Table of Contents www.CasablancaFanCo.com What to Expect with Your Installation Tools Needed 1.888.227.
What to Expect with Your Installation www.CasablancaFanCo.com 1.888.227.2178 Read and Save These Instructions If you are unfamiliar with wiring, use a qualified electrician. This product conforms to UL Standard 507. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box Know your wiring You may need a friend to help you. Assess location 1 Ceiling angles greater than 34° will require an Angled Mounting Kit.
Tools Needed Ladder Screwdrivers www.CasablancaFanCo.com Pliers Power Drill (optional) Wire Strippers 9/64” Drill Bit (optional) If mounting to a support structure, you will also need these tools. 3 M8551-01 • 09/25/18 • © 2018 Casablanca Fan Company Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag. The symbols can be used to identify the appropriate hardware for each step. 1.888.227.
Preparation www.CasablancaFanCo.com ! KEEP DISC D AR Time Saver Tip: Get a helper to insert grommets, found in the hardware bag, into the blades while you’re doing the next couple of steps. Remove the shipping blocks from the motor. Save the screws. They will be needed for blade iron installation. Note: Some fans will have a shipping ring instead of shipping blocks. Please remove the ring and save the screws. 4 M8551-01 • 09/25/18 • © 2018 Casablanca Fan Company 1.888.227.
34O CEILING Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately). Angled Mounting Standard Mounting Style Ceiling Outlet Box (required) Use the three steps below to determine if your ceiling angle is greater than 34° 2 1 1.888.227.
Ceiling Bracket www.CasablancaFanCo.com 1.888.227.2178 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
Option 1 Downrod www.CasablancaFanCo.com 1.888.227.
Downrod (continued) KEEP! (not to scale) 8” & 3/8” 1.888.227.2178 STRIP CUT www.CasablancaFanCo.com ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. www.CasablancaFanCo.com DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 9 M8551-01 • 09/25/18 • © 2018 Casablanca Fan Company 1.888.227.
Wiring www.CasablancaFanCo.com Connect the black (ungrounded) wire from the ceiling to the black wire from the receiver. Ung Bla ck rou Connect the yellow wire from the receiver to the black wire from the fan. k ac nde Bl d Yello w Receiver 1.888.227.2178 Slide the remote receiver onto the top of the bracket. ed ite Wh ow Yell Green/ und Gro White /Yellow Turn the wires upward and push them carefully back through the hanger bracket into the outlet box.
Canopy www.CasablancaFanCo.com Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. Note: Fan style may vary. 11 M8551-01 • 09/25/18 • © 2018 Casablanca Fan Company 1.888.227.
Blades www.CasablancaFanCo.com Remember the screws that you kept after removing the shipping blocks (page 6)? You need them plus five more from the hardware bag for this step. Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade iron with screws found in the hardware bag. Lightly attach the blade irons to the motor with screws found in the hardware bag, then securely tighten after both screws are attached.
Switch Housing Screw two housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. www.CasablancaFanCo.com Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. 1.888.227.2178 Insert the third screw, found in the hardware bag, into place and then tighten all three screws.
Switch Housing (continued) Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. Make sure the lower switch housing is securely attached to the upper switch housing. Failure to properly secure all 3 assembly screws could result in the switch housing fixture falling. www.CasablancaFanCo.com Lift the lower switch housing up until the holes line up with the screw holes in the upper switch housing.
Wall Control For Single Switch www.CasablancaFanCo.com If you have a dual switch setup, go to page 18 for dual switch installation instructions. 1 Installing the Wall Plate Bracket 4 Wiring the Wall Control Snap the Wall Control into the Wall Plate Bracket. Turning off the power Ensure the power is OFF at the outlet box and wall switch location before proceeding with installation. n Tur 2 3 Installing the battery To access the battery compartment, slide the battery door up. er Pow OFF 1.
Wall Control For Single Switch 5 6 www.CasablancaFanCo.com 7 Installing the Wall Control Install the longer screws through the slots in the wall control into the switch box screw holes. Turning on the power IMPORTANT n Tur 8 Installing the Wall Plate Push the wall plate onto the Wall Plate Bracket. It should snap into place. 1.888.227.
Wall Control For Dual Switches www.CasablancaFanCo.com 2 To install the Casablanca Wall Control into a dual switch location, you will need a wall plate with both a standard switch and rocker switch cut-out (sold separately). If you are unfamiliar or uncomfortable with wiring, please contact a qualified electrician. (Sold Separately) 1 Installing the battery To access the battery compartment, slide the battery door up. Battery Door Replace the used battery with two AAA batteries when needed. 1.888.
Wall Control For Dual Switches 4 Remove the existing wall plate 5 Remove the Casablanca Wall Control frame. www.CasablancaFanCo.com 7 Remove the existing wall plate. Save the screws. You will need them for the existing, marked light switch. 6 8 Wiring the Casablanca Wall Control 1. 2. 3. 4. Install the Wall Plate Install the wall plate that fits your setup (sold separately). 1. Use the screws you saved to reinstall into the light switch. 2. Remove the frame from the Casablanca Wall Control.
Wall Control www.CasablancaFanCo.com KEY PRESS KEY PRESS FUNCTION FUNCTION LIGHT FUNCTIONS Long Press Long Press Long Press FAN FUNCTIONS Light On/Off Fan On/Off Light Dimming Control Fan Speed Control Long Press Long Press Light High Light Low + Dimming Mode On/Off Fan High Fan Low Long Press Fan Reverse Power On/Off Long Press 19 M8551-01 • 09/25/18 • © 2018 Casablanca Fan Company + Pair Function 1.888.227.
Troubleshooting www.CasablancaFanCo.com Fan doesn’t work Excessive wobbling Remote does not work • Press a fan speed buttons up or down. • Tighten all of the blade and blade iron screws until they are snug. • Make sure the battery is installed correctly. • Check the circuit breaker to ensure the power is turned on. • Check the wall control battery. • Make sure the blades spin freely.
Troubleshooting (continued) www.CasablancaFanCo.com Installing Multiple Fans with Independently Operating Remote Controls 1.888.227.2178 Installing One Fan Operating on Multiple Remote Controls To install multiple fans with independently operating remote controls, there is no need to perform any pairing procedures. Each set of receiver/transmitter is already paired. Simply install each receiver into a fan and use the appropriate transmitter to operate each fan.