User's Manual

ManualsBrandsCARRIN ELECTRONICS ManualsElectronicsTHERMO SENSOR

KW9075RFWWVB

1.Features:

 RadiocontrolledclockwithWWVBsignal.

 915MHzRFreceivingfrequency.

 PerpetualCalendarUptoYear2069.

 12/24Hourtimedisplayselectable.

 CalendarDisplay.

 Dailyalarmwithadvancegraduallyalerting



2.MainUnitAppearance:



PARTA: 

A1:RadioControlledTime.

A2:RadioControlledIcon

A3:AlarmIcon

A4:Second

A5:IndoorTemperature

A6:Date&DayofWeek

A7:OutdoorTempe rature



PARTB:

B1:“SNOOZE”Button

B2:“+/12/24”Button

B3:“MODE/SET”Button

B4:“‐/C/F“Button

B5:“RESET”Button

B6:

“ALON/OFF”Button

B7:“ALERT”Button

B8:“SEARCH”Button

Summary of content (7 pages)

PAGE 1
KW9075RF WWVB 1. Features:  Radio controlled clock with WWVB signal.  915MHz RF receiving frequency.  Perpetual Calendar Up to Year 2069.  12/24Hour time display selectable.  Calendar Display.  Daily alarm with advance gradually alerting 2. Main Unit Appearance: PART A: A1: Radio Controlled Time.
PAGE 2
PART C C1: Wall Mount Hole C2: Battery Compartment Cover C3: Stand 3. Outdoor Sensor Appearance. D1: Outdoor Temperature D2: Transmission Indication LED D3: Battery Compartment D4: °C/°F” button D5: Wall Mount Hole 4. Getting Started: 4.
PAGE 3
5. Installation 5.1 Main Unit The main unit can be placed onto any flat surface (C3), or wall mounted by the hanging hole (C1) at the back of the unit. 5.2 Outdoor Thermo sensor The remote sensor should be securely mounted onto a horizontal surface. Note: Transmissions between receiver and transmitter can reach up to 100m in open area. Open Area: there are no interfering obstacles such as buildings, trees, vehicles, high voltage lines, etc. 6.
PAGE 4
repeats again at 3.00 a.m. 4.00a.m. and 5.00a.m.  The clock can be set to scan the time signal manually by holding “ ” button (B4) for 3 seconds. Each reception takes around several minutes. If receptions fail, scanning stops. (“ ” on LCD disappear) and repeats again on next full hour. E.g. scanning failed at 8:20a.m. It will scan again at 9:00a.m.  Stop scanning by holding “ ” button (B4) for 3 seconds. 7.
PAGE 5
Press “SNOOZE” (B1) button when alarm alerts. The alarm snoozes for 5 minutes,  then it alerts again. “ ” flashes on the LCD during the snooze time. This process can be repeated 7 times. Except “SNOOZE” button (B1), press any button to stop snooze alarm.  7.5  12/24 Hour Display mode: Press “12/24” (B2) button to select 12 or 24 hours mode. 8. Thermometer 8.1 Temperature display  Press “°C/°F” (B4) button to select Temperature in Celsius mode/ Fahrenheit mode.
PAGE 6
 The clock loses its time information when the battery is removed.  Avoid placing the clock near interference sources/metal frames such as computer or TV sets.  Do not expose it to direct sunlight, heavy heat, cold, high humidity or wet areas  The outdoor sensor must not be set up and installed under water. Set it up in away direct sunlight and Rain  Never clean the device using abrasive or corrosive materials or products.
PAGE 7
FCC Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.