DOCUMENT SCANNER INSTRUCTIONS Space E FILM Backup F Count Only New File Scanner Feeding Option A Manual Auto Semi-Auto
FCC REGULATIONS (For 120V models) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Introduction Thank you for purchasing the Canon Document Scanner DR-5060F. The DR-5060F high-speed document scanner has a built-in function for backing data to microfilm. In order to fully understand and effectively use the functions of this scanner, be sure to read this manual before use. Also, after you have read this manual, be sure to store this manual in a safe place.
CONVENTIONS This manual uses the following symbols and indications. Before you start reading this manual, read the following and familiarize yourself with their meanings. WARNING Read carefully to avoid death or serious injury. CAUTION Read carefully to avoid serious injury or damage to the equipment or loss of valuable data. NOTE Read carefully to avoid damage to the equipment. MEMO Memos indicate where you will find useful information in this manual.
Contents Introduction ........................................................................................................................ 1 CONVENTIONS ........................................................................................................... 2 Safety Precautions ............................................................................................................. 5 Daily maintenance ................................................................................................
Chapter 4 Troubleshooting .................................................................... 59 When the Scanner is Not Recognized ............................................................................ 60 Removing Paper Jams ..................................................................................................... 61 Paper Jam in the Paper Eject Section ........................................................................ 61 Paper Jam in the Feed Section ...............................
Safety Precautions Daily maintenance When you are working around the unit, follow these precautions to avoid the hazards of fire and electrical shock: WARNING ■ Never install and operate the unit near flammable substances such as alcohol, benzene, paint thinner, or any other type of volatile solution. ■ Never damage or modify the power cord, place heavy objects on the power cord, or pull or unnecessarily bend the power cord.
CAUTION ■ The scanner weighs about 48 kg (105.8 lb.). To avoid damage to the unit, never place the unit on an unstable or vibrating surface. The unit may tip or fall over, and cause an injury. ■ To avoid overheating and causing a fire, never block the air vents on the rear of the scanner. ■ Keep all liquids, beverages, or any type of liquid, and clips, staples, necklaces or other metal objects away from the unit.
About the Installation Location More than 100 mm (39.0 in.) More than 100 mm (39.0 in.) More than 100 mm (39.0 in.) 771 mm (30.0 in.) (with document tray extension, extension wire closed) 936 mm (36.5 in.) (with document tray extension, extension wire open) More than 740 mm (28.8 in.) For operation, maintenance and ventilation, make sure that there is enough space around the scanner as shown in the illustration above. Do not place the unit in the following places.
About the Power Supply WARNING ■ Be sure to connect to an AC 120V (240 V in Europe) (50/60 Hz) power supply. ■ Ensure that the scanner is connected to an independent power outlet. Do not plug the scanner into an outlet shared with another device. If you use an extension cable, pay attention to the total amperage of the cable. ■ Be sure to connect the ground cable before using the scanner. Also, never connect the ground cable to gas pipes or water pipes.
1 About DR-5060F Chapter 1 About DR-5060F This chapter describes the features of the scanner, what’s in the box, and the names and functions of parts on the scanner and the camera unit. Features of DR-5060F ............................... 10 Packaging: What’s in the Box? ................. 11 Names and Functions of Parts ................. 12 About the Camera Unit .............................
Features of DR-5060F The DR-5060F scanner not only processes large volumes of documents at high speed, but also is provided with a function for backing data to microfilm. Here is a summary of the outstanding features of the DR-5060F. ● High-speed scanning Small documents such as business cards and check-size documents through to A3/(11 x 17 in.)-size documents can be scanned at high speed. The maximum scan speed is 50 sheets per minute (A4/(11.5 x 16.3 in.
Packaging: What’s in the Box? Space E FILM Backup F Count Only New File Scanner Feeding Option A Manual Auto Semi-Auto Setup CD-ROM DR-5060F Removable tray Function key labels DR-5060F Instructions (this manual) Scanning Utility 5060 Instructions ISIS/TWAIN Driver Instructions Document eject support plate Power cord (The power cord varies according to country of purchase.) Software License Agreement Warranty card (For U.S.A.
