USRM1-9895-00 2011
Structure of the Users Guide Chapter 1 Before You Begin Chapter 2 Operating Procedures Chapter 3 Troubleshooting Chapter 4 Appendix Read here first.
Important Information • This manual is designed to help you to install, operate and maintain the trimmer. Please read and understand this manual, and keep it in a safe and convenient place. • Do not operate the trimmer until you read and understand the instructions in this manual.
Safe Use of Machine To use this machine safely, proper operation and periodical maintenance are indispensable. Read the safety precautions described in this manual thoroughly, and do not perform operations or maintenance procedures until you understand them completely. The operating procedures and safety precautions described in this manual are valid only for proper use of this machine. Responsibility for any improper use or operation of this machine, lies with the user.
Caution Label Locations When removing jammed booklets from the trim section, take care not to touch the blade. When removing jammed booklets from Infeed section, do not put your hands and fingers close to the belt. Otherwise, if the belt drives by some chance, your hands and fingers may be caught. FCC NOTICES NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
CONTENTS Important Information ...............................................................................................................i Safe Use of Machine ...............................................................................................................ii Operating Safety Precautions ..................................................................................................ii Caution Label Locations ................................................................................
Before You Begin 1 CHAPTER Machine Description ............................................................................................................................ 1-2 Section Descriptions ............................................................................................................................ 1-3 [1] Infeed Section ............................................................................................................................ 1-3 [2] Trim Section...................
Machine Description [6] [5] [4] [3] [2] [1] Infeed Section (See page 1-3.) [2] Trim Section (See page 1-4.) [3] Booklet Lifter Section 1 (See page 1-5.) [4] Booklet Lifter Section 2 (See page 1-6.) [5] Front Cover [6] Conveyor Section (See page 1-7.
Section Descriptions [1] Infeed Section Booklets delivered from the host machine are received here. The booklets are jogged, and then transported to the trim section. Once the trimmer is installed, you cannot touch this section. When booklet jams in this section, pull out the trim unit and remove the jammed booklet from the space on the trim unit (See page 1-4.). Top-bottom Guides These guides jog the booklet. Transport Hooks These hooks push each booklet into the trim section.
[2] Trim Section Each booklet delivered from the Infeed Section is trimmed along its fore-edge, and then moved to the booklet lifter section. To pull out the trim unit, hold the green handle. CAUTION Trim Section Transport Belt Unit [TC4] When booklets jam in the trim section, hold the handle with green label and open this mechanism to remove the jammed booklets. Opening the Transport Belt Unit 1. Hold and press the handle. 2. Open to the right.
[3] Booklet Lifter Section 1 This section lifts each booklet and delivers. Locking Lever Booklet Lifter Section Belt Unit [TB] If a booklets jam in the booklet lifter section, hold the green locking lever and open this mechanism to remove the jammed booklets. Opening the Transport Belt Unit 1. Hold the locking lever. 2. Turn the lever to the left. Closing the Transport Belt Unit 1. Hold the locking lever. 2. Push the mechanism to the right until it is locked.
[4] Booklet Lifter Section 2 This section delivers each booklet to the conveyor. Delivery Section Cover If a booklets jam in the delivery section, open this cover and remove the jammed booklets. Transport Belts These belts move the booklets. 1-6 Section Descriptions Delivery Section Transport Belt Unit [TA] If a booklets jam in the delivery section, hold the handle with green label and open this mechanism to remove the jammed booklets. Opening the Transport Belt Unit 1. Lift the handle up. 2.
[5] Conveyor Section The booklets delivered from the booklet lifter section are laid out on the conveyor. Handle [TE] Hold this handle and lift the roller unit when removing the booklets on the conveyor. Delivery Transport Rollers Output booklets are held by this roller. The position of the roller is set automatically to match the booklet size. Booklet Detect Sensor This sensor detects the conveyor full with stacked booklets.
1-8 Section Descriptions
Operating Procedures 2 CHAPTER Trimmer Setup ..................................................................................................................................... 2-2 Operation While Trimming ...................................................................................................................
