Wireless File Transmitter WFT-E2 II Y P O Instruction Manual for Use With EOS-1D Mark IV C To EOS-1D Mark III or EOS-1Ds Mark III Users This instruction manual describes the use of the transmitter when connected to the EOS-1D Mark IV. When using the transmitter with the EOS-1D Mark III or EOS-1Ds Mark III, refer to the PDF manual in the EOS_1DIII_1DsIII folder.
Introduction The Wireless File Transmitter WFT-E2 II is an accessory for EOS-1D Mark IV camera. It gives the camera wireless and wired LAN functionality and adds a USB port, enabling the following operations.
Introduction Functions When Connected via USB External Media Record or backup images onto external media GPS C Connected by a USB cable Y P O Connected via Bluetooth Add the latitude, longitude, altitude, date and time, and other shooting information to images 3
Conventions Used in this Manual These instructions should be followed only after your wireless or wired LAN and FTP server settings are complete. For details on configuring these settings, refer to the documentation provided with the respective equipment. Terms in brackets [ ] indicate button or icon names or other software elements. Brackets also denote camera menu items. Page numbers in parentheses indicate where you can find additional information.
Chapter List Introduction 2 1 Basic Network Settings 15 2 Transferring Images to an FTP Server 29 3 Remote Capture Using EOS Utility 43 4 Remote Capture Using WFT Server 49 5 Linked Shooting 6 Managing Settings Information 65 7 Using External Media 71 8 Using GPS Devices 83 9 Troubleshooting 91 10 Reference C Y P O 61 109 5
Contents Introduction 2 Conventions Used in this Manual ...................................................................................................... 4 Chapter List........................................................................................................................................ 5 Contents............................................................................................................................................. 6 Areas of Use and Restrictions ................
Contents 6 Managing Settings Information 65 Checking Settings ............................................................................................................................ 66 Changing Settings............................................................................................................................ 67 Saving and Loading Settings ...........................................................................................................
Areas of Use and Restrictions To comply with local radio wave regulations in various areas around the world, Canon offers four region-specific versions of the transmitter (WFT-E2 IIA, E2 IIB, E2 IIC, and E2 IID) as described below. Please do not use your model (version) of transmitter in regions it was not designed for. For information on other areas where the transmitter can be used, contact Canon Service Center.
Areas of Use and Restrictions The following actions may be punishable under law. Disassembling or modifying the transmitter, or removing the certification label on it. Do not use the transmitter near other devices that emit radio waves, such as medical equipment or electronic devices. The transmitter may interfere with operation of these devices. Use the transmitter only with a compatible EOS DIGITAL camera.
Safety Warnings The following precautions are intended to prevent harm to you and others as well as damage to equipment. Become familiar with the precautions before using the transmitter to ensure correct and safe operation. Warning Preventing Serious Injury or Death To prevent fire, excessive heat, chemical leakage, or explosion, follow these safety guidelines. • Do not insert metallic objects between electrical contacts of the transmitter, accessories, or connecting cables.
Nomenclature Locking lever Attachment pin USB port Ethernet RJ-45 port Port cover Tightening screw Terminal USB lamp Network lamp Y P O Terminal cap receptacle (Not used with the EOS-1D Mark IV) Transmitter Case C Waterproof/Dustproof USB Cap*2 External Media Case*1 *1: For storing portable hard disks or other devices. *2: Attach this cap before connecting the USB cable in rainy weather or under other adverse conditions.
Attaching to the Camera Turn off the camera before attaching the transmitter. Ensure the camera battery has sufficient charge. If the charge drops below 19%, you cannot transfer captured images or back them up to external media. 1 Open the terminal cover on the camera. 2 Move the lever into the release position. 3 Attach the transmitter. Open the extension system terminal cover and turn it toward the bottom. C 4 Y P O Align the attachment pin with the WFT-E2 II/IIA mounting hole on the camera.
Subsequent Organization of This Manual Click one of the following chapter titles to view the corresponding page. 1 Basic Network Settings (p.15) 2 Transferring Images to an FTP Server (p.29) 3 Remote Capture Using EOS Utility (p.43) 4 Remote Capture Using WFT Server (p.49) 5 Linked Shooting (p.61) 6 Managing Settings Information (p.65) Y P O 7 Using External Media (p.71) C 8 Using GPS Devices (p.
C 14 Y P O
Basic Network Settings Y P O Complete the basic network settings by following transmitter connection instructions on the camera menu screen.
Getting Ready [FTP trans.], [EOSUtility], [WFTserver] The connection instructions help you follow the steps to connect the transmitter to an existing wireless or wired LAN. To connect to a wireless LAN, prepare the wireless LAN terminal (wireless LAN access point or wireless LAN adapter) and computer in advance so that they are ready for you to connect the transmitter to the wireless network. When configuring the basic network settings, bring the transmitter within 3 m / 9.8 ft.
