™ TeamSet PRO ™ communication in motion ™ Gebrauchsanleitung Guide d’Utilisation Guida di Avvio Guia de Usario User Guide QG TSpro 002 - QG0xx.
© Cardo Systems, Inc. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. Any use of such marks by Cardo Systems, Inc. is under license. Other trademarks and trade names are those of their respective owners. 2 ® ™ scala rider TeamSet PRO QG TSpro 002 - QG0xx.
Congratulations and thank you for choosing the scala rider TeamSet pro Bluetooth® Headset package for bikers. CONTENTS OF RETAIL BOX English INTRODUCTION Volume Up Two Headsets Charging Jack This User Guide will help you operate the headset, but you should first familiarize yourself with the Bluetooth functionality of your cellular phone and/or GPS device before using the scala rider TeamSet pro.
SET UP AND CONFIGURATION 1 Dual Wall Charger 2 Allen Wrenches 2 sets of Velcro Pads 2 MP3 Cables GPS 2 MP3 Cable Holders Mobile phone 2 Glue Plates 2 Pre-moistened Towelettes 2 Carry-Pouches 4 Microphone Sponges Flat sponge for full-face helmets and round sponge for other helmet types User Guide, including Warranty and Registration form MP3 player Driver-toPassenger Full-duplex Intercom Connection IMPORTANT: Your headsets are water-resistant, designed for use under moderate rain or snow conditions.
NOTE: If the Pairing process is not completed within one minute the headset will return to Standby mode. SET UP FOR MOBILE PHONE CALLS: PAIRING If you have a Bluetooth enabled mobile phone and would like to make and receive phone calls using the scala rider TeamSet pro, you must first pair your headset to the mobile phone. NOTE: If you have a compatible Bluetooth GPS device you wish to use with the scala rider TeamSet pro, please skip this step, and continue ahead to SET UP FOR BLUETOOTH GPS DEVICE.
5. Your GPS device will confirm that pairing has succeeded. The headset will begin flashing slowly in Blue. 6. If you wish to use a Bluetooth mobile phone to make and receive calls through the headset, you must now pair your mobile phone to your GPS device by following your GPS and/or mobile phone’s instructions. NOTE: If the Pairing process is not completed within two minutes the headset will return to Standby mode. RESET PAIRING You can delete all of the headset’s pairings at any time. 1.
If you have purchased a helmet clamp version with the corded microphone, please proceed as follows: ATTACHING THE CORDED MICROPHONE CLAMP ON A FULL-FACED HELMET If you are using the corded microphone version, you must first make sure your helmet clamp is attached to your helmet as described in previous section (ATTACHING THE CLAMP ON THE HELMET). Clean the exact spot on the internal padding of the helmet, opposite your mouth, where the microphone will be placed and proceed as follows. a.
ATTACHING AND REMOVING THE HEADSET FROM THE HELMET CLAMP ATTACHING: Slide the headset downwards along the sliding panel until a clicking sound indicates that the headset is locked in place. REMOVING: Your headset can be removed for charging and storage by pressing your finger gently against the tab and sliding the headset up with the other hand. We recommend that you remove the headset from the helmet when not in use.
Receiving Intercom calls If you are not speaking with any one, once the other party tries to initiate a Buddy Intercom call, the call will begin immediately. MAKING AND RECEIVING MOBILE PHONE CALLS Answer a call Reject a call Terminate a call Voice Dial TROUBLESHOOTING THE INTERCOM: First, make sure your microphone is located properly in front of the center of your mouth. The scala rider TeamSet pro is designed for use in loud environments.
1 blue flash every 3 seconds Standby – No call is in progress 2 blue flashes every 3 seconds Call being initiated or in progress 1 red flash every 3 seconds Battery is low 2 red flashes every 3 seconds Call being initiated or in progress and battery is low Solid red Headset is being charged Using the MP3 player with your headset Your scala rider TeamSet pro headset can be connected to an MP3 player device by plugging it to the Helmet Clamp’s jack with the MP3 cable.
Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
referred to as “Vehicle”) requires your complete and undivided attention. Cardo Systems, Inc.