CSD120/CSD130
Congratulations! Thank you for purchasing this digital drum set. The drum set has been Developed to act and play like a drum set but with greater ease. Before you use the instrument, we recommend you to read through this manual. Taking care of Your Digital Drum Set Location Handling and Transport - Do not expose the unit to the following Conditions to avoid deformation, discoloration or more serious damage. - Direct sunlight. - High temperature (near a heat)source, Or in car during the day time).
Contents 1. Assembly...........................................1 Assemble the drum stand.................1 Assemble the pads...........................3 Assemble the cymbals......................4 Assemble the module.......................5 Assemble the bass drum..................5 Assemble the pedal and bass drum.6 Connect the pads..............................6 2. Fold the drum stand..........................8 Arrange the pad cables.....................8 Fold the crash...................................
1. Assembly Caution： -While adjusting the collar, please take extra care to avoid injury. -Set the each part to the correct position. Assembly steps: Drum stand assembly 1). Take out the drum stand and loosen the screws of the collars. 2). Set the three master tube at 120°angle. 3). Screw down at the collars. Loosen the screws Screw down 4). Loosen the screws at the collars. 5). Set the L/R cymbal tubes to the proper height. 6). Screw down to fix the cymbal tubes.
Loosen the screws 10). Loosen the screws at the collars. 11). Adjust the HI-HAT collars to proper height. 12). Screw down to fix the HI-HAT tubes. Loosen the screws 13). Loosen the butterfly nuts. 14). Adjust the cymbal rod to proper height and angle. 15). Tighten the butterfly nuts. Loosen the butterfly nuts 16). Loosen the screws at the collars. 17). Adjust the U stand of snare to proper position. 18). Screw down.
Loosen the screws U stand 19). Loosen the screws at the collars. 20). Set the module stand to proper position. 21). Screw down. Loosen the screws module stand 22). Adjust the balance of the drum stand. 23). Tighten all the screws at the collars. Tighten the clip screw. Assemble the pads 1). Take out the pads（3 TOM and 1 Snare）. Loosen the square screw. 2). Assemble the pads onto the tubes and adjust the position. 3). Tighten the square screw.
Loosen the square screw Pad tube Assemble the cymbals 1）Loosen the butterfly nut on the left side of the HI-HAT. 2）Assemble the HI-HAT cymbal. 3）Tighten the butterfly nut（Note: don't overtighten） Loosen the butterfly nut 4). Loosen the butterfly nut on the cymbal rod. 5). Assemble the CRASH/RIDE cymbal onto the rod. 6).
Loosen the butterfly nut Assemble the module 1). Loosen the square screws of the module. 2). Assemble the module onto the module stand. 3). Screw down. Loosen the square screws Assemble the bass drum（only CSD130） 1). take out the bass drum and bass drum stand 2). loosen the square screw of the bass drum 3). assemble the bass drum on the stand 4). Tighten the square screw. Bass drum Square screw L=28 5). Fix the support bar to the pedal. 6).
7). Loosen the square screw of the hammer 8). tighter the square screw to fix the hammer loosen square screw Fix the hammer bar tighten the screw tighten the square screw the hammer pointing to the pad center Assemble the pedal and the bass drum 1)．Put the pedal to the left floor. 2)．Put the bass drum（with hammer）to the right floor. Note：CSD120 pedal is used as bass drum. Each of the pedal can be used as bass drum. CSD120 CSD130 Connect the pads 1).
RIDE CRASH TOM2 TOM1 TOM3 HI-HAT CYMBAL MODULE SNARE CABLE TIE (12 TOTALLY) BASS HI-HAT CTRL
2. Fold the drum stand Arrange the pad cables 1). Turn off the power supply. 2). Disconnect all the cables with the module. 3). Disconnect all the cables with the pads. 4). Take out the cable ties. 5). Rearrange the cables and bind them onto the tubes. 6). Disassemble the module and assemble the screws into the module and put the module into the bag. 7). Put the pedal into the bag. Note: The model CSD130 needs to be disassembled the hammer and the bass drum stand and put them into the bag.
1 2 3 Square screw 4). Loosen the square screw on the back of TOM1. 5). Put the pad vertically and adjust the position according to the dimension in the figure. Square screw 2-4cm 6). Loosen the square screw. Adjust Hi-Hat-CYMBAL & TOM1. 7). Put the collar up as the figure below. 8). Tighten the square screw.
