User Manual

ManualsBrandsCarestream Health ManualsElectronicsWiFi Control Box

Table Of Contents

KODAK RVG 6500 System and KODAK RVG 6500

IPS System

User & Installation Guide

Summary of content (72 pages)

PAGE 1
KODAK RVG 6500 System and KODAK RVG 6500 IPS System User & Installation Guide
PAGE 2
Notice The User & Installation Guide for the KODAK RVG 6500 System includes information on the installation of the device as well as its usage. We recommend that you thoroughly familiarize yourself with this Guide in order to make the most effective use of your system. The KODAK RVG 6500 System, wireless digital intra-oral X-ray system, is intended to produce an image of the dental area at the direction of dentists, oral surgeons and orthodontists for x-ray imaging of the dento-maxillo-facial area.
PAGE 3
Contents Chapter 1 Conventions in this Guide . . . . . . . . . . . . . . . . . . . 1 Conventions in This Guide Chapter 2 KODAK RVG 6500 Systems Description. . . . . . . . . . . 3 KODAK RVG 6500 Packaging of KODAK RVG 6500 System . . . . . . . . . . 3 Systems Packaging Packaging of KODAK RVG 6500 IPS System . . . . . . . . 3 Opening the Boxes . . . . . . . . . . . . . . . . . . . . . . 3 Chapter 3 KODAK RVG 6500 Systems Overview . . . . . . . . . . . .
PAGE 4
Launching the X-Ray . . . . . . . . . . . . . . . . . . . 37 Chapter 7 The RVG Mobile Application Overview . . . . . . . . . . . . 39 RVG Mobile Downloading the RVG Mobile Application . . . . . . . . . . 42 Application If iPhone/iPod Touch is Connected to the Internet . . . 42 If iPhone/iPod Touch is not Connected to the Internet . 43 Connecting The Device to the WiFi Access Point . . . . . . 44 Configuring the Preference Settings . . . . . . . . . . . . .
PAGE 5
1 Conventions in This Guide Conventions in this Guide The following special messages emphasize information or indicate potential risk to personnel or equipment: WARNING: Warns you to avoid injury to yourself or others by following the safety instructions precisely. CAUTION: Alerts you to a condition that might cause serious damage. Important: Alerts you to a condition that might cause problems. Note: Emphasizes important information. Tip: Provides extra information and hints.
PAGE 6
2 Chapter 1 Conventions in This Guide
PAGE 7
2 KODAK RVG 6500 Systems Packaging KODAK RVG 6500 Systems Description The KODAK RVG 6500 Systems is available in 2 configurations: • The KODAK RVG 6500 System OR • The KODAK RVG 6500 Intelligent Positioning System (IPS) System The KODAK RVG 6500 Systems information applies to both KODAK RVG 6500 System as well as the KODAK RVG 6500 IPS System. The KODAK RVG 6500 IPS System information applies only to information relevant to the IPS system.
PAGE 8
4 Chapter 2 KODAK RVG 6500 Systems Packaging
PAGE 9
3 KODAK RVG 6500 Systems Overview KODAK RVG 6500 Systems Overview • The KODAK RVG 6500 System OR • The KODAK RVG 6500 Intelligent Positioning System (IPS) System Figure 1 KODAK RVG 6500 System Components 2 1 1 The sensor and the control box 2 The WiFi access point 3 The medical power supply for the RVG system 3 The KODAK RVG 6500 IPS System is composed of all the KODAK RVG 6500 system components and the IPS aiming ring.
PAGE 10
RVG Functional Components Overview Figure 3 RVG Functional Components Overview 1 2 A 4 5 3 B 1 Battery status indicator LED: Not charged Charging (blinking) Charged with charger connection OFF 2 Charged without charger connection Sensor remote control button and the ON/OFF button: OFF mode: Press 5 seconds to turn OFF 〈 〈 〈 〈 Connecting to WiFi AP (blinking): Press 2 seconds to turn ON.
PAGE 11
WiFi Access Point Functional Components Overview The WiFi access point is the wireless equivalent of the wired internal Local Area Network (LAN). The WiFi access point provides connectivity between the computer and the RVG sensor(s) enabling you to use the KODAK RVG 6500 within your practice area. See the manufacturer guide for any detailed information on the WiFi access point. Figure 4 WiFi AP Back Panel Overview 3 2 1 1 Power adapter outlet.