Names and Functions of Parts This section describes the names and functions of each part. Before you connect the DR-5060F, take a few minutes to familiarize yourself with the main parts. ■ Front view Document eject tray extension/stopper Document eject tray Select the document eject tray extension matched to the size of document you are scanning. (See “Document eject tray extension” P. 34) Operation panel Upper unit open/close button This panel is for setting up scan density and other basic functions.
■ Inside (with upper unit open) 1 About DR-5060F Counter This counter counts the total number of fed document sheets. Space E Feed unit open/close button FILM Backup F Count Only New File Scanner Feeding Option A Manual Auto Semi-Auto Feed unit Intermediate unit Paper feed adjustment lever Slide this lever to adjust paper feed according to the condition of the paper surface. (See “Paper Feed Adjustment” P. 36) ■ Rear view Ground terminal Connect the ground terminal provided to this terminal.
■ Operation panel 1 2 3 4 5 6 (1) Function keys Backup Space/Trailer E FILM F Count Only (6) Clear/Stop key New File Scanner (7) New File key Feeding Option A (2) Remaining film indicator (3) Backup key (4) Space/Trailer key (5) Count Only key Manual Auto (8) Start key Semi-Auto (9) Feeding Option key (10) Brightness key (11) Indicator lamps (12) Counter display (1) Function keys The following functions and settings can be registered to function keys so that they can be called up later
The default setting for this scanner is the Backup mode. Pressing this key turns the lamp in the key OFF and sets the scanner to the Scanner Only mode, and holding this key down for five seconds sets the scanner to the Filmer Only mode. (4) Space/Trailer key This key is enabled when the camera unit is placed on this unit. Pressing this key takes up spaces on the film. Holding this key down for three seconds feeds the trailer film so that the film can be taken out of the camera unit.
(8) Start key When the Start key is lit green, pressing this key starts feeding of originals placed on the document tray. Key functions are disabled when this key is lit red. When this key is blinking green, this indicates that manual thickness adjustment is in progress. To start feeding, end this adjustment. (See “Manual Thickness Adjustment” P. 53) (9) Feeding Option key Select the document feed mode. (See “Selecting the Feeding Option” P.
■ Removable tray ■ Document eject support plate Install this plate when scanning large-size (e.g. A3/11 x 17 in.) thin documents. This plate prevents such documents from becoming caught on the document eject tray. ■ Function key labels Function key labels: Write the name of the function registered to the function key, and affix the label on the function key. Index labels: These labels are for the camera unit. (See “Affixing the Index Label” P.
About the Camera Unit Two camera units are provided for this unit: one with a 1/24 magnification lens and one with a 1/57 magnification lens. The image photographed to film varies according to which of these camera units is used. For details, contact your store of purchase or a Canon service department. ● The ID No. of the camera unit can be set within the range 1 to 15. For details on setting the ID No., contact your store of purchase or a Canon service department.
Chapter 2 2 Preparation Before Use Preparation Before Use This chapter describes the preparations starting with connecting to a computer through to preparations for scanning. System Requirements ............................... 20 Connecting to a Computer ....................... 21 Handling the Camera Unit ........................ 25 Preparing for Paper Feed and Eject ......... 33 Turning the Power ON/OFF .......................
System Requirements To use the DR-5060F, you need the following items in addition to the standard accessories: • Computer • SCSI card • SCSI cable • Application • Camera unit • Microfilm MEMO ● For details on installation of the main unit, see “About the Installation Location” under “Safety Precautions.” ● The driver may not function properly depending on the application you are using. ● Select a computer, operating environment and SCSI card to suit the driver application you are going to use.
Connecting to a Computer Connect the scanner to the computer. CAUTION Before you connect the scanner to the computer, be sure to turn both the scanner and the computer OFF. 2 Connect your computer to the scanner using the SCSI cable. Two half-pitch 50-pin SCSI connectors are located on the rear of the scanner. Insert the SCSI cable from the computer into one of these connectors.
