E Handheld Terminal Series User’s Guide Be sure to read “Safety Precautions” inside this manual before trying to use your Handheld Terminal. After reading this manual, keep it in a safe place for future reference.
Operating Precautions Your Handheld Terminal is a precision digital instrument. Improper operation or rough handling can cause problems with data storage and other problems. Note and observe the following precautions to ensure proper operation. • Do not continue operating the Handheld Terminal when battery power is low. Doing so can cause data to be lost. When batteries go low, charge them as soon as possible. • Do not leave dead batteries in the Handheld Terminal for long periods.
Introduction • The contents of this manual are subject to change without notice. • Note that CASIO COMPUTER CO., LTD. shall not be held liable to you or any third parties for any losses or damages arising from the use of this manual. • This manual does not include any information about programming and download procedures. See the applicable separate documentation for information about these procedures. Warranty and After Service • This product comes with a warranty certificate.
CASIO Europe GmbH Bornbarch 10, D-22848 Norderstedt, Germany Please keep all information for future reference. This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undersired operation. GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THIS UNIT IN THE U.S.A. (not applicable to other areas).
We, the undersigned.
Contents Safety Precautions ......................................................................................... E-1 Operating Precautions ................................................................................... E-8 Introduction .................................................................................................... E-9 Before Getting Started ................................................................................. E-14 Handheld Terminal System Configuration .............
Using the Satellite Cradle (DT-160IOE) ....................................................... E-34 General Guide ................................................................................................... E-34 Bundled Items ................................................................................................... E-34 Connecting the Satellite Cradle AC Adapter and Connecting to a Computer .. E-36 Configuring DIP Switch Settings ..............................................................
Before Getting Started Be sure to perform the following steps before trying to use the Handheld Terminal for the first time. 1. When unpacking, check to make sure that everything is included. Open the box and check to make sure that all of the items shown here are included. Handheld Terminal Stylus Fn BL ABC DEF GHI JKL MNO PQRS TUV WXYZ BS Alpha Large-capacity Battery Pack Cover Hand Strap PC Card Remover Tape (2) User's Guide (this manual) Warranty 2. Charge the battery pack.
2 Load a battery pack (DT-5023BAT) or a large-capacity battery pack (DT-5025LBAT). Take care that the battery pack is oriented correctly when you load it. 3 Replace the battery pack cover, and then slide the battery pack cover lock switches to the “LOCK” position. If you load a large-capacity battery pack, affix the largecapacity battery pack cover. 4. Hold down the power key for about one second to turn on the Handheld Terminal. Start up the application you want to use.
Handheld Terminal System Configuration Optional Accessories Satellite Cradle DT-160IOE Bundled Items AC Adapter (AD-S42120AE) DT-X10M30E DT-X10M20E DT-X10M20U DT-X10M30U Cradle-type Battery Charger DT-169CHGE Bundled Items AC Adapter (AD-S42120AE) Fn BL ABC DEF GHI JKL MNO PQRS TUV WXYZ BS Alpha Wall Mount Unit Wall Mount Unit Wall Mount Unit Screws Screws E-16
Battery Pack DT-5023BAT (Battery Pack) DT-5025LBAT (Large-capacity Battery Pack) Dual Battery Charger DT-5022CHGE Dual Battery Charger AC Adapter MPC-577ADP MPC-177ADP E-17
CF Card Extension Unit DT-894CFU Bundled Items Large Card Cover Cables DT-882RSC DT-883RSC DT-887AXA DT-888RSC DT-380USB Satellite Cradle – PC Connection Cable (RS-232C) Satellite Cradle – PC Connection Cable (RS-232C) Satellite Cradle – PC Connection Cable (RS-232C) Satellite Cradle Daisy Chain Cable Satellite Cradle – PC Connection Cable (USB) SB-201 PC Connection Cable (USB) E-18
General Guide Left Side Front 14 Right Side 1 2 Back 20 15 21 3 16 22 4 18 18 5 6 Fn 17 13 12 BL ABC DEF GHI JKL MNO PQRS TUV WXYZ BS 7 Alpha 10 23 17 8 9 11 19 1 Indicator 1 Lights green to indicate normal barcode or other data reading. 2 Indicator 2 Lights green to indicate charging is complete. 3 LCD Panel/Touch Screen Shows text, operation indicators, etc. Also, operations can be performed and text can be input using the supplied stylus.