Fold the RIDE 1) Loosen the butterfly knob and nut. 2) Loosen the square screw. a. Fold the RIDE cymbal as the figure below. b. Tighten the square screw. Tighten the butterfly nut & knob properly. Butterfly knob Square screw Butterfly nut Fold TOM2 and TOM3 1). Loosen the screws on the back of TOM2 and TOM3. 2). Put the pad vertically and adjust the pad position according to the dimension in the figure. 3). Loosen the square screw on the collar and adjust TOM2 & TOM3. 4).
6-8cm 1-2cm Fold the whole set 1). Loosen the square screw. 2). Rotate as the figure below and keep it stable while folding. 3). Rotate as the figure below and put the left and right part close. Direction 2 4). Rotate the supporting tube as the figure below.
Rotate 5). Fold the supporting part and keep the collar up closely. Collar Collar 6). Rotate as the figure below and fold the whole set. Note: User can put the whole drum set into bag (Optional bag).
2. Module function Front panel 3 5 15 8 6 9 2 12 1 14 7 11 13 10 4 1 -MASTER VOLUME+ Adjusts the volume of earphone and line output. 2 LED Display Displays the menu parameters. 3 -TEMPO+ Enter into the tempo setting (holding the button to change value quickly). 4 -DATA+ Adjusts the parameters,e.g. drum kit, Voice, etc (holding the button to change value quickly) 5 KIT REV ON/OFF Drum kit selection and reverb effect on/off. 6 SONG Selects DEMO SONG quickly.
Rear panel 16 17 18 19 20 21 22 16 USB interface Connects with PC to deliver MIDI signal. MIDI in/out port 17 Connects with external MIDI devices (The drum MIDI signal outputs via MIDI OUT to external audio source. The external MIDI signal inputs to the drum via MIDI IN.) 18 Trigger in connector Pad signal input connector. 19 AUX IN External stereo input connector, e.g. MP3 or CD player.
LED Display Drum kit LED lights up: the number means the drum kit number Tone LED lights up: the number means the voice number. the preset song LED lights up: the number means the preset song number. 4. Connect with external devices Connecting with audio system or drum speaker cabinet Connect one end with L/mono R, and the other end with audio system or drum amplifier. such as EDA series. Note: 1). L/mono is only for the left channel output. 2).
Connect with Headphones Connect the phone with 1/4" stereo connector on the module (if 1/8" phone is used, use an adaptor). The volume is controlled by the volume knob on the module. Connect with MP3 or CD player Connect the output of MP3 or CD player with AUX IN connector of the module. The input signal .can be mixed with the drum signal. User can strike the pad according to the metronome click of input signal.
Connectwith withPC PC Connect 1). Connect PC via USB Receives and delivers MIDI signal. 2). Connect PC via MIDI port MIDI IN: receives external MIDI signal. MIDI OUT: delivers pad signal to external MIDI device or PC. Connect with MIDI keyboard MIDI port: connect with the MIDI OUT connector of MIDI keyboard or external pads as the external audio source to control this digital drum. Power supply 1). Turn off the module power switch. 2). Connect the power supply with DC IN connector. 3).
turn off the power switch before connecting with other devices. 5. Operation Power switch 1). Confirm all the cables are connected well, then set the module volume to minimum, then turn on the power switch. POWER - MASTER VOLUME+ 2). When the display lights up, enter into the module menu operation (enter into the drum kit menu when on. Adjust the master volume Strike the pads and adjust the volume knob for proper master volume.
Select drum kit and reverb 1). Press [KIT REV ON/OFF] key to enter into drum kit setting or to switch drum kit and reverb effect. KIT REV 2). Press [KIT REV ON/OFF] key to enter into drum selection. The display shows drum kit number and the KIT LED lights up. Use [-DATA+] button to select drum kit. Preset drum kit: KIT01---20 User drum kit: USER01---10 DATA 3). Press [KIT REV ON/OFF] button to enter into reverb setting. LED shows the reverb effect.
VOICE 2). Strike the pad of which voice to be changed. Use [-DATA+] button to select the voice (voice Number:001-250，non-recycle) Adjust pad volume 1). When adjusting the pad volume, press once again [VOICE VOL/PAN/TUN] button to enter Into pad volume setting. The first LED shows “L”, and the other two LED shows the volume Value. VOICE LED lights up. 2). Strike the pad of which volume to be changed. Use [-DATA+] button to select the volume （00-32，non-recycle）. VOICE Pad pan 1).
1). In the drum kit menu, press [SAVE] button to enter into user drum kit setting. Use [-DATA+] button to select the user drum kit（U01-U10，non-cycle）. During this process, the drum kit number flashes. 2). Press the pad parameter setting to change the pad tone/volume/pan/tune. 3). Press [SAVE] button once again to save the drum kit setting, and the former drum kits will be covered by the new drum kit. The drum kit number stops flashing.