Setting the SCSI ID and Terminator Set the SCSI ID and terminator using the DIP switch on the rear of the scanner. The DIP switch is ON at the up position and OFF at the down position. Default (Terminator: OFF, SCSI ID = 2) SCSI ID switch Terminator ON/OFF switch ■ Setting the SCSI ID Set the SCSI ID by combining the settings of switches SW2 to SW4. Set unique SCSI IDs to any other built-in SCSI devices or SCSI devices connected to the computer.
■ Setting the terminator Set the terminator on the last SCSI device on a daisy chain to ON. Set the terminator DIP switch 1 to ON. In such a connection, be sure to set the terminator on all other SCSI devices to OFF.
Connecting the Power Cord and Ground Cable Connect the power cord and ground cable. Be sure to use only the power cord and ground cable provided with the scanner. ■ Connecting the power cord Connect the power cord to the rear of the scanner, and insert the power plug into the power outlet. WARNING When connecting the power cord, follow these precautions. Failure to do so might cause fire or electrical shock. ● Never grasp the plug when your hands are wet.
Handling the Camera Unit The following describes camera unit handling procedures starting from loading of film in the camera unit through to placing and removing the camera unit from this unit, and removing film. Loading Film Press the release notch to open the camera unit’s cover. Release notch MEMO When you buy the camera unit, the camera unit holds an empty take-up reel inside. If there is no take-up reel inside the camera unit, contact a Canon service department.
3 Place the film on the shaft on the left with the number “2” written on the reel face up. 4 Pass the film along the film path as shown in the figure below. Film 5 Close the left cover taking care not to nip the film. NOTE To prevent the film from being exposed, be sure to close the left cover when the film has been wound out.
6 Draw out the film, and insert the tip of the film into the take-up reel with the number “1” written on the reel face up. 2 Preparation Before Use 7 Place the take-up reel on the shaft. 8 Turn the reel a few times in the direction of the arrow, and make sure that the film is firmly taken up on the reel while taking up any slack in the film at the same time.
9 Close the cover, and make sure that it is locked. Affixing the Index Label Index labels are included among the function key labels that are packaged with the DR-5060F. Affix these index labels at the location specified on the camera unit’s cover.
Loading the Camera Unit in the DR-5060F Load the camera unit loaded with film. 1 Gently insert the camera unit as far as possible into the slot. Space E FILM Backup F Count Only New File Scanner Feeding Option 2 A Manual Auto Semi-Auto Push the camera unit down onto the main unit. Make sure that the camera unit is not riding up from the main unit.
Removing the Camera Unit When document scanning is finished, remove the camera unit from the main unit. 1 Turn the lock lever to the [OPEN] position to unlock the camera unit. Space E FILM Backup F Count Only New File Scanner Feeding Option A Manual Auto Semi-Auto 2 Lift up the front of the camera unit and gently remove it from the slot.
Removing Film Remove photographed film from the camera unit. 1 Hold down the Space/Trailer key on the operation panel for about three seconds to feed the trailer film. The counter display becomes a trailer film display. 1 2 3 4 5 FILM Space/Trailer key Trailer film display F Count Only New File Scanner Feeding Option A Manual Auto Semi-Auto NOTE Do not touch the lock lever with your hand while the trailer film is being fed.
3 Remove the film. 4 Store the film in its case. NOTE ● Develop photographed film as soon as possible. If you leave photographed film for a long time without developing it, the quality of valuable images may be impaired. ● If the density of developed images is unsuitable, adjust the density of the film to be photographed. (See “Function Key Settings” P.52 ) If the image density cannot be adjusted to a suitable density within the adjustment range, contact a Canon service department.
Preparing for Paper Feed and Eject Pull out the document tray extension and document eject tray extension, or attach the document eject support plate or removable tray to accommodate the size and paper quality of the document to be scanned. Also, affix the label for aiding adjustment of the document guide on the document tray.
