Océ User Manual Paper Folding Unit-F1 Operating information
Copyright Copyright 2011 by Canon Inc. All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or by any information storage or retrieval system without the prior written permission of Canon Inc. © 2011, Océ All rights reserved. No part of this work may be reproduced, copied, adapted, or transmitted in any form or by any means without written permission from Océ.
Contents Contents Chapter 1 Preface.................................................................................................................5 Notes for the reader...................................................................................6 Naming conventions for finishers (commercial naming and naming in User Interfaces)..........................................................................................8 Chapter 2 Use the folder..........................................................
Contents 4
Chapter 1 Preface
Notes for the reader Notes for the reader Introduction This manual helps you to use the Paper Folding Unit-F1. The manual contains a description of the product and guidelines to use and operate the Paper Folding Unit-F1. Definition Attention-Getters Parts of this manual require your special attention. These parts can provide the following: • Additional general information, for example, information that is useful when you perform a task. • Information to prevent personal injuries or property damage.
Notes for the reader Word Icon Indicates Caution Ignoring this warning could cause injury or damage to property. Note Indicates additional important information. The use of heat-resistant gloves is mandatory when you carry out these actions.
Naming conventions for finishers (commercial naming and naming in User Interfaces) Naming conventions for finishers (commercial naming and naming in User Interfaces) Hardware and hardware naming in User Interfaces To improve the readability of texts in User Interfaces of operator panels and software, the finishers are generally referred to by their function. The table below shows the naming conventions for finishers (commercial product names and the way these are referred to in User Interfaces).
Chapter 2 Use the folder
The main parts of the folder The main parts of the folder Note: The folder (Paper Folding Unit-F1) can only be used in combination with the stacker/stapler (Finisher-AF1/Saddle Finisher-AF2). Illustration [10] Main parts of the folder Components and their functions Main parts of the folder# 10 Component Function 1 Front door Open this door to remove jammed paper. 2 Folding unit Pull out this unit to remove jammed paper. 3 Folder main tray This tray can receive folded prints.
The folding modes The folding modes Overview of the folding modes The folder supports the following folding modes. Folding modes# Folding mode Illustration Remarks Z-fold Only Z-folded A4R, LetterR and Legal sheets can be sent to the folder output tray. Z-folded A3, B4 and 11" x 17" sheets must be sent to the output trays of the stacker/stapler. Tri-fold in Tri-fold in sheets can be sent either to the folder output tray or any output tray of the stacker/stapler.
The folding modes Legend for the above illustration# English text Translation Leading Edge Length Leading Edge Length Feeding Direction Feeding Direction Overview of the Z-folded areas# Feeding method Remarks If paper that has been Z-folded is included in the output, the sheets may not be aligned when output. Platen glass = Glass plate Feeder = ADF Tri-fold in The illustration below shows the feeding direction and fold method.
The folding modes Legend for the above illustration# English text Translation Leading Edge Length Leading Edge Length Feeding Direction Feeding Direction Overview of the tri-fold in areas# Feeding method Remarks Platen glass = Glass plate Feeder = ADF Tri-fold out The illustration below shows the feeding direction and fold method.
The folding modes Legend for the above illustration# English text Translation Leading Edge Length Leading Edge Length Feeding Direction Feeding Direction Overview of the tri-fold out areas# Feeding method Remarks Platen glass = Glass plate Feeder = ADF Double parallel fold The illustration below shows the feeding direction and fold method.
The folding modes Legend for the above illustration# English text Translation Leading Edge Length Leading Edge Length Feeding Direction Feeding Direction Overview of the double parallel fold areas# Feeding method Remarks Platen glass = Glass plate Feeder = ADF Chapter 2 - Use the folder 15
The folding modes 16 Chapter 2 - Use the folder
Chapter 3 Troubleshooting
Labels inside the folder Labels inside the folder Introduction If a paper jam occurs in the folder (Paper Folding Unit-F1), the operator panel will display the location of the paper jam and a procedure to clear the paper jam. Follow the procedure on the operator panel to clear the paper jam. The procedure contains references to the error locations you must check, for example A2 or A3. The illustration below shows an overview of all the error locations.
Labels inside the folder [24] Front Cover = Front cover Overview of the error locations and their labels The table below describes the error locations in the order these must be checked in general. Depending on the paper jam, the order to check the error locations can be different. Always follow the instructions on the operator panel to clear a paper jam.
Clear a paper jam in the folder Clear a paper jam in the folder Introduction If a paper jam occurs in the folder, the operator panel will display the location of the paper jam and a procedure to clear the paper jam. Follow the procedure on the operator panel to clear the paper jam. The procedure below describes how to clear a paper jam in the folder. Warning: When you remove jammed originals or paper, take care not to cut your hands on the edges of the originals or paper.
Clear a paper jam in the folder Step Action 3 Turn the dial (M-A3) in the direction of the arrow (counterclockwise). 4 Remove any jammed paper. 5 Pull out the paper folding unit (M-B1). 6 Open the left-hand guide (MB2).
Clear a paper jam in the folder Step Action Illustration 7 Remove any jammed paper. When there is a paper jam in the inside guide When there is a paper jam in the outside guide 22 8 Close the left-hand guide (MB2). WARNING When you close the guide, be careful not to get your fingers caught, as this may result in personal injury. 9 Open the right-hand guide (MB3). Open the guide as far as possible.
Clear a paper jam in the folder Step Action Illustration 10 Remove any jammed paper. When there is a paper jam in the inside guide When there is a paper jam in the outside guide 11 Close the right-hand guide (MB3). WARNING When you close the guide, be careful not to get your fingers caught, as this may result in personal injury. 12 Push out any jammed paper toward the exit slot (M-B4).
Clear a paper jam in the folder 24 Step Action 13 Remove the jammed paper. 14 Return the paper folding unit (M-B1) to its original position. WARNING When you return the paper folding unit to its original position, be careful not to get your fingers caught, because this may result in personal injury. 15 Close the guide (M-A2). WARNING When you close the guide, be careful not to get your fingers caught, because this may result in personal injury. 16 Close the front door of the folder.
Clear a paper jam in the folder Step Action 18 Follow the instructions on the operator panel.
Clear a paper jam in the folder 26 Chapter 3 - Troubleshooting
Appendix A Specifications
Specifications Specifications Paper Folding Unit-F1 Note: Whenever a number of sheets is mentioned in the table below, the figure is based on media of 80 g/m² (20 lb Bond). Specifications of Paper Folding Unit-F1# Item Specification Description Integrated folding unit that comes optional in combination with Finisher-AF1 or Saddle FinisherAF2. Supported media sizes for folding • • • • Supported media sizes for passthrough • Maximum: 330.2 mm x 487.
Specifications Item Specification Power source From Finisher-AF1/Saddle Finisher-AF2 Appendix A - Specifications 29
Index Index Conversion table for commercial names and user interface names Conversion table for commercial names and user interface names .................................................8 E Error locations Error locations ................................................18 F Folder Components ...................................................10 Main parts ......................................................10 Folding modes Folding modes ................................................
