Toy Caboose Stroller Instruction Manual These instructions are for the following Joovy Style Numbers: 042, 043 Please read these instructions in their entirety to ensure the proper assembly and use of your toy. Keep these instructions for future reference. Joovy • 2919 Canton Street • Dallas, TX 75226 • (877) 456-5049 • Fax: (214) 761-1774 E-mail: customerservice@joovy.com • Website: www.joovy.
! WARNINGS • This product is a TOY stroller for dolls or stuffed toys ONLY. • NEVER use this toy to carry a baby or child for any purpose whatsoever. Death or Serious Injury may occur. • Maximum weight allowed = 5 pounds in EACH seat. • DO NOT stand on platform. Riding is for dolls or stuffed toys ONLY. • This product contains small parts. Adult assembly is required. • The maximum weight that can be carried in the storage basket is 5 pounds • Discard all packaging materials properly.
Assembling and Using your Stroller To ensure safe operation of your stroller, please follow these instructions carefully. Unpacking the Product • Carefully remove stroller and all parts from the box and plastic bag. • Remove the cardboard packing materials from the ends of the frame. • Identify the parts (stroller, canopy, tray, front wheels (2), rear wheels (2), rear axle, washers (2), axle locks (2), axle caps (2), hubcaps (2), car seat carrier support and documents with the pictures in Figures 1 and 1A.
Installing the Rear Wheels • Turn your stroller upside down so that it is resting on the seatback. • Locate the rear axle and slide it through the holes into the frame near the platform. • Locate a metal washer and slide the washer onto one end of the axle. See Figure 3. • Locate a rear wheel and slide the wheel onto the axle. IMPORTANT NOTE: The left and right side wheels are slightly different. The correct wheel will have the arrow shapes on the tire tread pointed towards the REAR of the stroller.
Installing and Operating the Canopy • To attach the canopy, orient the canopy on the stroller with the wide front edge toward the front of the stroller. • Line up the fittings on the canopy with the fittings near the center of the stroller and slide the canopy on until it snaps into place. See Figure 7. • The canopy will open, close and ratchet forward or backward • To remove the canopy, slide the canopy off the fittings.
Adjusting the Footrest The footrest can be adjusted to two positions – horizontal or all the way down. • To place the footrest into the horizontal position, pull up on the footrest and the metal bar until the footrest catches into position. See Figure 10. • To place the footrest all the way to its down position, pull up on the footrest to release the bar from the slot, and then slowly lower the footrest.
Seatback Positioning The front seat has two positions. • To place the seat in the upright position, push the bar on the rear of the seat toward the front of the stroller and rotate the seatback towards the front of the stroller until this bar is locked in its lowest position. See Figure 12. • To recline the seat, pull the bar on the rear of the seat toward the rear of the stroller and rotate the seatback down until this bar is again in its lowest position.
Using the Bench Seat • Push the bench seat to its most rearward position. • Position the doll on the bench seat facing backward with their feet on the platform. • Unlatch the seat belt buckle by pressing down the button in the center of the buckle and removing the male sides of the buckle. • Place the seat belt completely around the doll’s waist, place the crotch strap between the doll’s legs and snap the buckle together. See Figure 14.
Using the stroller as a Doll Car Seat Carrier • To use the stroller to carry a doll car seat carrier, you must replace the Front Tray with the Car Seat Carrier Support. • Remove the Front Tray by pressing in on the buttons under the female fitting and pulling the tray off the brackets. • Line up the Car Seat Carrier Support to the metal tubing on the front of the stroller and push inward until the support snaps into place. See Figure 16.
Folding the Stroller • Orient the stroller with the handle bar closest to you. • Place the canopy into its closed position and push it as far forward toward the front of the stroller as it will go. • Pull upwards on the trigger mechanisms on both sides of the stroller. See Figure 19. • While these mechanisms are in the upward position, push forward and down on the stroller using the handle bar.
Maintenance All of the fittings, snaps, locks, rivets, and other hardware and plastic parts on the stroller should be inspected periodically to insure that they are secured properly and not damaged or malfunctioning. The seat belts and safety harnesses, as well as all other straps and fabric items and their stitching should also be inspected periodically to insure that they are secured properly and not loose, torn or otherwise damaged.
2919 Canton Street • Dallas, TX 75226 • (877) 456-5049 • Fax: (214) 761-1774 E-mail: customerservice@joovy.com • Website: www.joovy.com ©Joovy 2006 • Document Version 1.