2 Open the extension wire. ■ Document eject tray extension Open the document eject tray extension to accommodate the size of the document to be scanned. The document eject tray extension extends in two stages. Pull out the stopper to prevent ejected documents from flying out of the document eject tray extension. 1 Pick up the document eject tray extension 1 from the center of the document eject tray. 2 Draw out the document eject tray extension 2 from eject tray extension 1.
■ Document eject support plate Install this plate when scanning large-size documents or documents with a slippery surface. This support plate prevents documents from being caught on the eject section or paper jams from occurring when documents are ejected. 1 Pick up the document eject tray extension 1 from the center of the document eject tray. 2 Install the document eject support plate. Install so that the protrusions on the document eject support plate fit into the holes on the document tray guide.
■ Removable tray Attach this tray when you are scanning small-size documents. This tray prevents documents from flying out of the tray when they are ejected from the scanner. MEMO The removable tray is held in place on the document eject tray extension by magnets. Close the document eject tray extension when the removable tray is in use. 1 Install the removable tray on the center of the eject tray, and adjust the width by the left and right guides.
Turning the Power ON/OFF Follow the procedures below to turn this unit ON and OFF. Turning the Power ON 1 2 To turn this unit ON, press the power switch. MEMO If the error “F01” is displayed when the power is turned ON, the operation mode of this unit is set to the Back up mode or Filmer Only mode without a camera unit placed on this unit. Either place a camera unit loaded with film, or change to the Scanner Only mode.
MEMO If you are using Windows 95/98/Me or Windows 2000, then the first time that you turn on your PC after connecting this scanner to your PC Window’s Plug and Play function will automatically display a screen prompting you to install the scanner driver. (The name of this prompt screen varies among the different versions of Windows.) If “New Hardware Found” is displayed (Windows 95), select “Select from a list of alternative drivers” and click OK. On the next screen, select Other Devices and then click OK.
Chapter 3 Preparing Documents This chapter describes precautions regarding documents that can be handled on this scanner, and document feed and scanning operations. 3 Preparing Documents About Operation Modes ............................ 40 About Documents ..................................... 42 Setting Scan Conditions ...........................
About Operation Modes The DR-5060F is provided with three operation modes: the Backup mode, Scanner Only mode and Filmer Only mode. The Backup mode is for backing up images to microfilm as the document is being scanned. The Scanner Only mode is for using the DR-5060F exclusively as a scanner and not to photograph document images to microfilm. The Filmer Only mode is for using the DR-5060F exclusively as a rotary filmer. You can check and change the operation mode by Backup key.
MEMO ● The images backed up to microfilm sometimes differ from the images transferred to computer depending on the setup conditions. ● When using the 24X lens magnification camera unit, only the top side of the document can be photographed. Photography in the duplex mode is not possible.
About Documents This page explains the types of documents that can be used on the scanner and precautions when loading documents on the document tray. Types of Documents The scanner can accommodate documents of the following width, length and thickness: Width: 55 to 297 mm (2.2 x 11.7 in.) Length: 70 to 432 mm (2.8 x 17.0 in.) Thickness:0.06 to 0.15 mm (0.002 in. to 0.005 in.) (at manual feed: 0.05 to 0.20 mm (0.001 in. to 0.007 in.
MEMO ● Documents comprising pages of differing thickness and size may cause a malfunction during feeding. ● Heavily curled documents or wrinkled or creased paper may cause erroneous double feed detection. ● Documents containing text or pictures within 5 mm (0.1 in.) from its edges or documents with a color background may cause erroneous skew detection or automatic size detection.
Setting Scan Conditions This page explains the functions that can be set on the function keys, Feeding Option key, and brightness key on the operation panel. 1 2 3 4 5 6 Function keys Backup Space/Trailer E FILM F Count Only New File Scanner Feeding Option A Manual Auto Semi-Auto Brightness key Feeding Option key The following functions can be set on the operation panel: ● Setting brightness (Brightness key) Adjust the brightness at which the document is scanned.
