Digital Satellite Receiver CryptoWorks Embedded User's Manual The product image may differ from the actual product.
Notice Thank you for purchasing a HUMAX product. Please read this user manual carefully, to be able to safely install, use and maintain the product at maximum performance. Keep this user manual next to your product for future reference. Throughout the whole manual, Note indicates additional product operation information to make the user aware of possible problems and information of any importance to help the user understand, use and maintain the installation.
Safety Warning ** The product has been manufactured to satisfy international safety standards. Please read the following safety precautions and warnings carefully. ** • • • • • • • • • • • Disconnect the product from the mains before you start any maintenance or installation procedures. Do not overload a wall outlet, extension cord or adapter as this may result in electric fire or shock. The product should not be exposed to liquid of any kind.
Contents 1. Before Using the Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 7. Parental Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1 Parental Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.2 Modify PIN code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1. Before Using the Product 1. Before Using the Product This chapter provides detailed instructions on the product and its accessories. 1.1 Package Contents When you unpack your package contents, make sure you have all the necessary items shown in the figure below. If any of the items are missing or damaged, please contact your local product distributor for replacement.
1. Before Using the Product 1.2 Front Panel ** ** 1. STANDBY Button Switches between operation and standby modes. ** 5. DIGITURK CH LED Amber light is emitted when viewing DIGITURK channel. ** ** 2. MODE Button Switches between DIGITURK and OTHER modes. ** ** 6. STANDBY LED Red light is emitted when the product is in standby mode. ** ** 3. CH-/CH+ Button Moves the TV/radio channel up/down. ** ** 4. MAIL LED Green light is emitted when the mail was received. ** ** 7.
1.3 Rear Panel ** ** 1. LNB IN 7. AUDIO L/R ** ** Connects to a satellite antenna cable. Connects to the TV or VCR and outputs audio signals. ** 2. LNB OUT ** 8. RF OUT ** ** Connects to another digital Set-Top Box. Connects the RF output jack of the product and the RF input jack on the TV with the RF cable. The default UHF channel is 36. ** 3. RS-232C ** Connects to your PC to update software. ** 4. TV SCART ** Connects a TV SCART cable. ** 5. VCR SCART ** Connects a VCR SCART cable.
1. Before Using the Product 1.4 Conditional Access Although some TV and radio channels are free to air, most TV and radio/music channels are available on a subscription basis and can only be enjoyed via Conditional Access component. ** 1. Inserting Smartcard ** A Smartcard looks similar to a credit card and entitles you to view and listen to all the channels you choose to subscribe to. The Smartcard slot on the product can be used for CryptoWorks Smartcard only. ** 1.
2. Inserting CI (Common Interface) Module ** Your product is equipped with a slot for Common Interface (CI). ** 1. Open the right-hand flap on the front panel of the product. 2. Insert the Smartcard into the CI module, and the CI module into the slot.
1. Before Using the Product 1.5 Remote Control 1. AV ** Selects the input source between TV and the product. ** 2. MODE ** Switches between DIGITURK and OTHER modes. ** 3. NUMERIC BUTTONS ** Enter a TV/radio channel number. ** 4. GUIDE (EPG) ** Displays the programme guide. ** 5. i (INFORMATION) - WHITE ** Displays the information about the channel and programme. ** 6. ARROW BUTTONS ** Changes channels or moves the cursor up, down, left or right in menu option. ** 7.
9. CH-/CH+ 17. LANGUAGE (SOUNDTRACK) – BLUE ** ** Changes the channel. Displays the a soundtrack list where available. ** 10. PP (Recall) ** 18. TXT (SUBTITLE) – YELLOW ** ** Returns to the previous channel in each mode. Displays the subtitle language list where available. ** 11. FREEZE ** 19. V-/V+ ** Freezes the scene you are watching. Does not cease audio. ** Adjusts the audio volume. 20. MUTE ** ** 12. WIDE Mutes or unmutes the audio temporarily. ** Changes the display format.
2. Setup 2. Setup This chapter describes how to set up the product. Select the most appropriate procedure depending on your requirements. Before you connect the product to any other equipment, you must disconnect all equipments from their power sources. Note: If you encounter any problem when setting up the product, please contact your local product distributor. 2.1 Connecting Antenna/TV/VCR 1. Using SCART Cable ** ** 1. Connect the antenna to the LNB IN of the product. 2.