PAGE 12
8 Chapter 3 KODAK RVG 6500 Systems Overview
PAGE 13
4 Imaging Software Overview Computer System Requirements This section specifies the minimum computer system requirements for KODAK RVG 6500 intraoral imaging system software. If necessary you must update your computer system configuration. The computer and its screen should ideally be situated in or close to the operating area, in the visual field of the practitioner when he is with the patient. The visual access of the acquired image for the patient encourages communication.
PAGE 14
Table 1 Minimum Computer System Requirements (Continued) Item Viewing and Acquisition • Operating system • • Ethernet interface Comments Windows XP Home / Pro edition SP3 Windows Vista 32 bits Windows Vista SP1 1 Ethernet interface USB 2.0 2 ports Wireless adapter Wireless 802.11g Adapter (USB, PCMCIA or PCI) CD/DVD drive DVD-ROM drive is required to install the product. Backup media Removable/portable, external hard disk drive.
PAGE 15
The RVG Acquisition Interface The RVG Acquisition interface module is a user-friendly working interface that was designed and developed specifically for the KODAK RVG 6500 intraoral imaging system. Figure 6 RVG Acquisition Main Interface 1 2 Sensor orientation: Pre-orients how the x-ray image is displayed in the Imaging Window. Preview screen: Indicates the 90 second activation time for acquisition. • Displays the acquired x-ray image instantly after acquisition.
PAGE 16
Figure 7 List of Available Sensors The sensor name and battery status: Battery status. The WiFi status: Wifi transmission is available. Wifi transmission is available but not good. WiFi transmission is not available. The Sensor availability: Sensor is connected to your computer and ready for use. Click Sensor is not connected to your computer. Click to disconnect. to connect. Refresh button refreshes the list of sensors visible in the computer.
PAGE 17
The IPS Aiming Ring Interface Overview The IPS aiming ring interface is a user-friendly working interfaces that was designed and developed specifically for the KODAK RVG 6500 IPS System intraoral imaging system. It enables you prior to acquisition to dynamically and visually center the x-ray beam to the RVG sensor using the centering indicator.
PAGE 18
IPS Aiming Ring Interface and RVG Sensor Centering The IPS aiming ring interface enables you to correctly position the X-ray generator to the RVG sensor. The IPS interface enables you to manage the X-ray centering and the proper paralleling technique achievement. Sensor Display • Sensor is not centered. • Centering indicators are red. Result • Sensor active surface not fully exposed to X-ray. • Image will have a cone cut. • Parallel technique not achieved. • Image distortion.
PAGE 19
The RVG Mobile Application Overview For the RVG Mobile Application overview, see the relevant Chapter.
PAGE 20
16 Chapter 4 Imaging Software Overview
PAGE 21
5 Setting Up the KODAK RVG 6500 Systems Important: Your computer must have an Ethernet board and be WiFi equipped before installing the KODAK RVG 6500 systems. WiFi Access Point Setup Configurations There are 2 WiFi access point setup configuration options: • • The wired WiFi access point setup configuration The wireless WiFi access point setup configuration You need to decide your setup configuration before starting the WiFi setup.
PAGE 22
WiFi AP Wireless Configuring Setup You can chose to have a wireless WiFi access point configuration. In this configuration setup, the computer is connected to the WiFi access point through a router, that is, through a dongle or a PCI card. In this configuration, several sensors can be connected to the same access point and shared between several computers and chairs.
PAGE 23
Installing the KODAK Dental Imaging Software Before installing the KODAK Dental Imaging Software, check that: • • The computer has all the PC system requirements You have the software DVD as of version 6.12 or higher To install the KODAK Dental Imaging Software, follow these steps: 1 Insert the software DVD in the DVD-ROM drive of the computer. Wait for the installation program to start. If the program does not start automatically, click Start > Run and enter D:\setup.
PAGE 24
5 The License Agreement dialog box is displayed. Accept and click Yes. 6 The Choose Destination Location dialog box is displayed. Click Next if you accept the default destination folder (c:\program files\Kodak\Kodak Dental Imaging Software) or browse to choose another destination folder. 7 The KODAK Dental Imaging Software dialog box is displayed. The Patient file is selected by default but you must select the device.
PAGE 25
〈 Click on the drop-down list of No Intraoral Radiography Installation. 〈 Select RVG 5x00/6x00. 〈 Click Next to begin the installation. The InstallShield Wizard is displayed. Let the installation process run automatically.
