scala-rider TeamSet C A R D O S Y S T E M S I N C .
INTRODUCTION This Quick Guide will get you started using the scala-rider TeamSet. For more detailed information, including safety precautions, please download the User Manual from our website at www.cardowireless.com. Before using the scala-rider TeamSet, please familiarize yourself with the Bluetooth® functionality of your cellular phone. The retail box of the scala-rider TeamSet contains two headset units: One device for the driver and a second device for the passenger.
COMPONENTS Intercom Button Control Button Volume Up Status Light Charging Jack (Here shown with closed cover tongue) Sliding Panel Volume Down Tab Right speaker (long cord) Microphone Sliding Plate Left speaker (short cord) One headset for the driver and one headset for the passenger. NOTE: The use of two speakers may be illegal in certain jurisdictions. Please check the local regulations and act accordingly.
IMPORTANT The scala-rider TeamSet is a water-resistant device, designed for use under moderate rain or snow conditions. However, the headset is not waterproof and should not be used under severe weather conditions. The cover tongue protecting the Charging Jack should be kept tightly closed at all times to prevent moisture from entering the device. BEFORE USING (CHARGING THE HEADSET) Make sure that both headsets are fully charged for at least 5 hours before initial use. 1.
TURNING THE DRIVER HEADSET ON FOR THE FIRST TIME The driver unit (yellow logo): The driver unit permits two communication modes: • Mobile Phone connections with third parties • Intercom connection with the passenger In order for the headset to work with your cellular phone, they must first recognize each other. This process is called “pairing”, and only needs to be performed once for each phone. 1. Turn on your phone and make sure its Bluetooth function is activated. 2.
The Passenger Unit (green logo): This unit is solely intended for intercom connection with the driver and it cannot initiate or receive a phone call. To turn on the Passenger Unit, press the Control Button until the blue Status Light illuminates. NOTE: The Driver and Passenger Units are already factory-synchronized for Intercom communication with each other, and do not require any synchronization by you.
ATTACHING THE SCALA-RIDER UNITS TO YOUR HELMETS Perform this procedure for both the driver and passenger helmets. 1. Use the enclosed Allen Wrench to loosen the two screws on the Back Plate. Allen Wrench Back Plate 2. Slide the Back Plate between the internal padding and the external shell of the helmet. (If the external shell is too thick, use the supplied plastic Extension Pad by loosening the screws and fitting the extention pad between the Back Plate and the main body of the clamp). 3.
4. Slide the headset downwards along the sliding panel until a clicking sound indicates that the headset is locked in place. REMOVING THE HEADSET FROM THE HELMET Your headset can be removed for charging and storage by pressing your finger gently against the tab and sliding the headset up with the other hand. We recommend that you store your headset in the enclosed carrying pouch when not in use.
DRIVER’S UNIT FUNCTIONS DESIRED RESULT: G E N E REQUIRED ACTION: R Turn on the headset Turn off the headset Increase the volume Decrease the volume P H O Answer a call Reject a call Terminate a call Voice Dial Redial Enable/Disable voice command feature A L F U N C T I O N S Press the Control Button steadily for at least 6 seconds Press the Control Button steadily for at least 3 seconds Short press the Volume Up Button. Short press the Volume Down Button.
DRIVER’S UNIT FUNCTIONS (continued) DESIRED RESULT: I N T E REQUIRED ACTION: R C Start using the intercom Terminate the operation of intercom Conference Call (add passenger to an active call) End Conference Call (release passenger from a conference call) Enable/Disable Voice Command feature O M F U N C T I O N S During standby, start speaking loudly to activate the intercom Stop speaking. The audio connection will be terminated within 25 seconds.
DRIVER’S UNIT STATUS LIGHTS The Driver Headset uses the following Status Lights to display its current state: Status Light None Alternating Red/blue flashes 1 blue flash every 3 seconds 2 blue flashes every 3 seconds 1 red flash every 3 seconds 2 red flashes every 3 seconds Steady red Status Headset is off Pairing mode Standby – No call is in progress Call being initiated or in progress Battery is low Call being initiated or in progress and battery is low Headset is being charged PASSENGER’S UNIT STATUS L
AUDIO TONES With the exception of the actions below, all other actions are followed by a single tone to confirm that the headset has accepted the command.
Cannot terminate calls using the intercom button Can’t answer phone calls using the Voice Command (VC) feature. I cannot perform redial 3. Verify that the scala-rider headset is the paired headset to your phone. 4. Reconnect the phone and headset by short pressing the Control Button on the headset, or connecting them manually by using your phone’s menu. 5. Check the definitions and settings on your phone. 6.
Battery does not provide at least five hours of talk time I’m trying to reject incoming calls by remaining silent, but the phone continues to ring. Red Status Light does not light steady when charger is connected. I hear crackling noises Sound deteriorates when the phone is in my back pocket. 1. Make sure your scala-rider headset is fully charged. Charging time is up to 5 hours for an empty battery. When the headset is connected to the charger and it is fully charged, the red Status Light turns off. 2.
The party I am speaking to complains about insufficient audio quality pocket or at least to a front pocket on the same side you wear your headset. 1. Close helmet cover under high speed conditions. 2. Make sure the microphone is in front of your mouth. The microphone should be positioned vertically as described on page 7. Intercom-Related Problems (driver/passenger) Cannot initiate conversation 1. Try speaking louder. with other party 2.
Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. | NOTICES 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Industry Canada (IC) Statement 15.
Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device. IC RF Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance.
WAIVER AND GENERAL RELEASE By using the scala-rider TeamSet Driver you will waive substantial legal rights including the right to sue. Please read the following carefully before using the device. If you do not accept all terms of this agreement, you should immediately return the product for a full refund. By using the headset you agree to be bound to this agreement and forfeit the right to sue.
Device under any circumstances or conditions and irrespective of jurisdiction. Cardo will not be responsible for any physical damages, irrespective of reasons, conditions or circumstances, including malfunctioning of the Device, and all risks associated with operating it rest solely and entirely with the user of this Device, irrespective of whether the Device is used by the original purchaser or any third party.
altering substance, and will not carry, use or consume these substances before or during the use of the Device. 4.
Limitation of Liability IN NO EVENT SHALL CARDO BE LIABLE FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF THE DEVICE, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
PLEASE NOTE: THE USE OF THIS PRODUCT IS AT YOUR SOLE RISK AND MAY BE ILLEGAL IN CERTAIN JURISDICTIONS. ALL WAIVER PROVISIONS CONTAINED IN THE COMPREHENSIVE USER MANUAL APPLY. IF YOU ARE UNWILLING TO ACCEPT ANY OF THE SAID WAIVER CONDITIONS YOU MAY RETURN THE PRODUCT FOR A FULL REFUND ACCORDING TO COMPANY POLICY TERMS. SUPPORT For additional information visit our website at www.cardowireless.