Selecting the Feeding Option The procedure for feeding a document varies according to which feed mode is set. You can choose from the following four feed modes using the Feeding Option key. ● Remote In this mode, all of the Feeding Option lamps are out. This mode is enabled in the Backup mode or Scanner Only mode.
■ Remote 1 2 Press the Feeding Option key to turn all lamps out. Load the document face up on the document tray with its top edge inserted first into the scanner. Feeding Option A Manual Auto Semi-Auto 3 Set the document guides for the width of the document you are going to scan. Feeding Option A Manual Auto Semi-Auto 4 5 Instruct start of scanning in the application. The document tray rises, and scanning begins. The document tray is lowered when scanning of all pages in the document ends.
■ Semi-Auto 1 Press the Feeding Option key on the operation panel to light [Semi-Auto]. 2 Load the document face up on the document tray with its top edge inserted first into the scanner. Feeding Option A Manual Auto Semi-Auto Set the paper guides for the width of the document you are going to scan. Feeding Option A Manual Auto Semi-Auto 4 If the scanner is in the Backup mode or Scanner Only mode, instruct start of scanning from the application. The Start key changes color from red to green.
■ Auto 1 Before you press the Feeding Option key on the operation panel to light [Auto] lamp, place one sheet of the document on the document tray and set the paper guide for the width of the document you are going to scan. Feeding Option A Manual Auto Semi-Auto NOTE If Feeding Option is set to [Auto] in the Filmer Only mode, scanning is started once the sensor detects the document placed on the document tray.
5 The document tray automatically rises, and scanning begins. The document tray is lowered when scanning of all pages in the document ends. CAUTION If the document tray does not rise after loading documents on the document tray and you hear a clicking sound, a probable cause is that the document stack weight is heavier than specified even if the load is lower than specified mark on the document tray). Reduce the number of pages to load (below the on the document tray, and try scanning again.
■ Manual Use this mode to scan documents that are not fed well (e.g. paper quality that is more likely to cause double feed). In this mode, you load the document one page at a time with the Feeding Option key set to “Manual. 1 Before you press the Feeding Option key on the operation panel to light [Manual] lamp, place one sheet of the document on the document tray and set the paper guide for the width of the document you are going to scan.
3 If the scanner is in the Backup mode or Scanner Only mode, instruct start of scanning from the application. MEMO Details of scan conditions are set on the application. For details, refer to the separate “ISIS/TWAIN Driver Instructions” or “Scanning Utility 5060 Instructions.” 4 Load one sheet on the document tray up face up with its top edge inserted into the scanner. The document is scanned. 3 Preparing Documents 5 6 Insert the document one page at a time. To end scanning, press the Stop key.
Function Key Settings Twelve function keys are located at the top of the operation panel. The following functions can be registered to these keys. Pressing a specific key calls up the function registered to that key. 1 2 3 4 5 6 Function keys Backup Space/Trailer E FILM F Count Only New File Scanner Feeding Option A Manual Auto Semi-Auto The following settings can be registered to the function keys. Functions are registered to function keys in the application.
■ Manual Thickness Adjustment This scanner is initially set to automatically detect the thickness of paper during scanning. This function, however, may not function properly when scanning extremely thick or thin paper. If this happens, the user must manually adjust the paper thickness so that documents are fed smoothly through the scanner.
■ Fixed Thickness Mode This unit scans while detecting the paper thickness and automatically adjusting the paper thickness setting. However, when scanning extremely thick or thin paper documents, the automatic adjustment functions less effectively, resulting in paper jams. Paper jams in this instance can be prevented by setting the paper thickness to a fixed setting. The paper thickness is set by “Manual Thickness Adjustment” (See “Manual Thickness Adjustment” P. 53).