11 IR Port This port is used for IR data communication with another Handheld Terminal or the Satellite Cradle. 12 CLR Key Press to clear all key input. 13 Fn Key Press this key and then a number key to access the function assigned to the number key. 14 PC Card Slot For insertion of a separately available PC card. 15 USB Port For connection of a USB cable. 16 Earphones Jack For connection of commercially available earphones (∅2.5mm).
Replacing the Battery Your Handheld Terminal uses two types of batteries: a main battery and a backup battery. The main battery is used to power normal operations and to store data, while the backup battery provides the power required to maintain memory contents when the main battery power is unable to supply power for some reason. The main battery is a battery pack. You can choose between a battery pack (DT-5023BAT) and a large-capacity battery pack (DT-5025LBAT).
To replace the battery pack 1. Make sure that the Handheld Terminal is turned off. If power is on, press the power button to turn it off. 2. Turn over the Handheld Terminal. 3. Slide the two battery pack lock switches on both sides of the Handheld Terminal to the “FREE” position, and then remove the battery pack cover. 4. Remove the battery pack as shown in the illustration. 5. Taking care to ensure it is oriented correctly, load a new battery pack into the Handheld Terminal. 6.
Loading the large-capacity battery pack into the Handheld Terminal After loading a large-capacity battery pack, you need to use the special large-capacity battery pack cover in place of the standard battery cover. Attachment and removal of the large-capacity battery pack cover are the same as attachment and removal of the standard battery pack cover. Important ! • When replacing the battery, make sure you do not leave the Handheld Terminal without a main battery for more than about 10 minutes.
Attaching the Hand Strap Be sure to attach the hand strap and use it to protect against dropping the Handheld Terminal when carrying it around. To attach the hand strap 1. Pass the thin cord of the hand strap through the hand strap hole on the back of the Handheld Terminal. 2. Pass the other end of the strap (the part where you insert your wrist) through the loop formed by the thin cord. Important ! Do not allow the Handheld Terminal to swing around freely from the hand strap.
Configuring Handheld Terminal Settings Calibrating Touch Screen Alignment Whenever you feel that touch screen response is poor or that the operations being executed do not match the location you are tapping on the touch screen, perform the following steps to calibrate the alignment of the touch screen. 1. Press the “Fn” key and then press the “4” key. 2. On the touch screen, tap the “Start” button and then tap “Settings” on the menu that appears. 3. On the Control Panel, tap “Stylus”.
Display Auto Dimmer The display auto dimmer automatically lowers display brightness if you do not perform any operation for a specific amount of time. This helps to conserve battery power. You can use the following procedure to specify the amount of that should be allowed to pass before auto dimming is performed. 1. On the touch screen, tap the “Start” button and then tap “Settings” on the menu that appears. 2. On the Control Panel, tap “Contrast & Brightness”. 3.
Using the C-MOS Scanner 1. Tuen on the Handheld Terminal, position its barcode reader port near the barcode or 2-dimensional bar code, and then press a Trigger key. 2-dimensional bar codes Green light Red light 2. The Handheld Terminal LED emits light and reads the barcode. Indicator 1 (read operation indicator lamp) lights green when reading is successful. Barcode and 2-dimensional bar codes Reading Guide When you press a Trigger key, LEDs in the Handheld Terminal emit green and red light.
About the warning label • This label identifies the light source of the Handheld Terminal as a Class 1 LED under the JIS C 6802 standard. • A Class 1 LED momentarily emits strong light. Never look directly into the light emitted by the LED. • Never use the barcode reader for any purpose that is not expressly specified by the contents of this manual. Doing so is very dangerous. • The maximum output of the LED light is up to 1mW, and the wavelength is 650nm (255⁄8").
Performing Data Communication IR Data Communication IR data communication can be used to transfer data between two Handheld Terminals. When performing IR data communication, orient the IR ports of both Handheld Terminals so they are pointing directly at each other. The ports can be in direct contact with each other, or they can be separated by up to 1 meter (3'31⁄2") (up to 25cm (97⁄8") for 4Mbps data communication).
