Installation Instructions

ManualsBrandsCartell ManualsElectronicsCartell wireless - sensor

CW-SYS WIRELESS DRIVEWAY SYSTEM INSTALLATION INSTRUCTIONS*

1. WHAT’S IN THE BOX

There is a barcode serial number on the back of Integrator, boom of puck,

and on product box. When calling to talk about your product, please have one

of these numbers handy.

PRODUCT

CODE

YEAR

MADE

SERIAL

NUMBER

2. SERIAL NUMBER

1. SENSOR “PUCK”

2. INTEGRATOR

3. AUGER SCREWS (2)

4. CR123A BATTERIES WITH

CLIPS (2)

5. 3’ (1 m.) COAXIAL CABLE

6. TERMINAL BLOCK

SCREWDRIVER

3. INSTALLING BATTERIES/LOW BATTERY

1. Use CR123A baeries and match polarity with baery terminal in puck

2. If baeries are put in backwards, they will not make contact

3. Push baeries in place fully to make contact

4. Snap plasc baery holder over each baery and onto baery terminals

5. Sensor will power up automacally when baeries are installed

4. PAIRING

YOUR SYSTEM HAS BEEN PAIRED AT FACTORY.

THESE DIRECTIONS APPLY WHEN PAIRING

ADDITIONAL UNITS

6. TESTING RANGE

Your system has a radio range of at least 350 feet or over 1000’ line-of- sight.

To determine range in your applicaon, test before nal installaon.

Radio range depends on several variables:

• How the puck is installed (in ground or above ground on post)

• Obstacles blocking radio signal, such as soil, trees, foilage,

buildings, concrete, etc.

To test range:

1. Put Integrator near its nal installaon place in the home or gate

2. You will need to conrm the Integrator is sounding (see #9 below)

3. Put sensor in test range mode (see #5 above)

4. Listen for Integrator to trigger. If it doesn’t, move sensor closer to Integrator

5. Be sure to test again with puck installed in ground (see #8 below)

6. You may need to add a repeater inside the home (see #9 below)

5. TEST MODE FOR SENSOR PUCK

Test mode allows the sensor puck to automacally transmit the radio signal

without having to trip the sensor with a vehicle. This is useful when tesng

radio signal range (see #6 below).

1. Press and HOLD buon on sensor puck for 2 seconds

2. The red LED will blink every second when in test mode

3. There will be an immediate transmission

4. Addional transmions will occur every 10 seconds

5. Test mode will be exited when buon is pressed again for 2 seconds

6. Test mode will automacally be exited aer 30 minutes

8. INSTALLING SENSOR PUCK

WARNING: SCREW HOLES IN PUCK WILL STRIP IF SCREWS ARE TAKEN IN & OUT

REPEATEDLY OR OVERTIGHTENED WITH SCREW GUN. BE CAREFUL.

The sensor puck can be installed in the driveway, in the ground or on an

immovable object (post, tree, etc.).

ON AN OBJECT (see illustraon boom le)

1. When range has been tested (see #6 above), seat lid securely on puck with

screws provided. There should be no gap between lid and puck. Be careful not

to strip screws with screw gun. Finish ghtening by hand.

2. Find a tree, post, or other object directly beside the driveway

3. Make sure the object is IMMOVABLE or false alarms will occur

4. Use the holes on the boom tabs to screw puck to the object

IN THE GROUND (see illustraon boom le)

1. When range has been tested (see #6 above), seat lid securely on puck with

screws provided. There should be no gap between lid and puck. Be careful not

to strip screws with screw gun. Finish ghtening by hand.

2. Find a spot directly beside driveway

3. Dig a hole big enough for puck and auger screws, allowing puck’s lid to be

level with surface of dirt

4. Secure puck in ground with auger screws, overlaping boom tabs of puck.

If you fail to secure puck, lawn mowers, etc. will pull/suck it up.

5. Pack and tamp dirt around puck, ensuring lid is clean of dirt and all debris

IN THE DRIVEWAY (see illustraon boom le)

1. When range has been tested (see #6 above), seat lid securely on puck with

screws provided. There should be no gap between lid and puck. Be careful not

to strip screws with screw gun. Finish ghtening by hand.

Note: you may want to turn sensivity down (see #7 above)

2. Use a 4.5" diameter masonry hole saw to bore a hole for puck. Bore at least

2.75” deep so puck lid will be 1/4" below driveway surface (so it can’t be pulled

up by snow plows, graters, etc.)