Trimmer Setup 1 Turn on the power switch on the saddle stitcher first, then turn on the power switch on the host machine (printer). Trimmer will also be powered on because it is connected to the saddle stitcher. See the operation manual for the printer and set up the printer.
Operation While Trimming When the conveyor is full with booklets, remove the booklets. If the machine stops because the conveyor is full, remove the booklets, and the operation restarts automatically. · If you remove booklets before the conveyor is full, you can increase production efficiency, without interrupting the operation. · Be careful not to drop the book while removing.
If a booklets jam, open the cover or mechanism shown below to remove the jammed booklets. Delivery Section Cover Transport Belt Unit Front Cover Trim Unit CAUTION When removing jammed booklets from the trim section, take care not to touch the blade edge. · If the booklets jam frequently, refer to page 3-4 for instructions on correcting the problem.
Troubleshooting This section describes the cause and solution of the errors. 3 CHAPTER Error Messages.................................................................................................................................... 3-2 Service Call Error............................................................................................................................ 3-2 Error Message Chart.........................................................................................................
Error Messages When an error occurs and the machine does not work properly, “SERVICE CALL ERROR” appears on the LCD of the host machine (printer). If “SERVICE CALL ERROR” appears, perform as follows: WARNING Do not plug in or pull out the power plug with wet hands. It may cause an electrical shock. CAUTION When you pull the power plug out, be sure to hold the plug as you do so.
Error Message Chart Perform the required remedies according to the error indicated on the host machine (printer). E 2 B A C4 C3 D 1 C2 3 CAUTION C1 When removing jammed booklets from the trim section, take care not to touch the blade edge. Cause of Error Remedy The delivery section cover is open. Close the delivery section cover 2 . The front cover is open. Close the front cover 1 . The trim unit is not inserted correctly. Hold the handle end correctly.
Clearing Paper Jams Jam in Conveyor Section • Paper chip jams. (See procedure 1.) • Transport belts are dirty. (See procedure 2.) Jam in Booklet Lifter Section 2 • Paper chip jams. (See procedure 1.) • Transport belts are dirty. (See procedure 2.) Jam in Booklet Lifter Section 1 • Paper chip jams. (See procedure 1.) • Transport belts are dirty. (See procedure 2.) Jam in Infeed Section • Paper chip jams. (See procedure 1.) • Transport belts are dirty. (See procedure 2.
Appendix 4 CHAPTER Specifications ....................................................................................................................................... 4-2 Index ....................................................................................................................................................
Specifications Specifications Product Name Booklet Trimmer-D1 Description of Product Upper knife reciprocating fore-edge trimmer with delivery tray Maximum Number of Sheets Trimmable *1, *2 50 sheets (80 gsm), 48 sheets (80 gsm) + 2 sheets (300 gsm) Possible Trimming Size*3 A3, B4, A4R, 13" x 19.2" (330.2mm x 487.7 mm), 12" x 18", 11" x 17", LGL, LTRR, 12.60" x 17.72" (320 mm x 450 mm [SRA3]) (Above sizes are native sheet sizes before half folded.) Possible Trimming Width Fore edge : 2 to 20 mm (0.
Index B P Booklet Lifter Section 1 ............................ 1-2, 1-5 Booklet Lifter Section 2 ............................ 1-2, 1-6 Booklet Lifter Section Belt Unit .......................1-5 Paper Jams ...................................................... 3-4 C S Service Call Error............................................. 3-2 Specifications ................................................... 4-2 Conveyor Section ..................................... 1-2, 1-7 T D Delivery Section Cover .....
4-4 Index
CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan CANON U.S.A., INC. One Canon Plaza, Lake Success, NY 11042, U.S.A. CANON CANADA INC. 6390 Dixie Road Mississauga, Ontario L5T 1P7, Canada CANON EUROPA N.V. Bovenkerkerweg 59-61 1185 XB Amstelveen, The Netherlands (See http://www.canon-europe.com/ for details on your regional dealer) CANON LATIN AMERICA, INC. 703 Waterford Way Suite 400 Miami, Florida 33126 U.S.A. CANON AUSTRALIA PTY. LTD 1 Thomas Holt Drive, North Ryde, Sydney, N.S.W.
