Owner's Manual

ManualsBrandsCanon ManualsB/W imageRUNNER CopiersCanon imageRUNNER 2000

Set-Up Sheet

Thank you for purchasing the Canon imageCLASS 2300.

To get your machine ready for use, please follow the instructions in this sheet before referring to any other documentation.

Unpack the machine and its components.

Check that you have the following:

●

Machine with cabinet stand

●

Stamp cartridge and tweezers

●

Paper size notice cards (2)

●

Toner cartridge (in carton)

●

Paper size labels (2)

●

Power cord

●

Telephone cable

●

Paper size plates (2)

for the Machine

●

Destination labels for one-touch

speed dialing keys (2)

Summary of content (8 pages)

PAGE 1
Set-Up Sheet for the Machine Thank you for purchasing the Canon imageCLASS 2300. To get your machine ready for use, please follow the instructions in this sheet before referring to any other documentation. Unpack the machine and its components.
PAGE 2
● ● Documentation Set-Up Sheet for the Machine (This Document) Refer to this document first to install and set up your new machine. ● Set-Up Sheet for Networking and Printing* Refer to this document to set up the machine for network and print functions. ● Basic Guide This manual explains the basic operations of all functions of the machine. Keep this guide handy for easy reference. ● Reference Guide This manual covers machine settings, common operations, maintenance, and troubleshooting.
PAGE 3
7 Pull out the left cover and remove the tape on the inside. 2 Remove the clear protective sheet on the LCD display. 3 Lift the feeder and remove the lining material on the platen glass. 4 Remove the shipping tape on the right side and unscrew the metal pin on the underside of the machine. 6 Open the stack bypass and remove the tape holding the auxiliary tray and the tray extension. 5 Keep the metal pin in the pin slot on the black panel behind the front cover.
PAGE 4
Install the toner cartridge. 1 Open the stack bypass. 2 Slide out the left cover of the stack bypass. 3 Remove the toner cartridge from the bag. Keep the bag in a safe place. 4 Hold the cartridge with both hands and slowly shake it sideways 1 and then back and forth 2 to distribute the toner inside the cartridge. 1 2 1 5 Hold the cartridge on a flat stable surface with one hand, and pull out the seal completely with the other hand.
PAGE 5
Load paper. 1 Pull out the paper drawer until it stops. 2 Remove the black wire 1 and shipping tag, and the orange tape 2. 1 2 NOTE ● You can skip steps 3, 6 and 7 if you are loading letter size paper in the portrait orientation (LTR ● Note that some paper sizes have both portrait ( ) and landscape ( 3 Detach the blue end guide by moving it down to the left then pulling up, and attach it again at the mark for the desired paper size. ). ) settings.
PAGE 6
Connect the telephone cable and the power cord. Connect the phone cable 1 and the power cord 2. Turn on the machine’s power by pressing the power switch 3 to ON (“I” side). The power switch is located on the right side of the machine. 3 Power Switch 1 Phone Cable 2 Power Cord Using the operation panel Use the following keys on the operation panel to set up the machine for the fax function as explained on the following pages.
PAGE 7
Set the basic fax settings. NOTE ● ● For details on setting up the machine for the fax function, see Chapter 1,“Before You Use the Fax Functions,” in the Facsimile Guide. For details on how to input characters, see Chapter 2,“Basic Operations,” in the Reference Guide. Setting the Current Date and Time: Additional Functions 1 Press [Additional Functions] ➝ [F3] ( ) or [F4] ( to select <05 TIMER SETTINGS> ➝ press [OK]. ) F3 F4 OK 2 Select <01 DATE/TIME SETTING> ➝ press [OK].
PAGE 8
3 Select <01 TEL LINE SETTINGS> ➝ press [OK]. F3 F4 OK 4 Select <01 USER TEL NO.> ➝ press [OK]. F3 F4 OK @. ABC 1 2 3 GHI JKL MNO DEF 4 5 6 PRS TUV WXY 7 8 9 OPER SYMBOLS 5 Enter your fax number using the numeric keys ➝ press [OK]. 0 OK 6 Press [BACK] ➝ select <02 UNIT NAME> ➝ press [OK]. BACK F3 F4 OK @. ABC 1 2 3 GHI JKL MNO DEF 4 5 6 PRS TUV WXY 7 8 9 OPER SYMBOLS 7 Enter the unit’s name using the numeric keys ➝ press [OK].