VOLUME Drum sound voume of the song 1). Press [ACCOMP VOLUME] button continuously to enter into the drum sound setting. The display shows letter “d”first, and the drum sound volume next. SONG LED lights up. 2). Use [-DATA+] button to adjust the drum sound volume of the song（0-32，non-recycle）. VOLUME Song tempo During playing DEMO SONG，use [-TEMPO+] button to adjust the song tempo. Drum sound of the song (percussion) Press [DRUM OFF] button to start/close the drum sound function.
3)Use the master volume knob to change the metronome volume. CLICK Note: during playing the songs, the metronome is closed. Press [CLICK] button to start metronome function. 6. Record and replay Record quickly 1). Press [RECORD] button, and [RECORD] LED lights up and flashes. It shows “REC”. 2). Strike the pads to start recording or record only the drum sound of the song being played. 3). Press [RECORD] button to stop recording. [RECORD] LED lights off. The song or the user's performance has been recorded.
3). Use [-DATA+] button to adjust the trigger sensitivity（01-08,non-recycle）. The higher the value means higher sensitivity. UTILITY Crosstalk rejection Strike a pad (trigger) and the vibration may cause crosstalk. 1). Press [SET UP] button continuously to enter into trigger sensitivity setting. The display shows letter “O” first and the crosstalk rejection level next. 2). Use [-DATA+] button to adjust the trigger sensitivity rejection level（01-16,non-recycle）.
CURVE4 CURVE5 CURVE6 Save the set-up Press [SAVE] button to save the 3 setting mentioned above: sensitivity/crosstalk rejection/striking force. Local control 1). Press [SET UP] button to enter into the local setting. It shows the local control status: “Lon”for ON or “Lof” for OFF. Use [-DATA+] button to switch. Refer to the following figure for the local control setting: MIDI signal Sound module Local control: used to control the connection of trigger detection and the audio source sequencer.
8. Reset setting Hold [TEMPO+] and [SET UP] button at the same time. It reset back to the factory setting: All user drum kits: voice/volume/pan/tuning Practical setting: sensitivity/crosstalk rejection/striking force curve 9. MIDI setting This equipment is compatible with various MIDI devices and can be used as trigger device or audio source. It is also compatible with part of GM standard, and can be used with many audio sequencer softwares together.
MIDI LIST FUNCTION Basic Default Channel Changed Default Mode Massages Altered Note Number: True Voice Velocity Note On Note Off after Key's Touch Ch's Pitch Bend Control 0 Change 1 5 6 7 10 11 64 65 66 67 80 81 91 93 120 121 123 Program Change :True Number System Exclusive System :Song Position Common :Song Select :Tune System :Clock Real :Comands Time Aux :Local On/Off :All Notes Off Massage :Active Sensing :Reset MIDI IMPLEMENTATION CHART TRANSMITTED RECOGNIZED 10 Ch 1~16 x x x x x x x x ********** 0~12
10. Trouble shooting Problem Reason No sound Please confirm the volume knob is not turned off Pad has no sound 1.confirm the pad connection is correct. 2.confirm the pad volume is not set to 0 Metronome has no sound Confirm the metronome volume is not set to 0 DEMO SONG has no sound Confirm the DEMO SONG volume is not set to 0 11.
12. DRUM KIT LIST NO. PRESET DRUM KIT NO.
13.VOICE LIST KICK ACOUSTIC SNARE NO.