2. Using RCA Cable ** ** 1. Connect the antenna to the LNB IN of the product. 2. The RCA cable is connected as in the figure above.
2. Setup 3. Using RF Cable ** ** 1. Connect the antenna to the LNB IN of the product. 2. The RF cable is connected as in the figure above. ** Note: The default UHF channel is 36.
2.2 Connecting Audio System ** ** 1. Connect the optical S/PDIF terminal and Dolby Digital decoder to listen to higher quality sound. 2. Connect VIDEO on the product and VIDEO IN on the TV using the RCA cable. 3. Connect AUDIO L/R on the product and AUDIO IN L/R on the audio system using the RCA cable.
2. Setup 2.3 Powering On ** 1. Connect the power cord of the product to a wall outlet. ** ** 2. Press the STANDBY button on the front of the product or on the remote control.
3. Basic Operation 3. Basic Operation 3.1 Installation Wizard When powering on your product for the first time after purchase, the selecting country screen is automatically displayed. Select the required country using the button and press the OK button. If you select "Turkey", the DIGITURK Installation menu will be displayed. And if you select other countries, the Advanced Installation menu will be displayed. Note: For detailed information about searching channels, refer to 5.1.
3. Basic Operation 3.2 Viewing Programme You can change the channel using the CH-/CH+, You can adjust the audio volume using the V-/V+ or or NUMERIC buttons. You can also use the Channel List or Programme Guide. button. ** Banner (Programme Information) The banner is always displayed for a specific period of time whenever you switch channels. You can view the programme information by pressing the i button while watching a programme.
3.3 Subtitle If the current programme provides subtitle information, the subtitle icon will appear on the banner. You can select the language for the subtitle using the TXT (SUBTITLE) button. You can select a default subtitle language in MENU-System Settings-Language Setting-Subtitle Language. ** 3.4 Soundtrack If the current programme is available in multiple audio languages, you can select the language that you wish to listen in using the LANGUAGE (SOUNDTRACK) button.
3. Basic Operation 3.5 Teletext ** When the channel supports teletext, the teletext icon is displayed on the banner. To enter Teletext mode, use the TXT (SUBTITLE) button to display teletext. button and press the To display teletext menu, press the OPTS button in teletext mode. Select your desired teletext function using the OK button. To view the teletext page, use the CH-/CH+, , PP or NUMERIC buttons.
4. Menu Map 4.
4. Menu Map Menu structure varies according to the item and its operation. You can easily navigate the menu using the following instructions: ** 1. Press the OPTS button to display the main menu screen. ** 2. Select the item you want using the button. ** 3. Press the OK button to move from a menu to a sub-menu. ** 4. Press the button to select option values. ** 5. Press the NUMERIC buttons to enter the option values. ** 6. Press the BACK button to return to the parent-menu. ** 7.
5. Installation 5. Installation 5.1 DIGITURK 1. DIGITURK Installation You can automatically search the channel without entering any other information. 2. Change CAS Slot of All DIGITURK Channels You can check the CAS slot currently in use and change the CAS slot of all DIGITURK channels. Select the CAS slot you want using the button and press the OK button.
5. Installation 5.2 Advanced Installation You can search other channels except DIGITURK channel. Enter the PIN code using the NUMERIC buttons. The default PIN code is set to "0000". 1. Antenna Setting You can set antenna and LNB information to search channels using Antenna Setting (MENU-Installation-Advanced Installation-Antenna Setting). ** • • • • • • • • Antenna Alternative: Select antenna alternative which has different combinations of settings for search.
2. Manual Search You can search channels of the selected satellite by transponders using the transponder information. ** • • • • • • • • Antenna Alternative: Select antenna alternative which has different combinations of settings for search. Antenna Alternative 16 is predefined for SMATV. Frequency: Enter transponder frequency. Polarisation: Select the type of polarisation. Symbol Rate: Select or enter transponder symbol rate. FEC: Select FEC (Forward Error Correction).
5. Installation 3. Satellite Setting This menu appears only when you enable Motorised System in Antenna Setting menu and press the OK button while Antenna Alternative in Manual Search menu is selected. ** • Satellite Name: Select a satellite to identify a motor antenna. If the desired satellite name is not listed, then select "other". ** • Movement: In user mode, this is used to fine-tune the position of the motor. In installer mode, this is used to search for the position of the satellite manually.
