User's Manual

ManualsBrandsCasablanca Fan ManualsElectronicsRemote control for ceiling fan

To control the fan and lights from two

locations (a three-way circuit), use two

W-74 wall controls.

1. Remove the screws and switch plate from

the existing switch box and the screws

holding the switch in the switch box.

2. Pull the existing switch from the switch

box to expose the wire connections.

3. Determine which wire is connected to the

common terminal from the power source

(120V AC) of the three-way switch. (The

terminal will be marked on switch).

4. Remove the wire from the common

terminal of the three-way switch.

Connect this wire to the remaining

black/white striped wire on the W-74

control. Secure this splice with a wire

nut.

5. Remove the two remaining wires

from the three-way switch. Connect

the black wire of these wires to

a black wire on the W-74 control.

Secure the splice with a wire nut.

The remaining red wire is to be

connected to the other red wire on the

W-74. Secure the splice with a wire

nut.

6. Connect the green ground wire coming

from the back of the W-74 control to the ground wire in the switch box. Secure the

splice with a wire nut.

7. Check your work by using the wiring diagrams as shown in Figure #5 on this page.

8. Install the W-74 in the wall box with the two long screws provided.

9.Install the wall plate with the two short color-matched screws provided.

10.Installation of the second W-74 control is identical. Repeat steps 1 through 9.

W-74 WALL CONTROL

INSTALLATION

(For use on product with BOTH UP and DOWN LIGHTS ONLY)

Setting the Frequency

DIP SWITCHES

(FIGURE #2)

To use this switch with an existing W-74 wall switch,

you must rst set the jumpers on the new switch to

match that of the existing one.

1. Turn off power to the existing wall switch.

2. Using a screw driver, remove the (2) wall plate

screws, then remove the (2) switch mounting

screws.

3. Gently remove the existing wall switch from the

wall and locate the dip switches located on the

side of the switch.

4. Change the dip switches on the new wall switch

to match the exisiting. (FIGURE 2)

5. Reinstall the existing wall switch.

inStalling the Wall control

The wall control installs in the same manner as an ordinary light switch, using an existing

wall box and wiring. This controller is designed to signal the fan microcomputer as well

as perform normal switching operations. For this reason the following precautions must

be observed:

1. Use only the Casablanca W-74 wall control.

2. Do not use any additional control with your Direct-Touch™ fan (for example, dimmer,

or fan speed control).

3. Do not use more than one fan per wall control.

4. No other light xtures or electrical appliances may be connected on the circuit con-

trolled by the W-74 wall control.

SINGLE W-74 INSTALLATION

CAUTION!

Ensure power is turned OFF at the breaker or fuse panel before starting

installation.

If you have multiple Direct-Touch

™

fans,

refer to the section "Channel Changing".

1. Remove the screws and switch plate

from the existing switch box.

2. Remove the screws holding the switch

in the switch box.

3. Pull the existing switch from the switch

box to expose the wire connections.

4. Remove the two wires from the switch.

5. Connect the BLACK wire from the

POWER SOURCE that you just removed

from the switch to the BLACK/WHITE

STRIP wire on the W-74 wall control. Secure this connection with a wire nut.

6. Connect the second BLACK wire that

you just removed from the switch to

the second BLACK wire on the located

on the back of the W-74 wall control.

Secure this connection with a wire nut.

7. Connect the green ground wire coming

from the back of the W-74 control to the

ground wire in the switch box. Secure

the splice with a wire nut.

NOTE: The RED wire is not used in

this application. DO NOT remove the

crimped cap from the wire.

8. Check your work by using the wiring

diagrams as shown in Figure #3.

9. Install the W-74 in the wall box with the two long screws provided.

10. Install the wall plate with the two color-matched screws.

DUAL W-74 INSTALLATION

To control the fan and lights from two locations (a three-

way circuit), use two W-74 wall controls as shown in

the wiring diagram in Figure #5. Before installing

the two switches into the wall, place both switches

side by side, then locate the 4 dip switches on the

side of the two switches. Then make sure that the

dip switches are set to the same address on both

switches as shown in Figure #4. When setting these

dip switches you are setting the channel number

that is required to control both your fan and lights

from both sides of the room. If you are installing

other Direct-Touch™ fans within your home you

may need to reset the dip switches on these other

fans to a different channel before installing your

W-74 wall control into the wall. Please review the

section on channel changing on this instruction

sheet.

channel changing

Each fan must operate on it’s own frequency to prevent interference. Fan frequencies

are set by the dip switch settings on the W-74 wall control (other than to match an

existing W-74 controlling the same fan). To synchronize the fan to the new frequncy:

1. Turn the power OFF to the fan and W-74 you want to synchronize.

2. Turn the power back on to the fan and W-74 wall control.

3. Within 20 seconds of restoring power to the ceiling fan and the W-74 Wall Control

press and hold both the “1” and

1 2

4 3

reverse buttons. For 3 seconds, you will hear

one tone from the Piezo Buzzer indicating the command has been accepted. The

Fan and Lights will be off.

CAUTION!

Ensure power is turned OFF at the breaker or fuse panel before starting

installation.

W-74 Wall control HardWare

Wall Plate

Screws (2)

Switch

Mounting

Screws (2)

(4) Wire Cap

W-74

Wall Control

Cover Plate

WARNING!

To avoid possible electrical shock, make

certain that electricity is turned off at

the circuit breaker or fuse box before

attempting any installation or repair

procedure

CAUTION! NOT turning the power

OFF at the circuit breaker or fuse box

may cause damage to the electronics

within the wall control and or the PC

board on the fan.

W-74 Wall control PreParation

Circuit Breaker

(Trip breaker for the

circuit you will be

working on)

Fuse Box

(Remove fuse for the

circuit you will be

working on)

BLACK AND WHITE

STRIPED WIRE

2 BLACK

WIRES

RED WIRE

NOT USED

(FiGUre #3)

(FIGURE #4)

DIP SWITCHES

BLACK

RED

GREEN

120V AC

BLACK

BLACK WITH

WHITE STRIPE

W-74

RED

BLACK WITH

WHITE STRIPE

GREEN

W-74

BLACK

NEUTRAL

WHITE

GREEN

(FIGURE #5)

W-74

Wall Control

BLACK AND WHITE

STRIPED WIRE

2 RED WIRES

2 BLACK

WIRES

(FIGURE #6)

W-74

Red

White

Blue

Black/White

Summary of content (2 pages)

PAGE 1
6. Connect the second BLACK wire that you just removed from the switch to the second BLACK wire on the located on the back of the W-74 wall control. Secure this connection with a wire nut. W-74 WALL CONTROL INSTALLATION (For use on product with BOTH UP and DOWN LIGHTS ONLY) 7. Connect the green ground wire coming from the back of the W-74 control to the ground wire in the switch box. Secure the splice with a wire nut.
PAGE 2
1 2 0 4 3 1 2 Operation 1 Operation Safe-Exit® 2 0 The power button is normally left in the on 0 position. Always turn the power off during cleaning or 4 servicing 3 the fan and during thunderstorms. It is also used to exit or enter additional programs. The power button must be left on to retain a previously set fan speed or light level. 4 1 2 The Safe-Exit Program gives you about thirty 0 seconds of light when you turn the lights off, enabling4 you to 3exit your home before the lights go out.