3. Pour loop sealant in hole, careful not to overll, and put puck in hole

4. Hold puck down with weight unl sealant becomes rm

5. DO NOT pour sealant over puck lid or bosses as you will need access to

baeries

7. SETTING SENSITIVITY

ONLY ADJUST (LOWER) SENSITIVITY IF PUTTING IN MIDDLE OF

DRIVEWAY (see #8 below). IN ALL OTHER CASES USE DEFAULT.

SENSITIVITY ADJUSTMENT

HIGH (Default)

Detects vehicle going

5 MPH 12-14’ away

1 & 2 in OFF position

MEDIUM

Detects vehicle going

5 MPH 6-8’ away

1 ON & 2 OFF position

LOW

Detects vehicle going

5 MPH 2-3’ away

1 & 2 in ON position

1 2

Push buon to

put in

test mode

NOTE: DIP SWITCH

COLOR MAY VARY

2. Push pairing buon on Integrator

(will stay in pairing mode 30 minutes)

3. Power down

& power up

sensor by un-

installing and

re-installing

one baery

(see #3 above)

4. Integrator will beep 3 mes

when paired and exit pairing mode

automacally

You can pair up to 10 pucks with unlimited number of Integrators

1. Bring sensor close to Integrator

and power up Integrator

(see #10 below)

ON AN OBJECT IN THE GROUND IN THE DRIVEWAY

*Patent Pending

OPTIONAL

• 12VDC power

(Part #CW-PS)

supply

LOOP

SEALANT

1/4"

Don’t allow

sealant to

touch lid

or bosses

Fill line

Use 4.5” masonry hole saw

Pour

sealant

in hole,

then

install

puck.

Do not

cover

lid or

bosses

with

sealant.

• Put logo parallel to drive

• Put just below surface

• Auger screws secure puck

• Do not cover puck lid

• Pack dirt/grass around

puck

• Keep puck lid clean

min.

6"- 8"

• Use stable

object

• Use 4 deck

screws for

fastening

Bore hole

4.5" x 2.75" deep

WARNING: KEEP LID FREE OF DIRT, GRASS, SNOW, & ALL DEBRIS AT ALL TIMES TO ALLOW RADIO SIGNAL TO TRANSMIT!

NOTE: BE CAREFUL NOT TO STRIP PUCK SCREWS. SHOULD YOU DO SO,

PURCHASE LONGER SCREWS AT YOUR LOCAL HARDWARE STORE.

MAKE SURE THEY ARE STAINLESS STEEL AND SUITABLE FOR PLASTIC.

Pairing

Buon

LOW BATTERY

When baeries need replacing

in sensor, Integrator will “chirp”

and its LED will blink RED.

When hooked to external

system’s zone inputs (see #10

below), program what you desire

in order to indicate low baery.

Replace BOTH CR123A baeries

at the same me.

NOTE: HIGHEST SENSITIVITY IS WITH

DIP SWITCHES IN THE

OFF POSITION

VERSION 1

Summary of content (2 pages)

PAGE 1
CW-SYS WIRELESS DRIVEWAY SYSTEM INSTALLATION INSTRUCTIONS* VERSION 1 1. WHAT’S IN THE BOX 1. SENSOR “PUCK” 2. INTEGRATOR 3. AUGER SCREWS (2) 4. CR123A BATTERIES WITH CLIPS (2) 5. 3’ (1 m.) COAXIAL CABLE 6. TERMINAL BLOCK SCREWDRIVER OPTIONAL • 12VDC power supply (Part #CW-PS) 5. TEST MODE FOR SENSOR PUCK 1 2 4 6 3 5 There is a barcode serial number on the back of Integrator, bottom of puck, and on product box. When calling to talk about your product, please have one of these numbers handy.
PAGE 2
9. INTEGRATOR DIP SWITCHES Dip switches control sounder and repeater mode on Integrator. SOUNDER Turn dip switch 1 ON to turn sounder on. Sounder will beep 3 times when vehicle is detected. It will also “chirp” when sensor puck batteries are low and need replacing. REPEATER MODE Turn dip switch 2 ON to turn Integrator into a repeater. In repeater mode, the unit will continually receive and repeat any signal from the sensor to the Integrator installed in the home (see #11 below).