BluetoothTM Data Communication BluetoothTM protocol can also be used to transfer data between two Handheld Terminals. With BluetoothTM the two Handheld Terminals should be located within about three meters (9'103⁄8") from each other, as long as there is nothing blocking the path between them. Important ! Observe the following precautions to help ensure that data communication is successful. • Make sure the BluetoothTM devices are located within three meters (9'103⁄8") of each other.
Resetting the Handheld Terminal Resetting the Handheld Terminal is the same as restarting a computer. Performing a reset causes all unsaved inputs and edits to be lost, but data that is already stored in memory as well as all settings should be unaffected. Use reset to restore normal operation whenever the Handheld Terminal operates abnormally due to misoperation or some other reason. Use the stylus to press the reset button on the back of the Handheld Terminal. This starts the reset operation.
Performing a Full Reset (Initialization) Performing a full reset initializes memory. This means that all data stored in memory (RAM) is deleted and all Handheld Terminal settings are returned to their initial factory defaults. Perform a full reset whenever any one of the following conditions exists.
DT-X10 Specifications Model: CPU: Memory: OS: Display: Serial Port: DT-X10M30E, DT-X10M20E, DT-X10M20U, DT-X10M30U Intel® PXA250 Application Processor (300MHz max.) 32MB RAM; 32MB Flash ROM (FlashFX built in) Microsoft® Windows® CE NET, English Version 3.5-inch, 240 × 320-dot color 2-Way TFT LCD Interface: USB slave (Mini B5 Pin) Transfer Rate: 12Mbps (max.) IR Port: Interface: IrDA Ver. 1.1 Standard Synchronization: Asynchronous, frame synchronization Transfer Rate: Up to 4Mbps (max.
Using the Satellite Cradle (DT-160IOE) The optionally available Satellite Cradle (DT-160IOE) makes it possible to transfer system data and file data between the Handheld Terminal and a computer over an RS-232C connection or USB connection. You can also connect to the Satellite Cradle to charge the Handheld Terminal battery. An optionally available wall mount unit lets you mount the Satellite Cradle on a wall.
1 USB Port This port accepts connection of a USB cable for connection to a computer for transfer of system data and file data. Use of the USB port requires installation of a special driver on the PC. 2 RS-232C Port This port accepts connection of an RS-232C cable for connection to a computer for transfer of system data and file data. Use of the RS-232C port requires installation of a special driver on the PC. 3 RS-422C Port This port is used when connecting to another Satellite Cradle.
Connecting the Satellite Cradle AC Adapter and Connecting to a Computer Use the AC adapter that comes bundled with the Satellite Cradle to supply power to it. Always make sure that power is being supplied to the Satellite Cradle by the AC adapter before performing any type of data communication operation with the Handheld Terminal. The Handheld Terminal draws power via the Satellite Cradle during data communication. 1.
4. Turn on power. This causes the Satellite Cradle power indicator lamp to light red. 5. Making sure that their two IR ports come into contact with each other, place the Handheld Terminal onto the Satellite Cradle. This causes the Satellite Cradle power indicator lamp to light green. • If the system is operating normally and data communication is enabled, the system status indicator lamp lights green. • The communication indicator lamp flashes green when data communication starts.
Configuring DIP Switch Settings A bank for DIP switches is located on the bottom of the Satellite Cradle. You can change the on/off settings of the DIP switches to configure the Satellite Cradle to meet your needs. After you change DIP switch settings, the new settings do not go into effect until you turn the Satellite Cradle off and then back on again.
Using a Wall Mount Configuration The following procedure explains how to use the optional wall mount unit to configure the Satellite Cradle for a wall-mounted configuration. 1. Remove the screws on the bottom of the Satellite Cradle, and remove the desktop unit. Screws 2. Affix the wall mount unit to the bottom of the Satellite Cradle, and secure it in place with the wall mount unit screws. Screws 3.
5. Drive the other screw into the wall at the location where the lower hole is located. 6. Drive the upper screw and lower screw into the wall the rest of the way. To remove the Satellite Cradle from the wall 1. Loosen the upper screw and lower screw. 2. Raise the Satellite Cradle and remove if from the screws. Important ! • While the Satellite Cradle is mounted on a wall, be sure to check the wall screws periodically for looseness. Tighten them as required.