41 42 43 44 45 46 47 48 SRSTD SRIMC4 POPSN1 POPSN2 POPSN3 POPSN4 POPSN5 POPSN5 ELECTRIC SNARE 49 50 51 52 53 54 55 56 57 SYNSN01 ESN11 ESN1 ESN2 ESN3 ESN4 ESN5 ESN6 ESN7 HI-HAT 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 CHH1 CHH2 CHH3 CHH4 CHH5 CHH6 CHH7 CHH8 LOOSHH1 LOOSHH2 LOOSHH3 LOOSHH4 OHHSTD OHIHAT1 OHIHAT2 OHIHAT3 OHIHAT4 OHIHAT5 PHHJZ PHH2 PHH3 CHHPOP1 CHHPOP2 CHHPOP3 CHHPOP4 31
EHH 83 84 85 86 87 88 89 EHH01 EHH02 EHH03 EHH04 EHH05 EHH06 EHH07 TOM 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 BRSHT1 BRSHT2 BRSHT3 TOM1 TOM2 TOM3 TOM4 TOM5 TOM6 TOM7 TOM8 TOM9 TOMHSTD TOMMSTD TOMPOP1 TOMPOP2 TOMPOP3 TOMPOP4 TOMPOP5 TOMPOP6 808T1 808T2 808T3 ETOM05 CYMBAL 114 115 116 117 118 119 120 121 122 123 124 CRASH1 CRASH9 CRSHJS1 CRSHJS2 CRSHSTD1 CRSHSTD2 LTCRSH1 LTCRSH2 LTCRSH3 ORCCYM1 ORCCYM2 32
PERCUSSION 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 ORCCYM3 ORCCYM4 RBLLSTD RIDEBELL REVCYM1 REVCYM2 REVCYM3 REVCYM4 RIDEJZ1 RIDEJZ2 RIDESTD RIDE1 RIDE2 REVCYMBAL SPLSH1 SPLSH2 CRASHC1 CNCYMBAL CRASHPOP1 CRASHPOP2 CRASHPOP3 CRASHPOP4 SPLASHC RIDELC2 RIDEH1 RIDEH2 ECRASH1 ECRASH2 ECRASH3 ECRASH4 SPLASH 156 157 158 159 160 161 162 163 164 165 166 167 EMRCA1 EMTRI ETRNGL1 ETRNGL2 EBELL1 ECBSA2 ETMBRIN1 ETMBRIN2 CABASA1 CABAS
CHKR03 CLAP1 CLAP2 CLAP3 CLAP4 COWBLL1 COWBLL2 COWBLL13 COWBLL14 COWBLL15 HAGOGO1 HAGOGO2 HAGOGO3 HIBNGO01 HIBNGO02 HTMBL1 HTMBL2 HTMBL3 LOBNGO LOCNGA01 LOCNGA02 MHCNGA03 MTRNGL OHCNGA01 OHCNGA02 OHCNGA03 OHCNGA04 OPNTRNGL TMBRN1 TMBRN2 TMBRN3 TMBRN4 TMBRN5 VSLP03 CNBGONG CNLCYMBL CNLDRM1 CNLDRM2 CNSCYMBL CNSDRM CNSGONG SUPRGNG TAIKO1 TAIKO2 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209
TAIKO3 TAIKO4 TAIKOSD1 TAIKOSD3 CHIM1 CHIM2 STICK2 TIM1 TIM2 TIM3 TIM4 TIM5 TMPNS3 BELLTREE High Q SLAP SCRATCH PUSH SCRATCH PULL STICKS CLIP METRONOME CLICK METRONOME BELL SHAKER JINGLEBELL CASTANETS MUTESURDO OPNSURDO L0TMBL1 LAGOGO1 MRCAS1 SWHSL1 LWHSL1 SGUIRO LGUIRO CLV HWBLK LWBLK MCUICA OCUICA 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 35
14.GM PERCUSSION LIST Note No. 27－D#1 28 E1 29－F1 30－F#1 31－G1 32－G#1 33－A1 34－A#1 35－B1 36－C2 37－C#2 38－D2 39－D#2 40－E2 41－F2 42－F#2 43－G2 44－G#2 45－A2 46－A#2 47－B2 48－C3 49－C#3 50－D3 51－D#3 52－E3 53－F3 54－F#3 55－G3 56－G#3 57－A3 58－A#3 59－B3 60－C4 61－C#4 62－D4 63－D#4 64－E4 GM Percussion Voice No.
65－F4 66－F#4 67－G4 68－G#4 69－A4 70－A#4 71－B4 72－C5 73－C#5 74－D5 75－D#5 76－E5 77－F5 78－F#5 79－G5 80－G#5 81－A5 82－A#5 83－B5 84－C6 85－C#6 86－D6 87－D#6 183 239 178 240 164 241 242 243 244 245 246 247 248 249 250 190 195 234 235 225 236 237 238 High Timbale Low Timbale High Agogo Low Agogo Cabasa Maracas Short Whistle Long Whistle Short Guiro Long Guiro Claves Hi Wood Block Low Wood Block Mute Cuica Open Cuica Mute Triangle Open Triangle Shaker Jingle Bell Bell Tree Castanets Mute Surdo Open Surdo 37 HTMBL1
15.DEMO SONG LIST NO.
Carlsbro Holdings Ltd Unit 11, Torc MK, Chippenham Drive, Milton Keynes, MK10 0BZ .United Kingdom Tel-+44(0)1908 281072 Web: www.carlsbro.com Email: sales@carlsbro.