■ Imprinter When the optional imprinter is installed on the scanner, you can select whether or not to use the imprinter by a function key. To enable use of the imprinter, press the function key to which the imprinter is registered, and scan the document with the key lamp lit. To disable use of the imprinter, scan the document with the key lamp out. ■ Film Density Select the photographic density of the film within the range -3 to +3, and register it to a function key.
Setting in the User Mode The DR-5060F allows you to select which of the following setup items is used as the user mode. Details are available on how to set the user mode. (See “How to Set the User Mode” P. 58) ■ User Mode Setup Items Operation panel buzzer setting Sets whether or not to sound the buzzer when pressing keys on the operation panel. U1-0: Do not sound buzzer during key operation. U1-1: Sound buzzer during key operation.
Count Only mode setting (See “Count Only key lit: Count Only mode” P. 41) Sets use of the imprinter/endorser in the Count Only mode. U8-0: Do not use imprinter/endorser in Count Only mode. (default) U8-1: Use imprinter/endorser in Count Only mode. Endorser stamp mode setting Sets the endorser mode. U9-0: Use the endorser in the check mode. (default) U9-1: Use the endorser in the A4 mode. Space feed setting Sets the space feed amount. Set in 5 mm (0.2 in.) increments within the range 5 mm to 1500 mm (0.2 in.
■ How to Set the User mode Scanner A 1 Hold down [A] key for at least five seconds. The [A] key blinks, and the user mode appears on the counter display. 2 3 4 Select the user mode using the or key. Press the [A] key to select the mode (last number) to be used. Press the Clear/Stop key. This sets the selected mode, and returns the counter display to the counter display.
Chapter 4 Troubleshooting This chapter describes causes of trouble that may occur on the DR-5060F and how to remedy the trouble. When the Scanner is Not Recognized ..... 60 Removing Paper Jams .............................. 61 Paper Feed Trouble .................................... 68 When the Scanned Image is Not Normal ................................................. 70 When an Error Code is Displayed ............
When the Scanner is Not Recognized The following describes possible causes of your computer not recognizing the scanner. Remedy the problem by following the remedy for the respective cause. Cause Remedy The SCSI cable is not correctly connected to the computer. Correctly connect the SCSI cable. Cause Remedy The SCSI card is not correctly recognized. Correctly connect the SCSI card referring to the SCSI card Manual. Also, check that the SCSI card you have mounted is correctly recognized by the OS.
Removing Paper Jams Paper may have jammed if scanning stops midway or “PXX” appears on the counter display. Follow the procedure below to remove jammed paper from inside the DR-5060F. CAUTION ● Be very careful when you remove a paper jam. You may be injured unexpectedly. For example, the paper edges may cut your figures, or the document may be damaged. ● Remove all jammed sheets of paper. Paper scraps left inside the unit may be drawn into the unit again, causing another paper jam or malfunction.
4 Remove the jammed paper from the paper eject section. 5 Press the upper unit down firmly on both sides to close it. If you press the upper unit down on only one side, the opposite side will not be fully closed. Make sure that the upper unit is firmly closed, and that the error code “C01” on the display disappears.
Paper Jam in the Feed Section 1 2 Remove the documents from the document tray and the eject tray. 3 Press the open/close button, and lift up the upper unit. Remove the removable tray or document eject support plate if they are installed on the document eject tray. Close the document eject tray extension if it is open. Lift up the upper unit gently until it comes to a stop.
5 Press the open/close button, and lift up the feed unit. Gently lift up the feed unit until it comes to a stop. Space Backup ount Only ew File g Option Manual Auto Semi-Auto 6 Remove the jammed paper from the feed section. File tion Manual Auto Semi-Auto 7 To close the feed unit, push the feed unit inwards as far as possible, and then release the feed unit. When you release the feed unit, it begins to slowly fall down. Do not apply unnecessary force to push the feed unit down.
8 When the feed unit has fallen as far as it can go, press down firmly on both sides to close it. If you press the feed unit down on only one side, the opposite side will not be fully closed. Make sure that you hear it click into place. ce Backup ly n Manual Auto Semi-Auto 9 Gently close the upper unit. Space E FILM Backup F Count Only 4 New File Scanner Feeding Option A Manual Auto Semi-Auto If you press the upper unit down on only one side, the opposite side will not be fully closed.
