terminal. Hook A Hook B Hand Strap Attach the hand strap following the procedure described below. 1. Attach Hook B of the hand strap to the hand strap hook located on the bottom of the Handheld Printer Terminal. 2. Pull on the hand strap in the direction shown in the illustration, and then fasten Hook A onto hook ( 1 ) on the back of the Handheld Printer Terminal. 1 1 3.
Attaching the Neck Strap A neck strap can be attached to the Handheld Printer Terminal to keep it from being dropped while being carried. The stylus holder provided can also be attached. Neck strap rings* Adjust length here Stylus holder Mounting hooks Neck strap Attach the neck strap following the procedure described below. Attachment Procedure 1. Pull out the neck strap mounting hooks out of each silo on the bottom of the Handheld Printer Terminal using the tip of stylus.
Removal Procedure 1. Pull back the locking bar of the neck strap mounting hook and then release the hook from each ring as shown in the illustration. 2. Following the attachment procedure in reverse way, remove the neck strap rings from each neck strap mounting hook on the Handheld Printer Terminal and then push back the neck strap mounting hooks into each silo. Attaching the Stylus Holder The stylus holder provided can be attached to the neck strap as necessary.
Attaching the Neck Strap 2. Remove Mounting Hook C. 3. Pass the stylus holder through the strap as shown in the illustration. 4. Fold back the strap after passing through Bracket C, and then fasten in the same way it was originally fastened with Bracket A and Bracket B. • Do not pass the strap through the stylus holder when folding it back. • Place the stylus in the stylus holder after first re-attaching the neck strap to the Handheld Printer Terminal.
Configuring Handheld Printer Terminal Settings Calibrating Touch Screen Alignment Whenever you feel that touch screen response is poor or that the operations being executed do not match the location you are tapping on the touch screen, perform the following operations to calibrate the alignment of the touch screen. • Press the “Fn” key and then make sure that “F” appears in the lower right corner of the screen. If the “F” appears, press the “4” key.
Using the Printer The printer can print on roll paper (80 mm or 58 mm wide)* or 80 mm wide formed sheet paper. When printing on formed sheet paper, use the paper holder (HA-B93PH) sold separately. When Using Roll Paper Installing the Roll Paper 1. Check that the power is off. If the power is on, always make sure to turn it off by pressing the power key. 2.
5. Close the roll paper holder, slide the lock knobs on the left and right sides as shown in the illustration to align at the “LOCK” position to lock the roll paper holder in position, and then tear off the protruding roll paper. • Please note that the positions of the lock knobs on the left and right sides are different. LOCK FREE 1 2 FREE 2 LOCK 6. Close the splash protect cover as necessary. • Open the splash protect cover when printing with the printer.
Using the Printer Attaching the 58 mm Paper Width Adjuster Attach the 58 mm Paper Width Adjuster* inside the roll paper holder when using 58 mm wide roll paper. Refer to the procedure described in “Installing the Roll Paper” for information on opening and closing the roll paper holder. 1. Remove the 80 mm Paper Width Adjuster as shown in the illustration. • Store the 80 mm Paper Width Adjuster in a safe place after it has been removed. 2.
Warning Label IT-3100M55U/M56U/ M55E/M56E Laser light is emitted from this port • This label is a warning label for Class 2 laser products that comply with IEC60825-1+A2:2001 CAUTION • Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. • The laser light emitted by the C-MOS Imager has a maximum output of less than 1 mW and a wavelength of 650 nm. Warning! Never look directly into the laser light.
Magnetic Card Reader The Magnetic Card Reader comes as standard with IT-3100M54E/M55E/M55U/M75E. Only use cards that are compatible with the ISO standards. The procedure for reading cards is described below. 1. Remove the cover as shown in the illustration. 2. Insert the card all the way into the reader as shown in the illustration, and steadily pass the card through the reader in the direction of the arrow.
Resetting the Handheld Printer Terminal Resetting the Handheld Printer Terminal is the same as restarting a computer. Performing a reset causes all unsaved inputs and edits to be lost, but data that is already stored in the memory as well as all settings should be unaffected. Use reset to restore normal operation whenever the Handheld Printer Terminal operates abnormally due to misoperation or some other reason. Use the stylus to press the reset switch on the back of the Handheld Printer Terminal.
Resetting the Handheld Printer Terminal Performing a Full Reset (Initialization) Performing a full reset initializes memory. This means that all data stored in the memory (RAM) is deleted and all the settings are returned to their initial factory settings. Perform a full reset whenever any one of the following conditions exists. • When you want to delete all memory contents and return the settings to their initial factory settings.
Charging the Battery Pack The following two methods, “Using the Cradle” and “Using the AC Adaptor (ADS10095AE/AU)”, show how to charge the battery pack. Before starting, the battery pack must be in the Handheld Printer Terminal.
Using PC Cards PC card compatible with the PCMCIA(Type I/II) standard can be installed in the PC Card slot on the Handheld Printer Terminal. Insert a PC card according to the procedure described below. Attaching the PC Card Removal Tape to a PC Card There are some PC cards that may be difficult to remove from the PC card slot once they have been inserted. In the case of such PC cards, attach the PC card removal tape provided before inserting the PC card.
4. Open the cover (PC card slot cover) as shown in the illustration. 5. Insert a PC card having PC card removal tape attached. Insert the PC card all the way in with the top of the card facing towards the top of the Handheld Printer Terminal. Fold up the end of the PC card removal tape so that it does not get caught in the way when closing the cover. 6. Attach the PC Card Holder to lock the end of the PC card and prevent it from coming out due to impacts and so forth.
Using SD Memory Cards SD memory card can be installed in the SD Memory Card slot on the Handheld Printer Terminal. Insert (or remove) an SD memory card according to the procedure described below. Inserting an SD Memory Card 1. Check that the power is off. If the power is on, always make sure to turn it off by pressing the power key. 2.
CASIO COMPUTER CO., LTD. 6-2, Hon-machi 1-chome Shibuya-ku, Tokyo 151-8543, Japan Printed on recycled paper.
