G4™ Instructor Kit User Guide
TABLE OF CONTENTS 1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 7. HEADSET STATUS LIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2. CONTENTS OF THE RETAIL BOX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 8. PAIRING THE SPEAKERPHONE, INSTRUCTOR AND TRAINEE HEADSETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Congratulations, and thank you for choosing the scala rider G4 Instructor Kit for motorcycle driving schools. The scala rider G4 Instructor Kit contains one set for the Instructor and an additional set for a trainee riding on a motorcycle (or 2 trainees on 2 separate motorcycles, depending on the Kit you have purchased) The headset units included in the box are already factory paired and ready for immediate intercom use.
Bluetooth Speakerphone (Instructor) 2.
3 Microphone sponges: 2 Flat sponges for full-face helmets and round sponge for other helmet types User Guide, Warranty and Registration form Each Trainee’s set contains: Wall charger plug USB adapter cable Allen wrench Velcro pads Glue plate Pre-moistened Towlette Carry pouch 2 Microphone sponges: Flat sponge for full-face helmets and round sponge for other helmet types IMPORTANT: The Instructor and Trainee headsets are waterproof and dustproof devices (certified as IP67).
4. BASIC SETUP AND CONFIGURATION 4.1 GENERAL FUNCTIONS – HEADSET DESIRED RESULT REQUIRED ACTION Turn on the headset Press the Control Button steadily for at least four seconds LED indication: Three blue flashes. Audio feedback: Ascending tone (low-high). Turn off the headset Distinguish between the Instructor and Trainee’s units Press the Control Button steadily for at least three seconds LED indication: Three red flashes. Audio feedback: Descending tone (high-low).
5. GETTING STARTED 5.1 MOUNTING THE HEADSET ON A HELMET The Helmet clamp that includes your microphone and speakers must first be mounted on left part of the helmet. Once mounted, the headset unit can be attached or detached from the clamp at any time. There are two methods that can be used to attach the clamp to the helmet: Standard Method: Recommended for most helmet types. Glue Plate Method: Recommended for helmets to which the standard method cannot be applied, using the Glue Plate included in the box.
7. The adhesive pad bonds to full strength over the next 24 hours. Therefore it is recommended to not use the headset during this 24 hour period. 8. Fasten the Clamp to the Glue Plate using the Allen screws that were previously removed. 5.2 POSITIONING THE MICROPHONE AND SPEAKERS The microphone must be positioned in front of the center of your mouth as Speaker A detailed above.
6.1 USING THE INSTRUCTOR’S HEADSET – CAR OPTION For use while driving a car, both the Speakerphone and Instructors windshield mount should be attached onto the car’s windshield using the suction cups on the back. Secure the Speakerphone and Instructors windshield mount onto the windshield of the car by pressing the suction cups firmly against the glass.
7. HEADSET STATUS LIGHTS LED Indication Status None Headset is off 1 blue flash every 3 seconds Standby – No Intercom call is in progress 2 blue flashes every 3 seconds Intercom Call is in progress 1 red flash every 3 seconds Standby - Battery is low 2 red flashes every 3 seconds Low battery while an Intercom call is in progress Solid red Charging 8. PAIRING THE SPEAKERPHONE, INSTRUCTOR AND TRAINEE HEADSETS 8.
** This step applies only to the scala rider G4 Instructor Kit package for 2 trainees, referred to in the manual as trainee 1 and trainee 2. NOTE: The scala rider G4 Instructor Kit, contains two or three factory paired G4 headsets, depending on the type of Kit purchased. If you did not change the original pairing settings, you can skip the steps below and proceed with how to use the Intercom: 8.2 PAIRING THE BLUETOOTH SPEAKERPHONE TO THE INSTRUCTOR’S HEADSET 1.
9. RESET PAIRING (DELETE ALL PAIRING DATA) You can delete all of your pairings at any time as follows: 9.1 RESETTING YOUR HEADSET 1. For resetting any given headset, please make sure that the remaining headsets are turned off. 2. With the headset turned ON, press and hold the Control Button for at least six seconds until the Red and Blue Lights begin rapidly alternating. 2. Press and hold the Volume Up Button for three seconds. 3.
IMPORTANT NOTE • In order to communicate with Trainee 2 headset, Trainee 1 headset must be operational. * This process may take up to one minute ** Refers to the scala rider G4 Instructor Kit package for 2 trainees 11. SUPPORT For additional information please visit our website at www.cardosystems.com FAQ: www.cardosystems.com/faq or contact us at: support@cardosystems.com Phone: USA and Canada: + 1-800-488-0363 International: +4989 450 36819 12.
FCC RF Radiation Exposure Statement: Operation is subject to the following two conditions: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 1) this device may not cause interference and Industry Canada (IC) Statement 15.
You are irrevocably releasing, indemnifying from any liability, loss, claim and expense (including attorneys fees) and holding Cardo harmless for any bodily injuries, harm or death as well as losses or damages in goods, to any Vehicles including your own, or to any property or asset that belong to you or to third parties, any of which may result from using the Device under any circumstances or conditions and irrespective of jurisdiction.
Disclaimer of Warranty CARDO DISCLAIMS ALL EXPRESS AND IMPLIED WARRANTIES WITH REGARD TO THE ENCLOSED DEVICE, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT. THE DEVICE AND ITS ACCESSORIES ARE PROVIDED “AS IS” AND “AS AVAILABLE” WITHOUT WARRANTY OF ANY KIND BEYOND THOSE ASSUMED IN THE ENCLOSED MANUAL.