PAGE 26
The Kodak Patient file - InstallShield Wizard is displayed while the patient files are installed on the hard drive. The Software Installation dialog box is displayed while the installation process continues. Click Continue Anyway until the dialog box disappears. 9 The Installation Complete dialog box is displayed when the installation is finished. Click Finish. The and are installed on your desktop.
PAGE 27
If your PC operating system is not compatible with the system requirements If your PC operating system is not compatible with the system requirements, the System incompatibility dialog box is displayed. Click Download, your application will close automatically. Follow the on-screen instructions to install the required “Windows Wireless component”. Reboot your PC when the installation is completed. Installing the Setup Installation Software 10 Click on your desktop.
PAGE 28
12 In the central pane, click RVG Wireless System Configuration, to access the “Setting Up the WiFi AP” window (see and follow step 10). 13 Before the setting up of the KODAK RVG 6500 System procedures, have with you the: SSID Password RVG8_NETWORK 7794AA6500EC239BFF4554DD80 14 The “Setting Up the WiFi AP” window is automatically displayed. Follow the on-screen instructions to set up the RVG system. Once you have finished setting up the RVG system, you must register the KDIS Licence.
PAGE 29
Registering the KDIS Licence To register the KDIS licence, follow these steps: 1 Double-click 2 Create a patient record. From the toolbar, click Click 3 to open the Patient Window. and enter the required patient information. to access the Imaging Window. The Enter the licence number dialog box is displayed. Enter the licence number and click Validate if you have the licence number or click Cancel to continue. The icon appears on the toolbar of the Imaging Window.
PAGE 30
Mounting the RVG Holders The RVG sensor and control box holders enable you to have them at reach to optimize your workflow. You need to install the RVG sensor and control box holders where it best suits your workflow, the X-ray generator arm, the chair, etc.... To mount the RVG sensor and control box holders, follow these steps: 1 Attach the RVG control box holder with the double-face adhesive or the Velco strap supplied on the side of the X-ray generator arm.
PAGE 31
Mounting the IPS Aiming Ring on the X-Ray Generator Before mounting the IPS aiming ring, make sure that: • You have the necessary tools: 15 mm • • You have cleaned the X-ray generator tube head with disposable cleaning wipes. You have asked the practitioner his preference for the position of the aiming ring on the X-ray tube head, with the ON/OFF button on the left or right side of the X-ray tube head.
PAGE 32
5 Select the appropriate aiming ring holding brackets (B): • • • 6 For a cone shape x-ray tube head (HY415). For a cylindrical shape x-ray tube head with diameters from 55.5 mm to 65 mm (HY414). For a cylindrical shape x-ray tube head with diameters from 64 mm to 77.5 mm (HY413) mounted on the ring. Measure from the opening of the x-ray tube head 30mm. Mark the 30mm with a pencil on both sides of the x-ray tube head.
PAGE 33
10 Place the cable tie (A) around the holding brackets (B), make a knot and place it in the cable tie holder (C). Pull to tighten and cut what exceeds the knot. Retighten the screws, if needed. A B x4 C C A 11 Position correctly the front cover with the board making sure that the ON/OFF button is on the appropriate place. A A 12 Position correctly the attachment brackets (A). 13 Press quickly the ON/OFF button to turn ON the IPS device and check that the front upper LED is lit.
PAGE 34
30 Chapter 5 Setting Up the KODAK RVG 6500 Systems
PAGE 35
6 Acquiring an Image Locking the RVG Sensor to the Computer You need to lock the RVG sensor to the computer where the acquired image must appear. Important: You can use the RVG sensor to acquire an image while charging ONLY with the medical charger. Locking a Single RVG Sensor to the Computer If you have a single RVG sensor, you need to lock it only once to the computer where the acquired image must appear.
PAGE 36
3 In the RVG Acquisition interface, click to access the RVG sensor list. 4 Find the RVG sensor in the sensor list. The sensor is identified with 5 Click to connect the sensor to your computer, becomes . . Locking Several Shared RVG Sensors to the Computer If you have several shared RVG sensors, you need to lock the selected RVG sensor to the computer where the acquired image must appear.