Displaying the Connection Wizard This section describes the process of following the connection instructions. If an error is displayed, refer to “Troubleshooting” in Chapter 9 (p.91) and check the settings. Pressing the shutter button or other camera controls during configuration by the connection instructions will close the connection instructions. Do not press the shutter button or other controls until configuration is finished. On the [5] tab, set [Auto power off] to [Off].
Selecting the Communication Method and LAN Type Selecting the Communication Method Turn the <5> dial to select the communication method, and then press <0>. Select [OK] and press <0> to go to the next screen. • FTP trans. Choose this option to transfer captured images to an FTP server. Images can be automatically transferred as you shoot them, or you can select images to be transfered later. Computer Operating Systems Operation via [FTP trans.
Selecting the Communication Method and LAN Type • WFTserver Choose this option for remote capture over a wireless or wired LAN with the transmitter acting as a server. Additionally, images on a memory card in the camera can be viewed and downloaded to a computer. The camera can be accessed like browsing a webpage, by users at up to three computers. Computer Operating Systems Any computer with a web browser can be used, regardless of the operating system.
Selecting the Communication Method and LAN Type Selecting the LAN Type For [LinkedShot] instructions, refer to page 61. Note that no information about [LinkedShot] is given in this chapter. Turn the <5> dial to select the type of LAN, and then press <0>. Select [OK] and press <0> to go to the next screen. Wireless LAN The [Wireless LAN setup method] screen is displayed. [Connect with wizard]: See p.21 [WPS (PBC mode)]: See p.23 [WPS (PIN mode)]: See p.
Using the Wizard to Establish a Connection Selecting the Wireless Network When you select [Connect with wizard], active wireless LAN terminals in your area are listed, accompanied by information about them. Select the SSID (or ESS-ID) of your desired wireless LAN terminal. 1 2 3 4 1 Select [Connect with wizard]. 2 Select the wireless LAN terminal. Turn the <5> dial to select [Connect with wizard], and then press <0>. To select the wireless LAN terminal, press <0>.
Using the Wizard to Establish a Connection Entering the Wireless LAN Encryption Key Next, enter the encryption key of the wireless LAN terminal. For details on the encryption key, refer to the device’s instruction manual. Note that the screens displayed in steps 1 to 3 below vary depending on the authentication and encryption of the wireless LAN terminal. 1 The [Key index] screen is displayed only if WEP encryption is used by the wireless LAN terminal.
WPS Connections (PBC Mode) This is a connection mode when using a wireless LAN terminal compatible with Wi-Fi Protected Setup (WPS). Pushbutton Connection mode (PBC mode) makes it easy to establish a connection between the camera and the wireless LAN terminal by pressing the WPS button on the wireless LAN terminal. Note that if multiple wireless LAN terminals are active in your area, it may be harder to establish a connection. In this case, try using [WPS (PIN mode)] to establish a connection.
WPS Connections (PIN Mode) This is a connection mode when using a wireless LAN terminal compatible with Wi-Fi Protected Setup (WPS). In PIN code connection mode (PIN mode), an 8-digit identification number specified on the camera is set on the wireless LAN terminal to establish a connection. Even if there are multiple wireless LAN terminals active in your area, this is a relatively reliable method of establishing a connection using a shared identification number.
Configuring Network Settings Turn the <5> dial to select how to configure the network settings, and then press <0>. Select [OK] and press <0> to go to the next screen. [Auto setting] Settings otherwise configured with [Manual setting] can be configured automatically. However, the IP address and similar settings must be automatically assigned and configured in environments using DHCP servers or wireless LAN terminals or routers supporting DHCP server functions.
Configuring Network Settings Completing Settings for the Communication Method The following instructions are for settings screens that vary depending on the communication method (FTP Transfer, EOS Utility, or WFT Server), as shown below. Read the page that introduces the selected communication method. FTP trans. Chapter 2 (p.29) EOSUtility Chapter 3 (p.43) C Y P O Windows Vista Users Before performing the operations from page 43, perform the operations below.
Configuring Network Settings Virtual Keyboard Operation The virtual keyboard is displayed during entry of the encryption key, server name, and other information. Switching to other input areas To switch between input areas, press the button. Moving the cursor To move the cursor, turn the <5> dial. You can also move the cursor using <9>. Entering text In the bottom input area, turn the <5> dial to move the cursor and press <0> to enter text. You can also move the cursor using <9>.
C 28 Y P O
Transferring Images to an FTP Server Y P O With FTP transfer, you can automatically transfer each image to the FTP server as you shoot or transfer a set of shots together.
Configuring FTP Communication Settings These instructions are continued from Chapter 1. 1 Turn the <5> dial to select [Address setting], and then press <0>. 2 If you have set the DNS server setting to [Disable], the screen at left is displayed. Press <0> to select the input position, and then turn the <5> dial to enter the IP address of the FTP server. If you have set the DNS server IP address setting to [Auto assign] or [Manual setting], the screen at left is displayed.
