User's Manual

ManualsBrandsCapricorn Electronics ManualsElectronicsMonitoring and Tracking device

ENVOY geo OPERATING Instructions

Your ENVOY geo is a very powerful device that can track, monitor and provide remote control from any cellular phone. In

order to make it as accessible and as simple to use as possible, we have provisioned ENVOY at the factory to perform the

more common functions "out of the box". It has many capabilities that we do not mention here, so contact us for any special

requirements. First follow the separately provided instructions for the installation of the ENVOY geo into your craft.

Loading SIMCARD

f your ENVOY geo did not ship with a SIMCARD, follow the steps below. NOTE: YOU MUST disconnect all external power

supply connections when changing SIMCARD. This may mean unbolting the positive terminal or disconnecting the boat's

battery, while you do this.

Remove screws as shown in FIG. 1. Carefully slide out the ENVOY circuit board.

Make sure the Battery is disconnected as seen in FIG. 4.

Remove the black Battery holder by releasing the clips from the main board one at the time. Locate the

SIMCARD holder see FIG. 2. Gently push the silver slide toward main holder body to release. Swivel

SIMCARD carrier up.

Insert an activated SIMCARD with the golden contact side facing downwards and the cut corner facing up as

shown. See FIG. 3

Hinge carrier closed. Slide silver slide back away from main body to lock.

Next, take the small white plug from standby battery and slide it into the power socket as shown in FIG 4.

This only goes in one way. Do NOT force.

You are now ready to load the phone numbers. Test with just one cellphone first, then load others later as

required.

Summary of content (6 pages)

PAGE 1
ENVOY geo OPERATING Instructions Your ENVOY geo is a very powerful device that can track, monitor and provide remote control from any cellular phone. In order to make it as accessible and as simple to use as possible, we have provisioned ENVOY at the factory to perform the more common functions "out of the box". It has many capabilities that we do not mention here, so contact us for any special requirements.
PAGE 2
Set up your phone to send a text message (SMS) TO the phone number issued with the SIMCARD that you just loaded into ENVOY. The SIMCARD phone number will have been issued along with the SIM card by the network provider. The first message you must send ENVOY is your cell phone number. Send the following text message:: ADDPHONEn<>88888888<>+(country code)(area code)(your cellphone number) (n is ph 1 to ph 4.) eg : ADDPHONE3 88888888 +121234567899 (This is loaded as ph # 3) Spaces are indicated by <>.
PAGE 3
CHANGING PASSWORD To change the password, send ENVOY the following text message; PASSWORD<>OLD password<>NEW password eg: PASSWORD 88888888 12345678 SETTING and USING the GEO-FENCE From your cellphone, send ENVOY the following Geo-Fence command: 'SET' It will respond with a confirmation SMS that it has a new HOME location for the geo-fence. That’s all…. ENVOY will now send a transgression report if it moves outside the geo-fence radius.
PAGE 4
the highest alert geo-fence monitoring mode and lastly a hyperlink to Google Map that contains the Latitude and Longitude in a degrees and decimal degrees. Cursor your internet enabled smart phone browser over the hyperlink and click to see the current position displayed on Google Map. You can copy the link straight onto Google Earth if running on a PC, or use Bluetooth to transfer the hyperlink from your cellphone to your PC, where you can click on the hyperlink and view the position on a map.
PAGE 5
PLE Power Loss alert ENABLE. PLD Power Loss alert DISABLE. EXTVOLT ON//v.v Alarm voltage setpoint for low voltage alert. Sets value to send alarm. Eg EXTVOLT ON//11.8 Use in conjunction with PWRDEL delay time value to avoid transient alarms. OFF/ON. E1D n Add a Time delay of n minutes to switch n. Use to avoid transient alarms. DATARESET Resets configuration to Factory default. Use with care. Custom changes will be lost. CTXSO Change Switch (n) OPEN message to "msg".
PAGE 6
IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter” NOTE: ENVOY Marine accepts no liability for the applications or uses made by its products. We recommend that you always obey local laws relating to tracking and in particular disablement of vehicles by remote control.