PAGE 37
7 In the RVG Acquisition interface, click refresh the sensor list. 8 Find the selected RVG sensor in the sensor list: If to access the RVG sensor list. If needed, click to do the following: Click to lock the sensor to your computer, If becomes . do the following: Click to unlock from the computer it is locked to and press quickly on the remote control button while the light is blink blue (A). If the unlocking was not executed you must redo the unlocking process.
PAGE 38
Acquiring an Image with the RVG Sensor To acquire an image with the RVG sensor, follow the instructions in the presented order. Preparing the RVG Sensor To prepare the selected RVG sensor, follow these steps: 1 Select an appropriate positioner for the region of interest and the sensor size. 2 Cover with a disposable hygienic sleeves specifically designed for each sensor size. . Important: To prevent cross-contamination, use a new hygienic barrier for each new patient.
PAGE 39
Preparing the X-Ray Generator To prepare the x-ray generator, follow these steps: 1 Press the remote control button of the selected RVG control box to access the RVG Acquisition interface. (Optional) Press on the remote control button several times to pre-orient the sensor orientation. The acquired image is displayed with the last selected orientation on the Imaging Window. (Optional) Click To select the tooth or teeth number. Click to return to the RVG Acquisition interface.
PAGE 40
3 Insert the sensor holding it horizontally in the patient’s mouth. Positioning in the patient’s mouth depends on the region of interest. 4 Approach the x-ray generator tube head to the patient. (Optional) If you are using the IPS aiming ring system, press the ON button. If you are in front of the aiming ring, make sure that the front LED is ON. If you are positioned in the back of the aiming ring, a quick press on the ON/OFF button will turn on the LED on the back.
PAGE 41
Launching the X-Ray To launch the x-ray, follow these steps: 1 Ask the patient to remain still. 2 Position yourself either 2 meters behind the x-ray generator or outside the door. 3 Keep visual contact with the patient during the x-ray. 4 Trigger the x-ray with the remote control of the x-ray generator. The image appears in the preview screen of the RVG Acquisition interface. The light on the remote control button blinks blue indicating the image transmission.
PAGE 42
38 Chapter 6 Acquiring an Image
PAGE 43
7 RVG Mobile Application The RVG Mobile Application Overview Important: iPhone®/iPod® touch devices are not included or delivered with the KODAK RVG 6500 Systems. The RVG mobile interface is a user-friendly working interface that is designed and developed specifically for the KODAK RVG 6500 intraoral imaging system. The RVG mobile interface module, to be used on your Apple iPhone®/iPod® touch, is downloadable from the Apple Store.
PAGE 44
Touch the different fields to access the different options.
PAGE 45
Figure 13 X-Ray Acquired Image Window 1 Gallery button: Accesses the slides of the acquired images. 2 Preview screen: Displays real-time the acquired image. 3 Back button: Returns to the previous image. 4 5 6 Image contrast button: Enhances the different zone of interest: • 0: Perio: Optimizes the display of periodontal tissues. • +: Endo: Optimizes the contrast values over the entire range.
PAGE 46
Downloading the RVG Mobile Application If iPhone/iPod Touch is Connected to the Internet If your iPhone®/iPod® touch device is connected to the Internet, follow these steps: 1 On the main window, tap . A window is displayed with different applications. 2 Tap . In the search field, enter RVG mobile and tap displayed. 3 Tap 4 Tap 5 Tap . The RVG Mobile Icon is . The RVG mobile detail window is displayed. . The is displayed. to start the download and follow the on-screen instructions.
PAGE 47
If iPhone/iPod Touch is not Connected to the Internet If your iPhone®/iPod® touch device is not connected to the Internet the Application Store window is displayed when you want to access the Apple Store to download. In this case, follow these steps: 1 Connect your iPhone®/iPod® touch device to the computer. 2 Go to the Apple Store web site 3 Click computer, . . Follow the on-screen instructions. When the iTunes is installed on your appears on your desktop. 4 Double-click displayed. .
PAGE 48
9 Check Sysnc Applications and the check box of the RVG Mobile Application. Click to send the RVG Mobile Application to your device. 10 Click when the upload process ends. You must now connect your device to the WiFi access point. Connecting The Device to the WiFi Access Point To connect your device to the WiFi access point, follow these steps: 1 On your device, tap 2 Tap the Settings window is displayed. . Tap OFF to change to ON. The WiFi Networks window is displayed.
