NOUVELLE OWNERS MANUAL
• The blades in each pack are matched for equal FUSE BOX (REMOVE FUSE FOR THE CIRCUIT YOU WILL BE WORKING ON) CIRCUIT BREAKER (TRIP BREAKER FOR THE CIRCUIT YOU WILL BE WORKING ON) 1
MOUNTING RECOMMENDATIONS Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mounting recommendations as you decide where to install your Casablanca fan. • For safety reasons, the fan blades must be a minimum of 7′ above the floor.
INSTALLATION INSTRUCTIONS Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed in instructions. Before discarding packaging material, be certain that all parts have been removed.
NOUVELLE™ ADAPTOR PLATE INSTALLATION JOIST Note: After removing the old fixture, check the outlet box to insure that it is supported by a joist or beam across its upper surface. If not, a 2" x 4" stud must be installed. Proceed with installation as follows: Step 1. Remove the knockout plug in the center of the outlet box or drill a 1/2″ hole for the lag screw to pass through. Then drill a 1/4″ guide hole into the joist or beam to a depth of 3″.
NOUVELLE™ CANOPY INSTALLATION Step 4. Attach the canopy to the cross bar with three (3) of the 8-32 X 41/8″ canopy screws and #8 lock washers, hand tighten until snug against the ceiling. On sloped ceilings, align the canopy hatch opening toward the top or peak of the room. Your Casablanca fan may be installed on a vaulted or cathedral ceiling in the same manner as described for a flat ceiling. The Hang-Tru® mounting system makes it possible to hang your fan on ceilings sloped up to a 32° angle.
6
7
BLADE HOLDERS & HARDWARE BLADE HOLDER BLADE HOLDER SCREW COUNTERSUNK PHILLIPS 12-24 X 5/8″ (2 PER BLADE) BLADE SCREW FLAT HEAD 10-24 X 7/16″ (4 PER BLADE) FELT WASHER #10 (4 PER BLADE) BLADE & BLADE HOLDER INSTALLATION Step 10. Attach the blades to the blade holders with four of the flat head 10-24 X 9/16″ blade screws and #10 felt washers provided. Hand tighten securely.
LIGHT FIXTURE ELECTRICAL CONNECTIONS Step 12. Remove the wire nuts on the BLACK and WHITE wires from the fan. If necessary remove the insulation from the last 1/2” of each wire (fan and light fixture). Step 13. Have an assistant hold up the light fixture until it is close to the adaptor ring. Step 14. Attach the switch housing wires to the light fixture wires by placing the bare ends of the wires together and then securing with a wire nut.
NOUVELLE™ LIGHT SHADE & BULB HARDWARE LIGHT SHADE FINGER SCREW (3 PER SHADE) 60 WATT BULB LIGHT SHADE & BULB INSTALLATION Step 16. Install three finger screws into each light fitter. Turn only once or twice. Step 17. Position the shade fully in the fitter and tighten each finger screw two turns each in rotation until the shade is centered in the fitter. Check that the shade is captured by the finger screws by lightly pulling on the shade. Hand tighten the finger screws securely. Repeat for each shade.
NOUVELLE™ NO LIGHT FIXTURE OPTION - HARDWARE LOWER SWITCH HOUSING CAP THREADED BUTTON NO LIGHT FIXTURE OPTION - HARDWARE ASSEMBLY Step 20. Line up the center holes of the cap and lower switch housing to allow the threaded button to be installed. Hand tighten securely LOWER SWITCH HOUSING LOWER SWITCH HOUSING CAP THREADED BUTTON NO LIGHT FIXTURE OPTION - INSTALLATION HARDWARE LIGHT FIXTURE SCREW PHILLIPS COUNTERSUNK 6-32 X 5/16″ (3) NO LIGHT FIXTURE OPTION - INSTALLATION Step 21.
The wall control installs in the same manner as an ordinary light switch, using an existing junction box and wiring. This controller is designed to signal the fan microcomputer as well as perform normal switching operations. For this reason the following precautions must be observed: 1. Use only the Casablanca W-32 wall control. 3. Do not use more than one fan per wall control. 2. Do not use any additional control with your Inteli-Touch 4.
R INTELI•TOUCH OPERATION ♦ POWER The button is normally left in the on position. Always turn the power off during cleaning or servicing the fan and during thunderstorms. It is also used to exit or enter additional programs. POWER must be left on to retain a previously set fan speed or light level. INTELI•TOUCH OPERATION ♦ SPEED CONTROL There are six individual speed settings for the fan; each speed is indicated by an audible tone of increasing pitch. To select the desired fan speed: 1.
The Light-Minder program automatically turns OFF the fan mounted lights after two hours. To enter the Light-Minder Program: 1. Turn the OFF for at least three seconds. ON. 2. Turn the 3. Immediately operate the buttons in the following sequence: + + + 4. A series of tones indicates this command has been accepted. The fan and light will operate normally using the buttons to turn them on and off. But, if the lights are left on, they will automatically shut off after two hours. To off for three seconds.
R TROUBLESHOOTING Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance. Caring for Finishes: For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish. A vacuum cleaner brush nozzle can remove heavier dust. Surface smudges or an accumulation of dirt and dust can easily be removed by using a mild detergent and slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents.
761 CORPORATE CENTER DRIVE • POMONA, CA 91768 TOLL FREE: 888-CASA-1ST (227-2178) www.CasablancaFanCo.com ©COPYRIGHT 2000 CASABLANCA FAN COMPANY • U.S.