Removing the Intermediate Unit If small-size documents such as checks are jammed in the intermediate unit, follow the procedure below to remove the unit and remove the jammed paper. 1 Slide the intermediate unit upwards. 2 Pull down the intermediate unit towards you, and remove the upper pin. 3 Lift up the intermediate unit as it is to remove.
Attaching the Intermediate Unit Follow the procedure to attach the intermediate unit that you removed in the previous procedure. 1 Hold the intermediate unit at an angle, and hook the notches on both sides onto the lower pins. 2 Push in the intermediate unit as far as possible with it raised slightly off the pins. The intermediate unit cannot be pushed in unless it is raised off the pins. 4 Troubleshooting 3 Push the intermediate unit down.
Paper Feed Trouble If the document is not fed properly or the detection functions do not work smoothly, remedy the problem by following the remedies described below. Condition Cause and remedy Paper jam has occurred. ● Check the document to see if the size and thickness of the document are within the ranges supported by the scanner, and to see if the quality of the document paper is appropriate. Refer to cautions on handling documents. (See “About Documents” P.
Condition Cause and remedy Double feed cannot be detected. Double feed detection is not possible on documents 130 mm (5.1 in.) wide or less even if double feed detection is set to ON. Condition Skew error occurs even though paper is not being fed at an angle. This error occurs when the area 5 mm (0.2 in.) from the top edge of the original contains text or pictures or the original has a dark background. If this error occurs, turn skew detection OFF and scan the document again.
When the Scanned Image is Not Normal If there is a problem in the scanned image (image is not sharp or stripes appear in the image), one of the following may be a probable cause. Check as follows and take the appropriate remedy. Cause Remedy The scanning glasses and rollers on the scanner are dirty. Clean the scanning glasses and rollers. (See “Chapter 5 Daily Cleaning” P. 73) Cause Remedy The scan conditions are inappropriate. Check the brightness and other scanner settings.
When an Error Code is Displayed When the scanner unit malfunctions or when trouble such as a paper feed or eject error occurs, an error code appears on the counter display of the operation panel. The following describes error codes that appear on the counter display and how to remedy the error. C01 The upper unit or feed unit is open. Close the upper unit or feed unit. Error code Cause Remedy C04 The endorser cover is open. (when endorser is installed) Close the endorser cover.
Error code Cause Remedy H01 The optional imprinter’s ink cartridge is not installed. Install the imprinter cartridge. Error code Cause Remedy H02 Endorser (option) connection error Connect the endorser properly. Error code Cause H03 The imprinter ink cartridge is not mounted, or an endorser connection error has occurred. Attach the ink cartridge or endorser properly. Remedy Error code Cause Remedy J18 A document was skewed.
Chapter 5 Daily Cleaning This chapter describes daily cleaning of the scanner. Daily Cleaning ............................................
Daily Cleaning To ensure high-quality image scanning, regularly clean the DR-5060F as described below. CAUTION ● Before you clean the DR-5060F, remove the camera unit, turn the DR-5060F and computer OFF and disconnect the power cord from the power outlet. Failure to do so might cause electrical shock. ● Never clean the DR-5060F with any kind of volatile solution such as alcohol, benzene and paint thinner. Doing so might cause fire and electrical shock, or cause the exterior to disfigure or discolor.
Cleaning the Scanning Glasses and Rollers A probable cause of stripes appearing in scanned images or dirt appearing on scanned documents is dirt on the scanning glasses or rollers. Clean scanning glasses and rollers regularly. 1 Turn the power switch OFF, and unplug the power cord from the power outlet. 2 Remove the removable tray or document eject support plate on the document eject tray if it is installed. Close the document eject tray extension if it is open. 3 Lift up the upper unit.