Configuring FTP Communication Settings 6 Complete the [Login method] settings. Turn the <5> dial to select [OK], and then press <0> to go to the next screen. 7 Complete the [Target folder] settings. Select [Root folder] to have images saved in the root folder as specified in FTP server settings. (p.41) Select [Select folder] to specify a subfolder in the root folder. If no folder exists, a folder will be created automatically.
Automatic Image Transfer After Each Shot An image can be automatically transferred to the FTP server immediately after shooting. You can also continue shooting even while images are being transferred. Before shooting, be sure to insert a memory card in the camera or connect external media (p.71). If you shoot without recording images, they cannot be transferred. Note that automatic transfer of movie is not supported. Transfer the movie after shooting, as described on pages 35-39.
Automatic Image Transfer After Each Shot Selecting Particular Sizes or Types of Images to Transfer In automatic transfer during shooting, you can choose which images to transfer if different sizes of images are recorded to the memory card and external media, or during RAW+JPEG shooting. 1 In [WFT settings], select [Set up]. 2 Select [Transfer type/size]. 3 Select the size and type of images to transfer.
Transferring Images Individually Simply select an image and press <0> to transfer it. You can also add a caption before transferring images. You can also continue shooting even while images are being transferred. Transferring the Current Image 1 In [WFT settings], select [Set up]. 2 Select [Transfer with SET]. 3 Select the image. Select [Enable]. C 34 Y P O On the camera body, press the button. Select the image to transfer, and then press <0> to transfer the image.
Transferring Images Individually Adding a Caption Before Transfer You can add a registered caption to each image before transfer. This is effective if you want to inform the recipient the printing quantity, for example. The caption is also added to images stored on the camera. For instructions on creating and registering captions, refer to page 110. You can check for captions added to images by examining the Exif information, in the user comments. 1 2 Take the picture.
Batch Transfer After shooting, you can select multiple images as desired and transfer them all at once. You can also transfer unsent images or images that could not be sent previously. If both a CF card and SD card are used at the same time, or if external media is connected, images are transferred from the source specified on the menu [5] tab, in [Record func+media/folder sel.] [Record/play]. You can also continue shooting even while images are being transferred.
Batch Transfer 4 Transfer the images. Select [Transfer]. Select [OK] on the confirmation screen displayed next. X A transfer progress screen is displayed. During image transfer, the lamp blinks. Menu Operation During Image Transfer You can use the menu even during image transfer. However, to prevent transfer problems, some menu items are unavailable during transfer, including [WFT settings], [Protect images], [Erase images], [Format], and [Record func+media/folder sel.].
Batch Transfer Batch Transfer of Images in a Folder 1 In [WFT settings], select [Image sel./ transfer]. 2 Select [Sel.n]. 3 Select [Folder images not transfer’d]. Y P O To transfer images that could not previously be transferred, select [Folder images failed transf.]. C 4 Select a folder. 5 Transfer the images. Select [Transfer]. Select [OK] on the confirmation screen displayed next. X A transfer progress screen is displayed. During image transfer, the lamp blinks.
Batch Transfer Batch Transfer of Images on memory Cards 1 In [WFT settings], select [Image sel./ transfer]. 2 Select [All image]. 3 Select [Card images not transferred]. C 4 Y P O To transfer images that could not previously be transferred, select [Card images failed transfer]. Transfer the images. Select [Transfer]. Select [OK] on the confirmation screen displayed next. X A transfer progress screen is displayed. During image transfer, the lamp blinks. Selecting [Clear card’s transf.
Checking Image Transfer History Checking the Transfer History of Individual Images To check the transfer history, in [Image sel./transfer], select [Sel.Image]. Image not selected for transfer (no icon) Image selected for transfer Image could not be transferred Y P O Image transferred C Checking the Transfer History of Folders or Memory Cards On the [Image sel.
Viewing Transferred Images Images transferred to the FTP server are stored in the following folder as specified in the FTP server settings. Windows Under the default settings of the FTP server, images are stored in [C drive] [Inetpub] folder [ftproot] folder, or in a subfolder of this folder. If the root folder of the transfer destination has been changed in the FTP server settings, ask the FTP server administrator where images are transferred. Macintosh Open the [Macintosh HD] [Users] folder.
C 42 Y P O
Remote Capture Using EOS Utility Y P O You can use EOS Utility to shoot remotely over a wireless or wired LAN. In addition to remote capture, all camera operations in EOS Utility are supported because a wireless or wired network is used with this option instead of the USB cable.
Configuring EOS Utility Communication Settings These instructions are continued from Chapter 1. With EOS Utility, you can use the included WFT Pairing Software to establish a connection between the transmitter and a computer. WFT Pairing Software is installed automatically during easy installation of the software provided with the camera. If it is not installed, install it on the computer for communication with the transmitter before this procedure.
