User's Manual

3-Button
Garage
Door
Remote
Control
Model
G6T3
ln this
package,
you
will find
a
Skylink'
garage
door
transmitter
with 3V
lithium
battery,
a mounting
bracket,
a visor
clip and
a double
sided tape.
E
lsatteryinsioel
A
lt-",:l:l"r
visorcrio
Double
Sided Tape
There
are three
buttons
on transmitter
G6T3,
each
button
can be
programed
to control
Skylink
garage
door
receiver
Smad ButtonrM
GB-318
or GB-318-3
or
Skylink
garage
door opener
directly.
Follow
one or
more instructions
below
in Section
2
to
program
transmitter
G6T3 to the
recetver
or receivers you
want
to
control.
You need
to
do the
programming
in
order to
add
the transmitter
-
remote
control to
a
receiver.
Refer
to the receiver
Smart
Buttonru
GB-318
useds
instruction
to
set up the unit.
Smart ButtonrM
GB-318
can
learn
up to 10
remote
controls.
To
program
the
transmitter
to the
receiver,
follow
the
instructions
below:
1. Press
the
learn
button
on the
side
of the
Smart ButtonrMGB-319.
2.
Once the learn
button ts
pressed,
the
LED will
llash
quickly.
Release
the
learn
button.
3. Within
30 seconds,
press
any
one
of the
3 buttons
on the transmitter
that
you
want
to
program
to
the
receiver.
Once the
remote
control is
programmed,
the LED
will
flash
slowly,
in the
same
way
as it flashes
in
standby
mode.
You
may now
operate
the
garage
door opener
with this
new
remote
control.
To
program
this
transmittei.to
conirol
another
receiver.
repeat
process
(1)
to
(+)
to
program
another
button
on the
remote
control.
You need
to
do the
programming
in
order to
add
the transmitter
to a
Skylink@
Garage
Door
Opener.
Skylink@
Garage
Door
Opener can
learn
up to
16 remote
controls.
To
program
the
transmttter
to the
Garage
Door
Receiver,
follow
the
instructions
below:
1. Press
the
LEARN/SET
button
once
on the
garage
door
opener.
2.
Once the
LEARN/SET
buttton
is
pressed,
the
LEARN
LED
will ftash.
You
may
release
the LEARN/SET
button.
3. Within
30 seconds, press
any
one
of the
3 buttons
on the
transmitter
that
you
want
to
program
to the
receiver.
4. Once
the transmitter
is
programmed,
the
LEARN
LED will
turn
off.
5. You may
now
operate
the
garage
door
opener
with
this new
transmitter.
6. To
program
a transmitter
to
control
another garage
door
opener,
repeat
process
(1)to
(a)
to
program
another
button
on the transmitter.
Smart
ButtonrM
G8.318
To
program
the
transmitter
to
a Skylink
Garage
Door
Receiver
Smart
Buttonru
GB-318-3 (3
doors)
,
please
follow
the
user's
instruction
for the
model
GB-g1g-3.
To
program
the transmitter
to
the
Skylinko le
senes
Garage
Door
Opener,
please
follow
the
user's
instruction
from
the
Garage
Door
Opener.
Q:
What
can I
do if
the door
opener
does not
react
after I
press
the
bufton on
the transmitter
?
A:
-
Ensure when
the button
on
the transmitter
is
pressed,
the red light
on the
transmitter
comes on.
Otherwise,
check if the
battery
is inserted
properly.
-
Make
sure
the
correct
button
on the
transmitter
is
pressed.
-
Ensure
the
wires
that were
previously
connected
to the
wall mounted
door
control
are nol
loose.
-
Ensure
the
transmitter
has
been
programmed
to the
receiver.
Refer
to
section 2
for how
to
program
a transmitter
to the
recejver.
3 Volt lithium
battery
(CR
2032)
(inctuded).
It
is time
to change
the
battery when
the
red LED
on
the transrnitter
does
not
turn
on when
either
button is
pressed.
lf
you
would like
to
-
find
out the
up-to-date
specifjcations
-
know more
about
leatures
and
applications
-
download
documents,
i.e.
user's
instructions
-
order
Skylink
products
or iJ
you
have
difficulty getting products
to work,
please:
1. visit
our FAQ
section
at
www.skylinkhome.com,
or
2. email
us at [e-mail],
or
3. call
ourtoll free
at 1-800-304-1187
from
Monday
to Friday,
9 am to
5
pm
EST
Fax
(800)
286-1320
CUSTOMER
SERVICE
17
Sheard Avenue,
Brampton,
Ontario,
Canada
L6y
1J3
Email:[e-mail]
http:i/www.skylinkhome.com
P/N.101z,&2
Patent Pending
This
devicecomplies
with
Part 15
ofthe Fcc
Rules.
operation
is subjectto
thefollowing
hryocondttions:
(1
)
Thls
device may
not
cause harmfur
interference,
and
(2)
Thrs
device
must accept
any interference
received,
including interference
that
maycause
undesiredoperation.
WARNING;
changes ormodifrcationsto
this
unit
not expressryapproved
bythe
party
responsibre
forcompriance
courd
void the
user's
authorilyto
operatethe
equ
pment.
NOTE:
Thisequipment
has
beentested
and foundto
complywiththe
rimitsforacrass
Bdigitarcrevice, pursuant
to Pad 1
5 01 the Fcc
Rures
These
rimits
are designed
to
provide
reasonabre protection
against
harmfur
rnterference
in a residential
installatlon.
This equipment generates,
uses
and can radiate
adio frequency
energy
and, if not installed
and
used in
accordance
with
the instructions,
maycause
harmful interference
to
radio
communications
However,
there is
no
guarantee
that
interference
will not
mur in
a
particular
installation.
lf this
equipmentdcs
cause harmful
interferenceto
radio
orterevision
rrception,
which
can be
determined
by turning
the equipment
off and
on, the user
is encouraged
to try
to correct
the interference
byone
or more
or the foilowing
merures:
-
Reorient
or
relocate
the receiving
antenna.
-
lncrease
the
separaUon
behryeen
the
equipment
and
receiver.
-
Connect
the
equipment
into
arl outlet
on a circuit
different
from
that
to which the
receiver
ts connected.
-
Consult the
dealer or
an
experienced
radio/Tvtechnician
for
help.
lf, within
one
year
from
date
of
purchase,
this
product
shourd
become
defective
(except
battery),
due to
faulty
workmanship
or
materials,
it
will
be repaired
or
replaced,
without
charge.
Proof
of
purchase
and
a Return
Authorization
are
required.
Learn
Button
o
o
d
lfif,
I[!