5 Wipe the rollers with a firmly wrung cloth moistened with water or mild detergent while rotating the rollers. Rollers are located at the positions indicated in the figure below. Rollers Intermediate unit NOTE ● Remove the intermediate unit before wiping the rollers in the intermediate unit. (See “Removing the Intermediate Unit” P. 66) ● The drive rollers indicated in the figure below cannot be rotated by hand.
7 Use a clean, dry cloth to wipe the scanning glasses. Scanning glasses are located above and below in the feed unit. Wipe both of these scanning glasses clean. CAUTION Never spray mild detergent or water directly on the scanning glasses. The spray could penetrate below the glass, and contaminate the internal light source and lenses. Scanning glasses 8 Wipe the rollers with a firmly wrung cloth moistened with water or mild detergent while rotating the rollers.
NOTE ● If a roller on the feed unit becomes loose (Figure A), re-attach it as shown in Figure B. ● Before you return the upper unit to its original position, be sure to lower the lever on the feed unit (Figure B). If the document is scanned with the lever at the up position, a paper feed error will occur. 3. Lower the lever. 1. Fit into the deeper of the two grooves. Backup 2. Press this part.
11 Gently close the upper unit. Space E FILM Backup F Count Only New File Scanner Feeding Option A Manual Auto Semi-Auto 12 When the upper unit has fallen as far as it can go, press down firmly on both sides to close it. If you press the upper unit down on only one side, the opposite side will not be fully closed. Make sure that you hear it click into place. MEMO The error code “C01” will appear when the scanner is turned ON if both the upper unit and the feed unit are not fully closed.
Cleaning the Camera Unit ● Wipe the surfaces of the camera unit with a firmly wrung cloth moistened slightly with water or mild detergent. Then wipe off with a clean, dry cloth. ● Wipe the camera unit’s lens with a soft, clean cloth. CAUTION Take care not to scratch the lens when wiping it. ● Remove any dirt from the capstan roller with a firmly wrung cloth moistened slightly with water or mild detergent while rotating the roller.
Imprinter Guide Plate Ink adhering to the holes on the guide plate on the inside sometimes cause documents to become dirty when the imprinter is used. Clean these holes with a cotton wool bud.
Specifications Type Document size Document feeding Scanning method Light source Scan mode Desktop sheet fed type Width: 55 to 297 mm/2.2 x 11.7 in. Length: 70 to 432 mm/2.8 x 17.0 in. Thickness: 0.06 to 0.15 mm (0.002 in. to 0.005 in.) (auto feeding) 0.05 to 0.20 mm (0.001 in. to 0.007 in.
Dimensions with tray closed with tray open Weight Power requirement Power consumption Noise Operating environment 447 (H) x 535 (W) x 671 (D) mm [17.5 (H) x 20.8 (W) x 26.1 (D) in] 486 (H) x 535 (W) x 839 (D) mm [18.9 (H) x 20.8 (W) x 32.7 (D) in] Approx. 48 kg (105.8 lb.) AC 120 V (240 V in Europe) (50/60 Hz) 220 W Less than 70 dB Temperature: 10°C to 32.5°C (50°F to 90.
CANON ELECTRONICS INC. 1248, SHIMOKAGEMORI, CHICHIBU-SHI, SAITAMA 369-1892, JAPAN CANON U.S.A. INC. ONE CANON PLAZA, LAKE SUCCESS, N.Y.11042, U.S.A. CANON CANADA INC. 6390 DIXIE ROAD, MISSISSAUGA, ONTARIO L5T 1P7, CANADA CANON EUROPA N.V. BOVENKERKERWEG 59-61, 1185XB AMSTELVEEN, THE NETHERLANDS CANON LATIN AMERICA, INC. 6505, BLUE LAGOON DRIVE, SUITE 325 MIAMI, FLORIDA 33126 U.S.A. CANON AUSTRALIA PTY. LTD. 1 THOMAS HOLT DRIVE, NORTH RYDE, SYDNEY. N.S.W, 2113. AUSTRALIA CANON SINGAPORE PTE. LTD.