User Guide MultiSet ™ Gebrauchsanleitung Guide d’Utilisation Guida di Avvio Guia de Usario
| SCALA RIDER® Q2™ MultiSet
SCALA RIDER® Q2™ MultiSet | CONTENTS OF RETAIL BOX Congratulations and thank you for choosing the SCALA RIDER Q2 MultiSet Bluetooth® Headset package for bikers. This User Guide will help you operate the headset, but you should first familiarize yourself with the Bluetooth functionality of your cellular phone and/or GPS device before using the SCALA RIDER Q2. This retail box contains two SCALA RIDER Q2 headsets that already factory paired (see details below).
| SCALA RIDER® Q2™ MultiSet SET UP AND CONFIGURATION 2 Wall Chargers Rider-toPassenger Full Duplex Intercom Connection 2 Allen Wrenches 2 sets of Velcro Pads 2 MP3 Cables Embedded FM Radio Bike-to-Bike Intercom up to 500 meters (1,640 ft.
SCALA RIDER® Q2™ MultiSet | STEP 2 (Optional) SET UP FOR RIDER-TO-PASSENGER INTERCOM: PAIRING 1. If either headset is turned OFF, turn it ON by pressing and holding the CTRL Button until the Blue Light flashes three times. There are two ways that the SCALA RIDER Q2 can be used for Riderto-Passenger communication. A. Both Rider and Passenger are using SCALA RIDER Q2 headsets (like the two units in your retail package).
| SCALA RIDER® Q2™ MultiSet 1. Place the SCALA RIDER Q2 into Intercom Pairing mode following the instructions in the PRIMARY BUDDY PAIRING section above. phone’s instructions. Please consult your phone’s User Manual for more information. 4. After a few seconds the phone will list the SCALA RIDER Q2 as a discovered device. Select it and follow your phone’s instructions to accept the pairing. 5. When prompted enter 0000 (four zeros) as your PIN or passkey. 6.
SCALA RIDER® Q2™ MultiSet | and then tighten the screws. You may need to reposition the Clamp repeatedly until you identify the best spot. The microphone must be positioned vertically and not horizontally. English 3. Search for Bluetooth headsets on your GPS device by following the device’s instructions. Please consult your GPS device’s User Manual for more information. 4. If your GPS device prompts for a PIN or Passkey enter 0000 (four zeros). 5. Your GPS device will confirm that pairing has succeeded.
| SCALA RIDER® Q2™ MultiSet side, near speaker [A]. Then place the speaker [B] underneath the padding. 4. Use the pre-moistened Towelette to clean the helmet area where you want to install the Glue Plate. Allow to dry thoroughly. Speaker B 5. Peel the foil cover from the Glue Plates’ adhesive pad. 6. Place the Glue Plate into position according to #3. Press firmly 15 seconds on all 3 parts of the Glue Plate. Speaker A 7. The adhesive pad bonds to full strength over the next 24 hours.
SCALA RIDER® Q2™ MultiSet | USING THE INTERCOM Making Intercom calls GENERAL USAGE GENERAL FUNCTIONS DESIRED RESULT: Turn on the headset Turn off the headset Increase the volume Decrease the volume To start a Buddy Intercom call with the Primary Buddy while the headset is on Standby you can either: REQUIRED ACTION: Press the CTRL Button steadily for at least three seconds Press the CTRL Button steadily for at least three seconds Short press the Volume Up Button VOICE CONNECT: Start talking A Buddy Inte
| SCALA RIDER® Q2™ MultiSet You can manually reconnect at any time by pressing the MC Button (single tap for Primary Buddy and double tap for Secondary Buddy). Enable/Disable Voice Connect feature Press and hold the Volume Up and Down Buttons simultaneously until you hear a beep. The default status is Voice Connect enabled. NOTE: The Enable/Disable Voice Connect feature affects both the Intercom and the mobile phone functionality.
SCALA RIDER® Q2™ MultiSet | None Headset is off Alternating Red/blue flashes Mobile phone/GPS Pairing mode While no call is on the headset (either mobile phone call or Intercom call), press and hold the MC Button on your headset for three seconds to turn on the radio. The radio tunes in to the last radio station you were listening to. With some phones you should wait a few seconds after ending a call before turning on the Radio.
| SCALA RIDER® Q2™ MultiSet • Select the station you wish to replace by tapping the MC button until you find the station you want to replace. • Search for a new station as described above. • Tap the MC Button within 20 seconds of finding the station to save the current station. SUPPORT For additional information please visit our website at www.cardosystems.com FAQ: www.cardosystems.com/faq or contact us at: support@cardosystems.
SCALA RIDER® Q2™ MultiSet | IC RF Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2) this device must accept any interference, including interference that may cause undesired operation of the device.
| SCALA RIDER® Q2™ MultiSet pense (including attorneys fees) and holding Cardo harmless for any bodily injuries, harm or death as well as losses or damages in goods, to any Vehicles including your own, or to any property or asset that belong to you or to third parties, any of which may result from using the Device under any circumstances or conditions and irrespective of jurisdiction.