PAGE 49
3 Tap RVG8_Network. The Enter Password window is displayed. 4 Enter the Password: 7794AA6500EC239BFF4554DD80. Tap 5 When the WiFi connection is established, signal is displayed on the WiFi Networks window and a check appears next to RVG8_Network. 6 Tap to return to the Settings window. You must now configure the preference settings of the RVG Mobile Application.
PAGE 50
3 In the Mode window, tap X-Ray field, a check sign appears in the X-Ray field. 4 Tap 5 In the RVG Mobile window, tap Image Processing field.The Processing window is displayed. 6 In the Processing window, Endo (optimizes the contrast values over the entire range) is selected by default. We recommend that you keep this selection. You can select any type of image contrast while reviewing the acquired image using the image contrast functions of your device (see Figure 14).
PAGE 51
9 Tap the relevant convention. A check sign appears in the field that you have selected. 10 Tap to return to the RVG Mobile window. The Settings window is displayed with the new selections. These selection are automatically saved. 11 If the settings are correct, tap the Home button to return to the main window. The configuration of the settings is saved and finished.
PAGE 52
Locking the RVG Sensor to the Apple Device To lock the RVG sensor on your Apple device, you need to have the RVG mobile application on your iPhone®/iPod® touch device. To ensure best use, follow the instructions in the following order. Important: Make sure that you have connected your device to the WiFi access point before starting. Accessing the Sensor List Window You must access the Sensor list window before locking the RVG sensor to your Apple device.
PAGE 53
2 Tap . Tap to validate. Locking Several Shared RVG Sensors to the Apple Device If you have several shared RVG sensors, you need to lock the selected RVG sensor to the device where the acquired image must appear. To lock the selected RVG sensor to your device, follow these steps: 1 In the Sensor list window identify the selected sensor. If : Sensor is locked on your device and ready for acquisition. You can continue to section “Finding or Creating a Patient File”.
PAGE 54
If 2 : Sensor is available you must lock it on your device. In the Sensor list window, tap the selected sensor. Then, tap . Tap . to validate. If : Sensor is not available (locked on another device). You must unlock and then lock the sensor on your device. In the Sensor list window, tap the selected sensor. Then, tap . Tap to validate. Press quickly on the remote control button while the light is blink blue (A). If the unlocking was not executed you must redo the unlocking process.
PAGE 55
Then, tap . Tap to validate.. Finding or Creating a Patient File To find or create a patient file, follow these steps: 1 Tap to access the Patient window. 2 In the Patient window, in the search field enter the patient’s name and tap to open the patient’s file or search by alphabetical order. If you need to create or edit a patient’s information, tap to access the Edit Patient window. Tap the different fields to access the different options. Edit or modify the patient’s information.
PAGE 56
3 Tap on the selected name, the displayed window presents the patient information and the sensor status. Acquiring an Image with the RVG Mobile Application Preparing the RVG Sensor To prepare the selected RVG sensor, follow these steps: 1 Select an appropriate positioner for the region of interest and the sensor size. 2 Cover with a disposable hygienic sleeves specifically designed for each sensor size. . Important: To prevent cross-contamination, use a new hygienic barrier for each new patient.
PAGE 57
Preparing the X-Ray Generator To prepare the x-ray generator, follow these steps: 1 Select the x-ray timing according to the region of interest and the patient type (follow the user instructions of your x-ray generator). 2 Insert the sensor holding it horizontally in the patient’s mouth. Positioning in the patient’s mouth depends on the region of interest. 3 Approach the x-ray generator tube head to the patient’s chair. (Optional) If you are using the IPS aiming ring system, press the ON button.
PAGE 58
5 Correctly align the tube head with the sensor. 6 Make sure that the tube head is not shacking. Launching the X-Ray To launch the x-ray, follow these steps: 1 Ask the patient to remain still. 2 Position yourself either 2 meters behind the x-ray generator or outside the door. 3 Keep visual contact with the patient during the x-ray. 4 Touch solid green. to acquire an image.The 90 seconds timer is displayed.
PAGE 59
5 Trigger the x-ray with the remote control of the x-ray generator. The image appears in the preview screen of your device. The light on the remote control button blinks blue indicating the image transmission 6 When the acquisition ends, the light on the remote control button becomes solid green. At this stage, while the count down continues, you can continue acquiring other images. If the count down ends and you wish to acquire other images then redo step 5. 7 Check the image quality.