Configuring EOS Utility Communication Settings 3 Double-click the pairing software icon. X Detected cameras are listed. Cameras that have already been connected are not included in the list. Click [Connect]. If multiple cameras are displayed, identify the camera to connect to by its [MAC address] or [IP address]. You can check the [MAC address] and [IP address] by accessing [Confirm settings] in the menu (p.66).
Configuring EOS Utility Communication Settings There is no need to complete pairing again if you will continue using a particular camera, transmitter, and computer together after pairing without changing the settings. Before your next PTP session, simply turn on the camera to which the transmitter is attached and start the pairing software. The connection between the camera and computer will be established automatically. You can add the pairing software to the software launched at startup of your computer.
Using EOS Utility For EOS Utility instructions, refer to the Software Instruction Manual (PDF). You can take full advantage of EOS Utility via the transmitter just as via a USB connection, without restrictions. C Y P O In Remote Live View shooting, the rate of image transmission is slower than via USB. The motion of moving subjects cannot be displayed smoothly.
C 48 Y P O
Remote Capture Using WFT Server Y P O Using a web browser, you can view images on a memory card in the camera and download them to a computer. Additionally, you can shoot remotely over a wireless or wired LAN. Note that bulb and movie shooting are not supported.
Configuring WFT Server Communication Settings These instructions are continued from Chapter 1. Press <0>. Turn the <5> dial to select the set number, and then press <0>. Press <0> again. After the connection wizard is closed, the display reverts to the menu screen. X The lamp on the transmitter is lit in green. Settings information is stored on the camera. It is not stored on the transmitter. Setting up an Account Y P O Enter a logon name and password for accessing the camera from a computer.
Configuring WFT Server Communication Settings 3 Turn the <5> dial to select [WFT account], and then press <0>. When changing the port number, turn the <5> dial to select [Port number] and press <0>. Note that there is normally no need to change the port number (80). 4 Select a user number. With WFT Server, you can connect the camera to up to three computers. Here, select a user number to prevent conflicts when users at other computers are connected to the transmitter simultaneously.
Displaying WFT Server In the web browser, display WFT Server, a screen for transmitter operations. Make sure you have already established a connection between the camera and computer. 1 2 3 Start the web browser. First, start Internet Explorer or another web browser. Enter the URL. In the address field, enter the IP address assigned to the camera. Press the key. Complete the [Login name] and [Password] settings.
Viewing Images Browse images on the camera’s memory card as follows. 1 Click [Viewer]. 2 Select the memory card. X The image viewing screen is displayed. Click [CF], [SD], or the external media. Click the [DCIM] folder and select the folder containing the images. C 3 Y P O Select an image. To view another image, click the < > buttons or jump to other pages.
Viewing Images 4 Download images to the computer. Click a thumbnail. X The image is displayed at a larger size. To download the image to your computer, click < >. Click [Return] to return to the image viewing screen. Y P O Although actual RAW images and movies are not displayed here, they can be downloaded to the computer the same way as JPEGs.
Remote Capture [Camera control] First, prepare the camera for Live View shooting. Note that remote capture of movies is not supported. For web browsers that do not support JavaScript, refer to page 59, “Remote Capture.” 1 Click [Camera control]. X The advanced capture screen is displayed.
Remote Capture [Camera control] 2 Set the lens focus mode switch to . 3 Display Live View image. 4 Manually adjust the focus. ⑯ Under these conditions, click the release button (⑤). When you let go of the mouse button, the camera autofocuses and shoots. (See step 5.) With One-Shot AF, the camera does not shoot unless focus is achieved. Try following the next steps to display Live View image and shoot after manually focusing. Click the Live View shooting button (⑯).
Remote Capture [Camera control] 5 Configure the shooting settings. 6 Take the picture. Click setting items (such as quality) to view the setting details, which you can configure. Complete the settings as needed. Click the release button (⑤). When you let go of the mouse button, the camera shoots. X The captured image is now displayed. Captured images are stored on the memory card. To download images to your computer, refer to page 53, and use the [Viewer] function.
Remote Capture [Simple control] First, prepare the camera for Live View shooting. Note that remote capture of movies is not supported. For web browsers that do not support JavaScript, refer to page 59, “Remote Capture.” 1 Click [Simple control]. X The basic capture screen is displayed, and Live View image is displayed.
Remote Capture The following instructions are for remote capture with web browsers that do not support JavaScript. First, prepare the camera for Live View shooting. Note that remote capture of movies is not supported. Screen Release button 1 Click [Capture]. 2 Take the picture. X The capture screen is displayed. Live View image is not displayed. Set the lens focus mode switch to . Adjust the focus on the camera. Click the release button. When you let go of the mouse button, the camera shoots.