Daisy Chaining Multiple Satellite Cradles (DT-160IOE) You can daisy chain multiple Satellite Cradles by connecting the C-OUT port of the unit that is closer to the host computer to the C-IN port of the unit that is further from the host computer. RS-232C cable or USB cable To host computer Daisy chain connection cables (DT-888RSC) Important ! You can use optional daisy chain connection cables (DT-888RSC) to link up to eight Satellite Cradles.
Satellite Cradle (DT-160IOE) Specifications 1. IR Data Communication Interface: Protocol: Synchronization: Transfer Rate: 2. RS-232C Protocol: Synchronization: Transfer Rate: 3. RS-422 Protocol: Synchronization: Transfer Rate: 4. USB Protocol: Transfer Rate: 5. Power Supply Power Requirements: Power Consumption: Handheld Terminal Output: 6. AC Adapter Model: Input: Output: 7. Functions IR interface IrDA Ver. 1.
Using the Cradle-type Battery Charger The optionally available Cradle-type Battery Charger (DT-169CHGE) lets you charge the Handheld Terminal’s battery simply by placing the Handheld Terminal onto the cradle. An optional wall mount unit lets you mount the Cradle-type Battery Charger on a wall.
1 AC Adapter Jack Connect the bundled AC adapter here. 2 Wall Mount Unit Fastening Plate The holes in this plate accept screws that secure the wall mount unit in place. 3 Power Contacts Power is supplied to the Handheld Terminal via these contacts. 4 Power Indicator Lamp This lamp indicates the power status and the connection status of the Handheld Terminal.
Connecting the Cradle-type Battery Charger AC Adapter and Mounting the Power PC Terminal Use the special AC adapter that comes with the Cradle-type Battery Charger to connect to a power source. 1. After making sure that the Cradle-type Battery Charger power switch is turned off, plug the AC adaptor into the AC adapter jack on the back of the cradle. Power switch (OFF) 2. Next, plug the AC adapter into a power outlet. 3. Turn on power.
Using a Wall Mount Configuration To wall mount the Cradle-type Battery Charger, use the same procedure as that described for the Satellite Cradle (DT-5060IO) on page 39. Cradle-type Battery Charger (DT-169CHGE) Specifications Power Requirements: Output: 5V DC 1.
Using the Dual Battery Charger The optionally available Dual Battery Charger (DT-5022CHGE) lets you charge two battery packs at the same time.
1 Charge Indicator Lamp This lamp indicates the charge status of the battery pack(s). Off: Not charging Red: Charging Red Flashing: Battery pack problem Green: Charging complete 2 AC Adapter Jack Connect the AC adapter here. 3 Dual Battery Charger Connection Port Use this port to connect multiple Dual Battery Chargers to each other. 4 Connection Bracket Attachment Holes The connection bracket attaches here when you connect multiple Dual Battery Chargers to each other.
Charging a Battery Pack 1. Plug the separately available special AC adapter into a wall outlet. 2. Plug the other end of the AC adapter into the AC adapter jack of the Dual Battery Charger. 3.Taking care that the battery pack is oriented correctly, insert it into the Dual Battery Charger. This causes the Charge Indicator Lamp to light red, indicating that charging has started.
Connecting Multiple Dual Battery Chargers You can connect up to three Dual Battery Chargers. Doing so makes it possible to supply power to all Dual Battery Chargers using a single AC adapter. 1. As shown in the illustrations below, remove the connector covers of the Dual Battery Chargers you want to connect to each other. Connector cover 2. Connect the two Dual Battery Chargers as shown below. 3.
Dual Battery Charger (DT-5022CHGE) Specifications Model: DT-5022CHGE Charging: Charging System: Charge Time: Fixed-voltage (with current limiter) Approximately 2.
Using a PC Card Your Handheld Terminal supports use of PC cards. Use the following procedure to load and remove PC cards. Affixing a PC Card Remover Tape Once loaded, some PC cards may be difficult to remove from the PC card slot. Affixing a PC card remover tape to the PC card before you load it makes it easier to pull the card out of the slot later.
