™ Q2 MultiSet ™ communication in motion ™ Gebrauchsanleitung Guide d’Utilisation Guida di Avvio Guia de Usario User Guide
© Cardo Systems, Inc. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Cardo Systems, Inc. is under license. Other trademarks and trade names are those of their respective owners.
Congratulations and thank you for choosing the scala rider Q2 MultiSet Bluetooth® Headset package for bikers. This User Guide will help you operate the headset, but you should first familiarize yourself with the Bluetooth functionality of your cellular phone and/or GPS device before using the scala rider Q2. This retail box contains two scala rider Q2 headsets that already factory paired (see details below).
SET UP AND CONFIGURATION 2 Wall Chargers 2 Allen Wrenches 2 sets of Velcro Pads 2 MP3 Cables 2 MP3 Cable Holders Mobile phone 2 Glue Plates 2 Pre-moistened Towelettes 2 Carry-Pouches 4 Microphone Sponges Flat sponge for full-face helmets and round sponge for other helmet types User Guide, including Warranty and Registration form Built-in FM radio Driver-toPassenger Full-duplex Intercom Connection scala rider Q2 or other scala rider headset GPS MP3 player Bike-to-Bike Intercom up to 500 m / 540 yd )in
Your two MultiSet units are already factory paired and ready for use. If for any reason, you have to pair them again, proceed as follows: 1. If either headset is turned OFF, turn it ON by pressing and holding the CTRL Button until the Blue Light flashes three times. 2. Make sure that both headsets are now flashing slowly in Blue. 3.
1. Place the scala rider Q2 into Intercom Pairing mode following the instructions in the PRIMARY BUDDY PAIRING section above. 2. Once the Red Light begins flashing rapidly, press and hold Volume up for three seconds. 3. The Red and Blue Lights will flash five times, confirming that the Reset Pairing was successful.
GETTING STARTED ATTACHING THE CLAMP ON THE HELMET The Helmet Clamp must be attached to the left side of the helmet. Once attached, the headset unit can be mounted or released from the Helmet Clamp at any time. If you wish to connect your MP3 player to your headset, please refer first to the assembly instructions listed in section: USING THE MP3 PLAYER WITH YOUR HEADSET. There are two methods that can be used in order to attach the Clamp onto the helmet: Standard Method: Recommended for most helmet types.
sure to clean the selected area prior to the gluing process). 4. Use the pre-moistened Towelette to clean the helmet area where you want to install the Glue Plate. Allow to dry thoroughly. 5. Peel the foil cover from the Glue Plates’ adhesive pad. 6. Place the Glue Plate into position according to #3. Press firmly 15 seconds on all 3 parts of the Glue Plate. 7. The adhesive pad bonds to full strength over the next 24 hours. Therefore it is recommended to not use the headset during this 24 hour period. 8.
Press here to remove USING THE HEADSET GENERAL USAGE GENERAL FUNCTIONS DESIRED RESULT: Turn on the headset Turn off the headset Increase the volume Decrease the volume A high priority Audio Source will always interrupt any lower priority Audio Source. i.e.
Reconnecting the Intercom: If the scala rider Q2 and its Intercom Buddy headset go out of range and disconnect from each other, the scala rider Q2 will automatically try to reconnect to its Intercom Buddy for five minutes. You can manually reconnect at any time by pressing the MC Button (single tap for Primary Buddy and double tap for Secondary Buddy). Receiving Intercom calls If you are not speaking with any one, once the other party tries to initiate a Buddy Intercom call, the call will begin immediately.
STATUS LIGHT STATES received, or when you decide to initiate a call. When the conversation is over, the headset automatically tunes back in to the FM Radio. Turning the FM Radio On While no call is on the headset (either mobile phone call or Intercom call), press and hold the MC Button on your headset for three seconds to turn on the radio. The radio tunes in to the last radio station you were listening to. With some phones you should wait a few seconds after ending a call before turning on the Radio.
Saving an FM Radio Station The FM Radio is equipped with a memory capacity of six stations. • Select the station you wish to replace by tapping the MC button until you find the station you want to replace. • Search for a new station as described above. • Tap the MC Button within 20 seconds of finding the station to save the current station. If you don't save the station, the Radio will exit search mode without saving the current station. You can still continue to listen to the current unsaved station.
Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
following carefully before using the device. If you do not accept all terms of this agreement, you should immediately return the product for a full refund. By using the headset you agree to be bound to this agreement and forfeit the right to sue. confirm that you will not consume any alcohol that may affect your alertness or any mind-altering substance, and will not carry, use or consume these substances before or during the use of the Device.