** To initialise the satellite position saved at Motor Antenna, set DiSEqC Command Mode to "Installer", set Motor Control to "Reset", then press the OK button. You will see a warning message. To continue the procedure, press the OK button. To set the motor position for each satellite manually, select the Satellite Name, set DiSEqC Command Mode to "Installer", and then set Movement to one option among "East", "Stop" or "West". The motor starts moving.
5. Installation 5. Automatic Search If you select the satellite to search channels according to Antenna Setting, you can automatically search the channel without entering any other information. To enter Automatic Search menu, press the OPTS button, then select Installation-Advanced Installation-Automatic Search. ** • Antenna Alternative: Select antenna alternative which has different combinations of settings for search. The Satellite Name is automatically displayed.
5.3 Organise Channels 1. Organise All Channels You can edit TV or radio channels using Organise TV/Radio Channels (MENU-Installation-Organise Channels-Organise TV/Radio Channels-Organise All Channels). You will be prompted to enter the PIN code. The default PIN code is "0000". Before leaving Organise TV/Radio Channels screen, you will be prompted to save the changes. If you would like to save the changes, select OK and press the OK button. ** You can delete, move, lock or unlock, skip and rename channels.
5. Installation 2. Organise Favourite A~B You can add channels to Favourite groups using Organise Favourite TV/Radio Channels (MENU-Installation-Organise Channels-Organise TV/Radio Channels-Organise Favourite A~B). Before leaving Organise Favourite TV/Radio Channels screen, you will be prompted to save the changes. If you would like to save the changes, select OK and press the OK button.
3. Organise Satellites You can delete satellites and transponders. To enter Organise Satellites menu, go to MENU-Installation-Organise Channels-Organise Satellites. The Organise Satellites screen consists of Satellite List on the left side of the screen and Transponder List and Channel List on the right side. You can move the highlighter in order of Satellite List, Transponder List and Channel List using the button. You can move the highlighter in reverse direction using the button.
5. Installation 5.4 Factory Settings You can restore the product to the factory settings using the Factory Settings menu (MENU-Installation-Factory Settings). You will be prompted to enter the PIN code. The default PIN code is "0000". For more information, refer to 5.1.1 DIGITURK Installation. Warning: Please note that once you perform the factory setting, all data except the customised PIN code will be restored to the factory settings.
6. System Settings 6. System Settings The System Settings menu (MENU-System Settings) lets you customise your product according to your perference. 6.1 Language Setting You can set the default language for menu, audio and subtitle. ** 6.2 Time and Date Setting You can set the current time and turn the product on or off automatically. Once you set the Wakeup time and Sleep time, the product is turned on and off everyday. Warning: When setting Wakeup Channel No.
6. System Settings 6.3 A/V Output Setting This menu lets you adjust the audio and video output, set Dolby Digital, match the screen ratio to your TV, select the display format according to the screen ratio, select the TV standard and set the NTSC mode. Note: You can choose the Dolby Digital audio stream whenever possible by selecting "ON" in the Dolby Digital setting. 6.4 UHF Tuning You can select UHF Channels for your TV and adjust fine tuning setting.
6.5 Other Setting You can adjust the transparency level of On-Screen Display (OSD), set the duration of the banner when switching channels, select automatic or manual mode for changing to reserved channel and set the duration of the reminder.
6. System Settings 6.6 System Information The System Information menu (MENU-System Settings-System Information) provides information such as STB status, signal level of channel and software upgrade. Note: • You can also display STB Status by pressing i and OK button. • For more information about software upgrade, refer to 14. Software Upgrade.
7. Parental Control 7. Parental Control The Parental Control menu (MENU-Parental Control) lets you control the access to programmes by programme rating. Note: Enter the PIN code using the NUMERIC buttons. The default PIN code is set to "0000". 7.1 Parental Rating Set Parental Rating by age level. “no block” allows you to watch programmes without any blocking. You can block all programmes regardless of age level. The blocked programmes require the PIN code. ** 7.
8. Channel List 8. Channel List There are five types of channel lists – All, Favourite, Network, Satellite, Alphabet - to find channels you are interested in quickly and easily. All channel lists display all searched TV or radio channels sorted by channel number. Favourite channel list displays favourite channels with three predefined sub-groups and two user defined sub-groups. Network channel list displays channels with several network subgroups.
8.2 Setting Property of Channel You can add the current channel to Favourite group. In addition, you can lock, unlock, skip or delete the current channel while watching a programme. The operation is as follows: 1. Press the OK button while watching a programme. The channel list will appear on the screen. You can also display the channel list using the MENU-Channel List-Simple (or Advanced).
