Poolroom SHOWER DOOR Shower Door Installation Instructions CON Reversible For a Left or Right Door | | Please Do Not Return the Product to the Store. | | Contact us with any questions.
Poolroom SHOWER DOOR Model Specific Preparation A REQUIRED: 3/8” (10mm) Out-of-Plumb Adjustment within the Wall Profile; Verify threshold and walls with a level.
Grog SHOWER DOOR PACKAGE CONTENT PACKAGE CONTENT PART# DESCRIPTION QTY PART# DESCRIPTION QTY Magnetic Seal A Bottom Gasket 2 G Aluminum channel 1 B Door panel-1 1 H U channel 1 C Wall Jamb 1 [ Alu. Threshold 1 D Top Cover Cap 1 J Vertical Gasket 1 E Handle 1 K Hinge 2 Magnetic strip 1 L Door panel-2 1 N (OTE ~ Inspect all parts for missing prior to installation! AL Contact us for any part missing.
Poolroom SHOWER DOOR PACKAGE CONTENT HARDWARE CONTENT Wall anchor Screw || | @6x38mm ST4*30 Fitting ST4*10 | Wood 7 pcs 7 pcs PCs 7 pcs 2 pcs | & Additional spare parts are included. | 0 Inspect all parts for missing prior to installation! Note |Contact us for any part missing.
Grog TOOLS REQUIRED SHOWER DOOR Drill Bits Screw Driver Drill Level 3.2/6 dia.
Poolroom SHOWER DOOR SAFETY INFORMATION CAUTION Please carefully read the following important safety information before handling or installing this shower. There is a risk of serious injury while handling this product. To minimize these risks, please note: * Always wear safety glasses and gloves while handling. + Always follow the installation instructions. * Inspect glass for damage before installation.
Grog SHOWER DOOR Model Dimensions configuration dimensions: Product Height | Model width | Installation width | © (OPN) 30" 30" ~31 3/8" 22 17/32" « YN Jon 32" 32" ~33 3/8" 24 17/32" 3/8" 26 17/32" 3/8" 28 17/32" \ D eave jb Deeds jb Dis jb Dee [F3— —m—— adjustment 3" max| adjustment 1" max adjustment 1" max ‘adjustment 3" max Vol If vol I I If Vol I \ shower head shower head Left pivot NOTE Right pivot Website: This model is reversible for right or left-hand door installation.
Poolroom SHOWER DOOR Wall Jamb Installation . NOTE, with a level before marking the Confirm the Wall jamb is plumb location of the holes for drilling. Te ~ Tre ETN NOTE] | Center the Wall jamb (C) on the Threshold.
Grog SHOWER DOOR Wall Jamb Installation silicone the back of the Wall Profile Website: eo If a Stud is present behind the wall: drill a hole up to the stud, 7 | drill an pilot hole into the stud and NOTE | | use the ST4.0 x 30mm Pan Head Screws (bb) Stud is present behind the wall: drill a @1/4” (6mm) hole and insert the Wall Anchors (aa) and use the ST4.0 x 30mm Pan Head Screws (bb).
Grog Website: Door panel Installation noon Hotlink : + 1 302 336 8180 SHOWER DOOR The Door panel Profiles can be adjusted up to 3/8” within the Wall Jamb for overall width or to correct for out-of-plumb conditions within the model size. Screw them together after making final adjustments. See label. Pls follow the arrows to install the glass panel Place wood shimmed) onto the threshold to provide proper spacing beneath the door glass.
Grog SHOWER DOOR Glass-to-Glass Hinge Assembly Installation “| Ensure the orientation of both Hinge Assemblies are the same. Make sure the Hinge Assemblies (B) are square and flatly installed on the glass outside Double sides of hinge part install to the B door panel-1. To prevent glass-to-metal contact, confirm the gaskets are present between the Hinge Assemblies and the Door Glass.
Poolroom SHOWER DOOR Glass-to-Glass Hinge Assembly Installation Place wood shimmed) onto the threshold to provide proper spacing beneath the door glass. Make any final adjustments to the door so that it is level and plumb in the opening. NOTE outside | Ensure the orientation of both Hinge Assemblies are the same. Make sure the Hinge Assemblies (K) To prevent glass-to-metal contact, confirm the gaskets are are square and flatly installed on the glass present between the Hinge Assemblies and the Door Glass.
Grog SHOWER DOOR Magnetic strip Install to door panel-2 Magnetic v1 Seal 2 Aluminum channel U channel vO Keep flush Website: TN 1. Magnetic strip Install to door panel-2. NOTE | | 2. PutF,G,H together before fasten the glass Ne i 7 door,make all these parts keep flush.
Grog Fasten the door panel After final adjustments, drill @1/8” holes in the Wall Jap (C). Drill only through the first layer of the Door panel Profile and install the ST4.0x10mm Pan Head Screws (dd) using the Decorative Covers and Washers (cc) Drill Bit | | Lo PN. Keep f ST4X10mm Include the washers when Pan Head Screw installing the ST4.0x10mm Pan Head Screws (dd) and Decorative Caps (cc) . NOTE 13 Website: [EG oC \adjustment §" max SHOWER DOOR TTT Adjustment 1" max | Hotlink : + 1 302 336 8180
Poolroom SHOWER DOOR Determine the G & H position Pencil Put F,G,H together, keep flush, mark the position on the wall. Center the Magnetic Seal Aluminum channel(G) and U channel (H) on the Threshold.
Poolroom SHOWER DOOR U channel Installation eo If a Stud is present behind the wall: drill a hole up to the stud, TTT drill an pilot hole into the stud and / 5 | use the ST4.0 x 30mm Pan Head Screws (bb NOTE | or (bb) Stud is present behind the wall: drill a hole and insert the Wall Anchors (aa) and use the ST4.0 x 30mm Pan Head Screws (bb).
Poolroom SHOWER DOOR Magnetic Seal Wall Jamb Installation ST4X10mm Include the washers when Pan Head Screw installing the ST4.
Grog handle Installation NOTE | and open the door.
Poolroom SHOWER DOOR Top Cover Cap & Vertical Gasket Installation Attach the Vertical Gasket (J)to the inside edge of NOTE! the Door Glass that is on the same side as the shower head so that the flexible fin is pointing away from the water source.
Grog Bottom Gasket Installation SHOWER DOOR "X2"is from J to F. Led ~ ] 1 Measure "X" and 'NOTE | | cut the Bottom Gasket Se | same length as "X". "X1" is from pivot channel to glass edge.
Poolroom SHOWER DOOR Alu. Threshold Installation ass and NOTE | "X" wall to wall width. NOTE | cut the alu threshold NU same length as 27mm [1 1/16 ~~ | The large curved lip of the dam strip is NOTE | | intended to face toward the outside of | the shower to ensure the flow of water is redirected towards the drain.
Poolroom SHOWER DOOR SEALING NOTE | The surfaces need to be clean and free of debris before applying silicone. | 7 i Ensure that the Shower door closes tightly and opens smoothly. NOTE Apply a good quality silicone sealant along the wall Water seal Allow 24 hours for the silicone to cure before using the shower. Apply Silicone a supplied).
Poolroom SHOWER DOOR This troubleshooting guide is for general aid only. For service and installation issues or concerns, please contact us by email Troubleshooting Problem/Symptom Suggested Solution Page(s) *Check all shipping/packaging material for missing Co parts/components. Missing parts 2.3 *If not found, please contact us by hotlink + 1 302 336 8180 to order factory part replacement. *Check the magnetic seal (F)and pvc seal (J) for proper trimming and installation.