C 60 Y P O
Linked Shooting Y P O With linked shooting, up to 10 slave cameras can be linked in a wireless network (via IEEE 802.11g in ad hoc mode) to the master camera on which you will release the shutter. Any cameras compatible with linked shooting, when they have WFT series transmitters attached, can be used as slave cameras, regardless of model. C Note that there will be a slight delay after you release the master camera shutter before the slave cameras shoot. Movie shooting is not supported.
Setting Up Linked Shooting First, establish a connection from the slave cameras to the master camera. Because linked shooting utilizes a wireless connection via IEEE 802.11g in ad hoc mode, it is not available over wired LANs. 1 Display the transmitter menu. 2 Select [Connection wizard]. 3 Select [LinkedShot]. On the camera, press the <7> button. On the [7] tab, select [WFT settings] and press <0>. [WFT settings] is added to the tab after you attach the transmitter.
Setting Up Linked Shooting 5 Set up the master camera. 6 At this point, switch to setting up the slave cameras. 7 Check the number of slave cameras. Configure the settings on the master camera following steps 1-3 on the previous page, and then select [Master]. X The following screen is displayed. On the slave cameras, select [OK]. Y P O X On the master camera LCD monitor, the number of slave cameras detected is displayed. C 8 Establish the connection.
Arranging the Slave Cameras Slave camera Slave camera Slave camera Slave camera Y P O Master camera Arrange the slave cameras in clear view of the master camera, without objects between them. You can arrange master camera in an overall circumference of up to approximately 100 m / 328 ft.
Managing Settings Information C Y P O 65
Checking Settings Check the network settings as follows. 1 In [WFT settings], select [Set up]. 2 Select [Confirm settings]. X The settings are displayed.
Changing Settings Settings originally completed using the connection wizard can be changed as follows. You can also change IP security settings (IPsec) not completed using the connection wizard, as well as other settings, such as the setting that determines what happens if an image of the same file name as an existing file is sent to the FTP server. (p.68) 1 In [WFT settings], select [Set up]. 2 Select [LAN settings]. 3 Select the settings number. 4 Select [Change]. 5 Select the item to change.
Changing Settings IP Security (IPsec) Configured in [TCP/IP] [Security]. IPsec is a set of standards for encrypted communication over the Internet. It provides effective security for both wireless and wired LANs. To use this function, you must enable IPsec in the network settings of your computer. When IPsec is employed, only transport mode is supported, and DES encryption and SHA1 authentication are used.
Saving and Loading Settings Network settings can be saved on a memory card for use with other cameras. Saving Settings 1 In [WFT settings], select [Set up]. 2 Select [LAN settings]. 3 Select the settings number. Y P O Here, select the settings number that identifies the LAN settings. C 4 Select [Change]. 5 Select [Save settings].
Saving and Loading Settings 6 Select [Save]. X The settings are now saved as a file on the memory card. The settings are saved as a file (WFTNPF**.NIF) in the area of the memory card shown when the card is opened (in the root directory). The file name is determined automatically by the camera: WFTNPF, followed by a number (01 to 99) and the extension NIF. You can rename the file as desired by selecting [Change file name]. Loading Settings Load settings files stored on a memory card as follows.
Using External Media Y P O Commercially available external media, connected via USB, can be used the same way as CF and SD cards. You can also back up images from CF and SD cards onto external media. C Note that external media must meet the following requirements. Use media conforming to the USB Mass Storage Class Specification. If an external hard disk drive is used, use a self-powered drive. Buspowered drives do not work in some situations.
Connecting External Media Before connecting external media to the transmitter, switch the camera’s power switch to . Also turn off external media that has its own power supply. When connecting external media, be sure to use the USB cable provided with the camera. The transmitter USB port is not hot-pluggable. USB cables cannot be connected or disconnected at any time. Follow the instructions in this section when connecting or disconnecting USB cables. 1 Plug the external media into the USB port.
Connecting External Media 5 Select [OK]. Camera operations such as shooting, menu display, or image playback are not possible until the connection is established. When the transmitter is connected to the external media, the transmitter’s lamp is lit in green and a message is displayed indicating that a connection has been established. When the confirmation message is displayed, select [OK]. X At this point, the menu option [Disconnect] becomes available.
Connecting External Media Unplugging External Media from the USB Port Before unplugging external media from the USB port, always select [Disconnect] as shown in step 5. Follow the instructions displayed to terminate the connection. The connection will not be terminated if you simply turn off the camera and external media. If you unplug external media while the connection is still active, plug the external media into the USB port again and follow the preceding steps to terminate the connection.
Choosing Recording Media When Shooting Images can be stored on external media connected via USB just as on CF and SD cards. You can also configure [Record func.], [Record/play], and [Folder] settings (described below) to use the external media. For details, refer to the Camera Instruction Manual (page 56). When recording movies to a hard disk, use a hard disk with fast write speeds. On the [5] tab, select [Record func+media/folder sel.].