2. Remove the PC card slot cover. 3. Slide a PC card with a remover tape affixed into the Handheld Terminal. Make sure that the top surface of the card is facing in the same direction as the Handheld Terminal display. You will not be able to insert the card all the way into the slot if it is not oriented correctly. Be sure to fold the tab part of the remover tape affixed to the card so it is not damaged when you replace the card compartment cover. 4.
Using a CF Card Extension Unit The CF Card Extension Unit (DT-894CFU) supports use of CF Type I cards and Type II cards (3.3/15V). Bundled Items DT-894CFU Large Card Cover Use the procedure below to load and remove CF cards. Important ! • Installing some cards will make it impossible to close the card slot cover. When that happens, you can either use the Large Card Cover or you can use the Handheld Terminal and CF card without a card slot cover.
Loading a CF Card 1. Wipe the surfaces of the card so it is free of any dirt, dust, or oil. 2. Remove the screws that secure CF Card Extension Unit in place, and then remove the card slot cover. 3. Making sure that the top surface of the card is facing in the same direction as the Handheld Terminal display, slide the card into the slot. You will not be able to insert the card all the way into the slot if it is not oriented correctly. 4.
Using a Rechargeable Battery Pack Your Handheld Terminal supports use of two battery back types of different capacity. You can select the one that best suits your needs in terms of operating time, the type of options you need to use, etc. When using the large-capacity battery pack, you need to use the special large-capacity battery pack cover that comes with the Handheld Terminal. Important ! Store a battery pack in its special soft case whenever you are not using it.
Safety Precautions Congratulations upon your selection of this CASIO Product. Be sure to read the following Safety Precautions before trying to use it for the first time. Markings and Symbols The following are the meanings of the markings and symbols used in these Safety Precautions. Danger This symbol indicates information that, if ignored or applied incorrectly, creates the danger of death or serious personal injury.
Warning Foreign Objects • Should any foreign matter get into the Handheld Terminal, immediately turn off the power and contact your original dealer or an authorized CASIO service provider. Continued use creates the danger of fire and electric shock. Dropping and Damage • Should you drop the Handheld Terminal and damage it, immediately turn off the power and contact your original dealer or an authorized CASIO service provider. Continued use creates the danger of fire and electric shock.
Warning! • Do not perform wireless data communication operations on the Handheld Terminal or turn the Handheld Terminal off when boarding an aircraft. Radio waves emitted by the Handheld Terminal can interfere with the aircraft’s navigation system. Caution Foreign Objects • Take care to ensure that metal or combustible objects are not inserted into the openings of the Handheld Terminal. Such objects create the danger of fire and electric shock.
Optional Lithium-ion Battery Pack Danger • Never allow the battery pack to become wet with either fresh water or salt water. Water can create the danger of battery pack heat emission, explosion, and fire. • Never use or leave the battery pack next to open flame, near a stove, or any other area exposed to high heat. Doing so creates the danger of battery pack heat emission, explosion, and fire. • Never use the battery pack with any device other than the Handheld Terminal.
Warning • Never place the battery pack in a microwave oven or any other high-voltage device. Doing so creates the danger of battery pack heat emission, explosion, and fire. • Should the battery pack emit a strange odor or heat, change color or shape, or exhibit any other abnormal behavior, immediately stop using it. Continued use creates the danger of battery pack heat emission, explosion, and fire. • If the battery pack does not achieve full charge after the normal charging time has passed, stop charging.
AC Power Supply Warning • Do not use the Handheld Terminal at a voltage other than the specified voltage. Also, do not connect the Handheld Terminal to a multi-plug power strip. Doing so creates the danger of fire and electric shock. • Avoid conditions that can cause damage or breaks in the power cord. Do not place heavy objects on the power cord and keep it away from sources of heat. Any of these conditions can damage the power cord, creating the danger of fire and electric shock.
AC Adaptor Caution • The outer cover of the AC adaptor can become warm during normal use. • Take normal precautions against electric shock. • At leas once a year, unplug the AC adaptor from the wall outlet and clean any dust that builds up between the prongs of the plug. Dust built up between the prongs can lead to the danger of fire. Backup Copies of All Important Data Caution • Note that CASIO Computer Co., Ltd.