PAGE 60
10 Touch to access the summary of the last acquired image. You can enter any comments in the yellow comment’s field. 11 Tap to access the dental arch window. Tap and touch the selected tooth or teeth number. 12 Tap to return to the previous window. 13 Tap to view all the acquired images of the patient. You can touch each acquired image in the gallery and do step 10 and 11.
PAGE 61
14 Tap to display the patient information. 15 Tap to access the Patient window. 16 When you want to transfer all the acquired images of the patients to your computer, in the Patient window, touch the transfer window is displayed. 17 Launch the KDIS, click , and follow the on-screen instructions.
PAGE 62
58 Chapter 7 RVG Mobile Application
PAGE 63
8 Troubleshooting Occasionally, malfunctions can occur during use in the event of an incorrect action. The quick trouble shooting and the Information “I”, will guide you through the actions you need to take to correct the malfunction. Important: If the malfunction persists or more serious conditions occur, contact your representative.
PAGE 64
Table 2 Quick Trouble Shooting (Continued) Malfunction When you turn ON your RVG sensor, it blinks blue then becomes solid blue but the sensor cannot be found in the sensor list on the computer. Possible Cause • • WiFi access point is not ON. Configuration problem. Action • • Check that the WiFi access point is ON.
PAGE 65
Information Messages An information “I” error code with a message is displayed on the popup on your computer screen. The following table lists the information messages and the action to take. Table 3 Information Messages Information Error Code I1 I2 I3 Information Message Action Communication problem with the wireless RVG sensor. Turn off then on your sensor or restart your computer. If the problem persists, contact your representative. 〈 Wireless sensor error.
PAGE 66
Table 3 Information Messages (Continued) Information Error Code Information Message I 12 Memory allocation problem. Restart your computer. If the problem persists, contact your representative. 〈 Error during the image transfer. Turn OFF then ON your wireless sensor and restart the acquisition software. If the problem persists, contact your representative. 1. Turn Off then ON the RVG sensor. I 13 I 14 System error. Close and restart the acquisition software.
PAGE 67
9 Maintenance This chapter describes the maintenance task that you need to perform regularly for your KODAK RVG 6500 system and the accessories. Daily The RVG Sensor The RVG sensor is supplied in a non-sterile state. Single-use disposable protective hygienic sleeves must cover the RVG sensor before placing it in the patient’s mouth. These sleeves are conform to the ISO EN 10993. To prevent cross-contamination, use a new hygienic barrier for each new patient and disinfect the RVG sensor.
PAGE 68
Cleaning the RVG Sensor Control Box The RVG sensor control box must be cleaned with disposable cleaning wipes similar to those used for the computer screens. . WARNING: Never immerse the RVG sensor control box in any solution. Cleaning the Positioning Accessories . WARNING: Do not use chemical autoclave for the toothbrush holders and avoid direct contact with the metallic part of the autoclave.
PAGE 69
Replacing the RVG Battery To replace the RVG battery, follow these steps: 1 Turn OFF the RVG sensor. 2 Make sure that the RVG sensor is not connected to the mains outlet. 1 Press down with fingers and slide the trap door (A) protecting the battery on the back of the control box. A A 2 Remove carefully the connector (B) to remove the used battery. 3 Insert the connector (B) of the appropriate battery. WARNING: Make sure that the battery is inserted correctly in its connector.
PAGE 70
RVG Control Box with IPS board B A Important: For the RVG with IPS board, make sure that you insert the battery gently avoiding any damage to the IPS board. 5 Plug one end of the medical charger in the USB port of the RVG control box. 6 Plug the other end to the mains outlet. The blinking green light of the battery status (A) on the control box indicates the charging process. The first charging takes about 4hours. When the green light becomes solid green (B) the charging is complete.
PAGE 71
Important: You can use the RVG sensor to acquire an image while charging ONLY with the medical charger. 7 You can use the USB cable to charge RVG battery with the computer. WARNING: NEVER use the RVG sensor to acquire an image while charging with the USB cable. Important: Remove the battery from the control box if you will not use it for a long period of time.
PAGE 72
Replacing the IPS Aiming Ring Battery Important: When the battery is low the LEDs light becomes orange. You need to replace the IPS battery. To replace the IPS aiming ring battery, follow these steps: 1 Remove the attachment brackets (A). 2 Remover the front cover. 3 Remove the used 4 batteries. x4 A A 4 Replace correctly the new 4 batteries respecting the polarities. 5 Replace the front cover. 6 Replace the attachment brackets (A).