Choosing Recording Media When Shooting [Record/play] Setting When you select external media in [Record/play], the [Select location for DCIM folder] screen is displayed. The DCIM folder contains the EOS1D folder, where images are stored. To create the DCIM folder in the first folder displayed when the external media is opened (that is, the root directory), select the default setting of [/]. To create another parent folder for the DCIM folder, select [Create folder].
Copying Images Images can be copied to external media connected via USB just as to CF and SD cards. 1 On the [5] tab, select [Record func+media/folder sel.]. 2 Select the source media in [Record/ play]. 3 On the [3] tab, select [Image copy]. X The icon for external media is displayed next to icons for the CF and SD cards. After selection, press the <7> button to return to the menu screen. C Y P O For subsequent instructions, refer to the Camera Instruction Manual (page 176).
Backing Up on External Media Images stored on CF or SD cards can be backed up on external media. Initially, captured images are stored in the DCIM folder on CF or SD cards. Selecting [External media backup] backs up this DCIM folder to external media. 1 On the [3] tab, select [External media backup]. 2 Check the free space on the media. 3 Select the method of backup. Make sure more space is available on the external media than the amount used on the memory card.
Backing Up on External Media \\\ Quick Backup A simple method of backup is available, as follows. 1 Select [Quick backup]. 2 Select the source memory card. 3 Select [Start]. C 4 Y P O Select [OK]. X The backup process now begins. When the message indicating completion is displayed, select [OK].
Backing Up on External Media Where the DCIM Folder is Stored The DCIM folder is stored in a directory indicated by a file path such as [u/09103102/]. The target folder name comprises the current date (last two digits of the year, in addition to the month and day) and numbers representing the order the folder was created, in a range of 01 to 99. In the example shown at left, the folder displayed when the external media is opened (that is, the root directory) is named 09103102.
Backing Up on External Media 4 Select [Create folder]. 5 Enter the [Folder name]. 6 Select [Start]. 7 Select [OK]. Always use 8 characters for the folder name. For instructions on entering the folder name, refer to “Virtual Keyboard Operation” (p.27). C Y P O X The backup process now begins. When the message indicating completion is displayed, select [OK].
Backing Up on External Media External Media Case The provided external media case can hold portable hard disks up to 120 x 75 x 15 mm/ 4.72 x 2.95 x 0.59 in.
Using GPS Devices Y P O Commercially available GPS devices connected via USB can obtain information including the latitude, longitude, altitude, and date and time of shooting and add it to images. The additional information can be checked on the camera as well as by using GPS-compatible mapping software. C The transmitter can be used with Garmin GPSMAP or eTrex series or Magellan eXplorist series GPS devices that produce data in the format NMEA 0183 Ver. 3.0.
Connecting GPS Devices with a USB Cable Turn off the GPS device and camera before connecting them. When connecting GPS devices, be sure to use the USB cable provided with the camera. The transmitter USB port is not hot-pluggable. USB cables cannot be connected or disconnected at any time. Follow the instructions in this section when connecting or disconnecting USB cables. 1 Plug the GPS device into the USB port. 2 In [WFT settings], select [USB device connec.]. 3 Select [GPS]. 4 Select [Connect].
Connecting GPS Devices with a USB Cable 5 Select [OK]. After selecting [OK], turn the GPS device on. It may take a few minutes to establish a connection with the GPS device. Camera operations such as shooting, menu display, or image playback are not possible until the connection is established. When the transmitter is connected to the GPS device, the transmitter’s lamp is lit in green and a message is displayed indicating that a connection has been established.
Connecting GPS Devices with a USB Cable Unplugging GPS Devices from the USB Port Before unplugging GPS devices from the USB port, always select [Disconnect] as shown in step 5. Follow the instructions displayed to terminate the connection. The connection will not be terminated if you simply turn off the camera and GPS device. If you unplug GPS device while the connection is still active, plug the GPS device into the USB port again and follow the preceding steps to terminate the connection.
Connecting GPS Devices via Bluetooth By attaching the Canon Bluetooth Unit BU-30 to the USB port, you can connect Bluetooth® GPS devices wirelessly. (Bluetooth® devices other than GPS devices cannot be connected). When using non-Canon Bluetooth units, confirm normal operation before use. Turn off the GPS device and camera before attaching the Bluetooth unit to the transmitter. The transmitter’s USB port is not hot-pluggable. Bluetooth units cannot be connected or disconnected indiscriminately.
Connecting GPS Devices via Bluetooth 5 Select [OK]. After the Bluetooth unit is attached to the transmitter, the transmitter’s lamp blinks in green and a message is displayed indicating that a connection has been established. When the confirmation message is displayed, select [OK]. X At this point, the menu option [Disconnect] becomes available. Select this option before detaching the GPS device. 6 Y P O Establish a wireless connection between the GPS device and Bluetooth unit.