8. Channel List 8.3 Favourite List You can check and edit Favourite list quickly and easily. 1. Press the FAV button to display Favourite list while watching a programme. 2. Press the RED button to display the all channel list. Select the channel you want to add to Favourite list and press the OK button. Press the BLUE button to view the channel you select. To close the all channel list, press the BACK button. 3. Press the GREEN button while displaying Favourite list to switch between Favourite A and B. 4.
9. Utility 9. Utility The product provides various utilities: calendar, biorhythm and games. To use utilities, go to MENU-UTILITY. 1.Calendar You can see the monthly calendar. Press the button to change the year. Press the button to change the month. Press the OK or BACK button to return to the previous menu. 2. Biorhythm You can adjust your birth year and date to see your current biorhythm status. Press the button to move to the next step. Press the button to change a value in the step.
10. Programme Guide 10. Programme Guide The programme guide provides the programme information for all channels, based on date and time. In addition, it provides convenient ways to view programmes in "Now", "Next", "Weekly" or "Quick" mode - to search your desired programme and to watch or reserve it. You can go to the programme guide screen by just pressing the GUIDE button or by using MENU-EPG. To close the guide screen, press the GUIDE or BACK button.
• • • • Press the WHITE button to reserve the selected programme in "Now", "Next", "Weekly" or "Quick" mode. Press the WHITE button to change the reservation mode or to cancel the reservation in Reserved mode. Select a channel using the or CH-/CH+ button. When switching channels using the button, press the OK button to display the selected channel on the right side of the screen. Select a day in "Weekly" mode using the button, and press the OK button.
11. Mail 11. Mail You receive mails sent by broadcasting company. When a new mail arrives, the envelope icon will appear on the screen. Sometimes a new message will be directly displayed on the screen while you are watching a programme. The old mails will be deleted automatically when your mail box overflows. Select a mail using the button, then press the OK button to read the mail. The message will be displayed. If you would like to delete the read mail, select Delete, and press the OK button.
12. Conditional Access 12. Conditional Access You can check the information of Internal or External Smartcard using the MENU-Conditional Access.
13. Common Interface 13. Common Interface You can check the information of CI module using the MENU-Common Interface.
14. Software Upgrade 14. Software Upgrade In order to maintain proper performance of the product, it is essential to have the most up-to-date software. 14.1 OTA (Over the Air) OTA, an abbreviation of Over–the-Air, is a standard for the transmission of software through a broadcast system. OTA is simply an alternative method for downloading software versions.
14. Software Upgrade Updating software is largely divided into two ways, automatic and manual search in MENU-System Settings-System Information-Software Upgrade. Select Automatic Search to search pre-defined DIGITURK TPs for new software automatically. When new software is available to download, the product will be automatically powered off and on. If new software is not found by automatic update, use manual update. For more information about how to set the manual search, refer to 5.2.2 Manual Search.
15. Troubleshooting 15. Troubleshooting Before contacting your local service, please read the following instructions. If the product does not work normally after completing the following troubleshooting, please contact your local product distributor or service centre. ** 1. The LED on the front panel does not light. - Check the main power cable and make sure that it is plugged into a suitable power outlet. ** 2. No picture - Make sure that the product is in operation mode.
15. Troubleshooting 5. Remote control does not operate - To manipulate the equipment with the remote control, its emitting part should directly point towards its receiving part of the product. - Check the battery of the remote control. ** 6. Reservation is unavailable - Check if it is not overlapped with other reservation. - Check if the power is off. ** 7. Watching scrambled channel is not available - Make sure the correct Smartcard is plugged in.
16. Specification 16. Specification ** MPEG Transport Stream A/V Decoding Power Supply Aspect Ratio Video Resolution Audio Mode Input Voltage Type 4:3, 16:9 720 x 576, 720 x 480 Single /Dual mono/ Stereo /Joint stereo Power Consumption Memory Protection Flash Memory Graphics(MPEG) & System Memory EEPROM 2 Mbytes 16 Mbytes 8 Kbytes RF-Modulator Output Channel TV standard Preset Channel CH 21 ~ 69 PAL I/G/B/D/K CH 36 AC 90 ~ 250V, 50/60Hz Switching Mode Power Supply (SMPS) Operation mode: Max.