Connecting GPS Devices via Bluetooth 8 When the confirmation message is displayed, select [OK]. 9 Take the picture. The GPS connection status changes to [Connecting]. Pressing <0> under these conditions will enable you to disconnect the GPS device. Make sure the transmitter’s lamp is lit in green before shooting. If the lamp is not lit in green when you shoot, the correct GPS data will not be added to images. Y P O Check the GPS data. 10 C View an image.
Connecting GPS Devices via Bluetooth Detaching Bluetooth units from the USB port Before detaching Bluetooth units from the USB port, always select [Disconnect] as shown in step 5. Follow the instructions displayed to terminate the connection. The connection with the Bluetooth unit will not be terminated if you simply turn off the camera. If you detach a Bluetooth unit while the connection is still active, attach the Bluetooth unit again and follow the preceding steps to terminate the connection.
Troubleshooting C Y P O 91
Responding to Error Messages If transmitter errors are displayed on the camera LCD monitor, refer to the examples of corrective actions in this section to eliminate the cause of the error. The error details can also be checked on the [7] tab [WFT settings] [Error description]. Click the error number in the following chart to jump to the corresponding page. 11 (p.93) 12 (p.93) 21 (p.93) 22 (p.94) 23 (p.94) 24 (p.95) 31 (p.97) 32 (p.97) 33 (p.97) 34 (p.97) 41 (p.98) 42 (p.99) 43 (p.99) 44 (p.
Responding to Error Messages 11: Connection target not found Is the pairing software running? X Start the pairing software and follow the instructions to re-establish the connection. (p.44) Are the transmitter and wireless LAN terminal configured with the same encryption key for authentication? X This error occurs if the encryption keys do not match when the authentication method for encryption is [Open system]. The setting is case-sensitive, so check upper- and lower-case characters.
Responding to Error Messages 22: No response from DNS server What to check on the transmitter On the transmitter, the DNS address setting is [Auto assign] or [Manual setting]. Does the error occur under these settings? X If no DNS server is used, set the transmitter’s DNS address setting to [Disable]. (p.25) On the transmitter, does the DNS server’s IP address setting match the server’s actual address? X Configure the IP address on the transmitter to match the actual DNS server address. (p.
Responding to Error Messages 24: No response from proxy server What to check on the transmitter The transmitter’s proxy server setting is [Enable]. Does the error occur under this setting? X If no proxy server is used, set the transmitter’s proxy server setting to [Disable]. (p.30) Do the transmitter’s [Address setting] and [Port No.] settings match those of the proxy server? X Configure the transmitter’s proxy server address and port number to match those of the proxy server. (p.
Responding to Error Messages 25: Another terminal has set the same IP address Is another device on the transmitter network using the same IP address as the transmitter? X This error occurs if the transmitter is connected to a network where another device subsequently connects with the same IP address. Change the transmitter’s IP address to avoid using the same address as another device on the network. Otherwise, change the IP address of the device that has a duplicate address.
Responding to Error Messages 31: USB connection disconnected Has the USB cable been disconnected? X After connecting the USB cable, in [WFT settings], select [USB device connec.] and reconnect the device. Is the USB device on? X Turn the USB device on. Next, also in [WFT settings], select [USB device connec.] and reconnect the device.
Responding to Error Messages 41: Cannot connect to FTP server What to check on the transmitter On the transmitter, does the FTP server’s IP address setting match the server’s actual address? X Configure the IP address on the transmitter to match the actual FTP server address. (p.30) Are the transmitter and wireless LAN terminal configured with the same encryption key for authentication? X This error occurs if the encryption keys do not match when the authentication method for encryption is [Open system].
Responding to Error Messages Are you connecting to the FTP server via a broadband router? X Some broadband routers use a firewall to restrict access to the FTP server. Change the firewall settings to allow access to the FTP server. X You may be able to access the FTP server by setting [Passive mode] to [Enable] on the transmitter. (p.
Responding to Error Messages 45: Cannot login to FTP server. Error code received from server. What to check on the transmitter On the transmitter, is the [Login name] entered correctly? X Check the logon name for accessing the FTP server. The setting is case-sensitive, so check upper- and lower-case characters. Make sure the correct logon name is entered on the transmitter. (p.
Responding to Error Messages 47: Image file transfer completion not confirmed by FTP server This error occurs if, for some reason, the transmitter fails to receive confirmation from the FTP server that image file transfer is complete. X Restart the FTP server and camera and send the images again. 51: Connection with Bluetooth unit lost Is the Bluetooth unit too far from the GPS device? X Bring the GPS device closer to the Bluetooth unit.
Responding to Error Messages 61: Same SSID wireless LAN terminal not found Are any obstacles blocking the line of sight between the transmitter and the antenna of the wireless LAN terminal? X Move the antenna to a position clearly visible from the point of view of the transmitter. (p.106) What to check on the transmitter On the transmitter, does the SSID setting match that of the wireless LAN terminal? X Check the SSID on the wireless LAN terminal, and configure the same SSID on the transmitter. (p.
Responding to Error Messages 63: Wireless LAN authentication failed Are the transmitter and wireless LAN terminal configured for the same authentication method? X The transmitter supports these authentication methods: [Open system], [Shared key], [WPA-PSK], and [WPA2-PSK]. (p.21) X When using an AirPort for communication in infrastructure mode, [Open system] is not supported. Configure a [Shared key] on the transmitter. (p.
Responding to Error Messages 66: Incorrect wireless LAN encryption key Are the transmitter and wireless LAN terminal configured with the same encryption key for authentication? X The setting is case-sensitive, so check upper- and lower-case characters. Make sure the correct encryption key for authentication is entered on the transmitter and wireless LAN terminal. (p.22) Note that if the authentication method is [Open system], an Error 41 (“Cannot connect to FTP server”) is displayed.
Responding to Error Messages 71: Cannot connect to slave cameras Are you following the correct procedure to establish the connection with slave cameras? X Operate slave cameras by following the correct instructions (p.62, 63). Are the slave cameras too far from the master camera? X Bring the slave cameras closer to the master camera.
Wireless LAN Notes When using the transmitter with a wireless LAN, try the following corrective actions if the transmission rate drops, the connection is lost, or other problems occur. Wireless LAN Terminal Installation and Antenna Position When using the transmitter indoors, install the wireless LAN terminal in the same room where you are shooting. Install the wireless LAN terminal higher than the transmitter. Install the device where people or objects do not come between it and the camera.
Checking Network Settings Windows Click the Windows [Start] button [All Programs] [Accessories] [Command Prompt]. Type ipconfig/all and press the key. The IP address assigned to the computer is displayed, as well as the subnet mask, gateway, and DNS server information. To avoid using the same IP address for the computer and other devices on the network when configuring the IP address assigned to the camera (page 25), change the rightmost numbers here.
C 108 Y P O
Reference C Y P O 109
Creating and Registering Captions Follow these steps to create captions and register them on the camera, as introduced in “Adding a Caption Before Transfer” (p.35). When creating and registering captions, use a computer on which EOS Utility is installed. Before you begin, attach the transmitter to the camera and use the USB cable provided with the camera to connect the camera to the computer.
Specifications Type Type: Image transfer accessory that can be used in wireless LANs and over Ethernet in wired LANs (IPsec-compatible). Can be connected via USB to external media, GPS devices, and Bluetooth units. Wireless LAN Standards compliance: Transmission method: Transmission range: Transmission frequency: (central frequency) Connection method: Security: Wired LAN Standards compliance: IEEE 802.11a (WFT-E2 IIA/B/C) and ARIB STD-T71 IEEE 802.11b and ARIB STD-T66 IEEE 802.
Specifications Image Capture Capacity LAN Wireless LAN Wired LAN At Normal Temperature (23°C / 73°F) 1100 1200 Approx. number of images At Low Temperature (0°C / 32°F) 900 900 * Using a fully charged LP-E4 * Testing based on Camera & Imaging Products Association (CIPA) standards * Fewer images can be captured when transferring images over wireless LAN. * Fewer images can be captured when using bus-powered external media or GPS devices. Dimensions and Weight Dimensions (W x H x D): Weight: 26.
C Y P O 113
C 114 Y P O
C Y P O 115
Statement on EC directive Canon Inc. tímto prohlašuje, že tento CH9-1161 je ve shodČ se základními požadavky a dalšími pĜíslušnými ustanoveními smČrnice 1999/5/ES. Undertegnede Canon Inc. erklærer herved, at følgende udstyr CH9-1161 overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Hiermit erklärt Canon Inc., dass sich das Gerät CH9-1161 in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
FCC / IC Notice Model DS585802/DS585804 (including WLAN Module Model CH9-1161) This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.
Index Infrastructure......................................... 8, 21 IP address........................................... 25, 30 IPsec ......................................................... 68 Wireless and Wired LAN Functions J A JPEG......................................................... 33 Account ..................................................... 50 Ad hoc ................................................... 8, 21 Area of use .................................................. 8 Authentication.
Index S Select folder .............................................. 31 Settings information................................... 65 Shared key ................................................ 21 Simple control............................................ 58 Slave camera ............................................ 62 SSID .......................................................... 21 Stealth functions.................................. 23, 24 Storage......................................................
CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan U.S.A. CANON U.S.A. INC. One Canon Plaza, Lake Success, NY 11042-1198, U.S.A. For all inquires concerning this product, call toll free in the U.S. 1-800-OK-CANON CANADA CANON CANADA INC. HEADQUARTERS 6390 Dixie Road, Mississauga, Ontario L5T 1P7, Canada CANON CANADA INC. MONTREAL BRANCH 5990, Côte-de-Liesse, Montréal Québec H4T 1V7, Canada CANON CANADA INC. CALGARY OFFICE 2828, 16th Street, N.E.