Service Manual

ManualsBrandsCanon ManualsDrumsCanon Creative park

View of completed model

Front Right side

Left sideBack

PAGE01

Drum set : Assembly Instructions

Parts sheet (Pattern) : Twenty-two A4 sheets (No.1~No.22)

No. of Parts : 384

Assembly Instructions : Ten A4 sheets (No.1~No.10)

*Build the model by carefully reading the Assembly Instructions, in the parts sheet page order.

*Assembly will be easier if you write the part's number on the back of each part.

A drum set is a collection of various types of drums, cymbals and other percussion instruments that are

lined up in a formation that makes them easily played by one person. The number and type of

instruments included can be arranged according to the performer's preference or characteristics of the

music. The performer usually plays seated on a stool. The idea for the drum set is said to have

originated in military bands, when a cymbal was placed on top of the bass drum to make it easier for

the performer holding it. This was followed by the idea to use a pedal to play the bass drum with the

foot, and the invention of the hi-hat, two cymbals on top of each other that are clashed together. These

adaptations have resulted in the drum set up and beat style we know today.

Trace along the folds with a ruler and a used pen (no ink) to

get a sharper, easier fold.

Handy Hint

Mountain fold (dotted line)

Make a mountain fold.

Glue, scissors and other tools

may be dangerous to young

children so be sure to keep them

out of the reach of young

children.

Scissors, set square, glue (We

recommend stick glue),pencil,

used ballpoint pen, toothpicks,

tweezers,

(useful for handling small parts)

Assembly tip CautionAssembly Instructions Tools and materials

Valley fold

(dashed and dotted line)

Make a valley fold.

Scissors line (solid line)

Cut along the line.

Cut In line (orange solid line)

Cut a slot.

Cut out (orange shaded)

Cut out the area marked.

The glue spot(colored dot)

shows where to apply the glue.

Glue spot (Red dot)

Glue parts with the same number together.

Glue spot (Green dot)

Glue within the same part.

Glue spot (Blue dot)

Glue to the rear of the other part.

Glue spot (Yellow dot)

Apply glue to the back, and attach to the back of the other parts.

Before gluing, crease the paper

along mountain fold and

valley fold lines and make sure

rounded sections are nice and

stiff.

Summary of content (10 pages)

PAGE 1
Drum set : Assembly Instructions Front Right side Back Left side View of completed model A drum set is a collection of various types of drums, cymbals and other percussion instruments that are lined up in a formation that makes them easily played by one person. The number and type of instruments included can be arranged according to the performer's preference or characteristics of the music. The performer usually plays seated on a stool.
PAGE 2
Drum set : Assembly Instructions Before starting. Each page of the "Parts sheet" has a sheet number in the top left-hand corner (Sheet No.1~No.22). Work in order of these sheet numbers. (The parts for assembly are on pages 2 ~ 22.) There are 384 parts in total, and each part is numbered according to its page. Also, the glue spots on each part are marked with the number of the part to attach to them. PAGE03 Align the marker lines on 3A and 3B with the glue spots on 3C ~ 3H, and attach.
PAGE 3
Drum set : Assembly Instructions PAGE04 PAGE05 Bass drum Bass drum *Roll up and attach. Seam line Inside Align the seam lines and insert the pieces inside each other, and attach to the specified position. Wrapping the piece around a thin cylindrical object will result in a neater finish. Face the seam line inwards and insert the piece to the position specified. PAGE06 *Attach the back.
PAGE 4
Drum set : Assembly Instructions Upper part PAGE06 *Be sure to align the thick black marker lines on the top and bottom (circled here in blue) when attaching. PAGE07 Tom-tom 13" x 10" Tom-tom 12" x 9" *Take note of where the thick marker line is. *Align the reverse sides and attach. Align the marker lines on 7A and 7B with the glue spots on 7C ~ 7H, and attach. Lower part *Before attaching parts 6O and 6P, bend them into shape as shown in the diagram. *Begin from the opposite side to the seam.
PAGE 5
Drum set : Assembly Instructions PAGE02 03 04 05 06 07 PAGE08 Bass drum / Tom-tom 13" x 10" / Tom-tom 12" x 9" Floor tom *Begin from the opposite side to the seam. Upper part Shell Lug Tom holder Head Seam Lower part Lug Bass drum bar Bass drum front head Bass drum hook Tom-tom 13" x 10" *NB: There are 16 8H parts altogether. *Before attaching parts 8F and 8G, bend them into shape as shown in the diagram.
PAGE 6
Drum set : Assembly Instructions Upper part PAGE09 Align the marker lines on 10A and 10B with the glue spots on 10C ~ 10H, and attach. Floor tom *Be sure to align the thick black marker lines on the top and bottom (circled here in blue) when attaching. *Take note of where the thick marker line is. *Align the reverse sides and attach. Lower part Snare wire picture Head Upper part Lower part Lug *Align the snare wire position here. Shell *Do not apply glue to .
PAGE 7
Drum set : Assembly Instructions PAGE12 *Align the reverse sides and attach. PAGE13 Ride cymbal *Align the reverse sides and attach. *Align the reverse sides and attach. Cymbal stand nut *Align the reverse sides and attach. Crash cymbal Felt for clutch *Align the seams and attach. *Align the seams and attach. Cymbal *Align the reverse sides and attach. *Align the seams and attach. *Align the seams and attach.
PAGE 8
Drum set : Assembly Instructions PAGE14 PAGE14 15 Hi-hat cymbal Hi-hat cymbal *Align the seams and attach. *Back side of 14C Extension rod *Align the seams and attach. Hi-hat clutch *Align the seams and attach. Hi-hat cymbal *Align the seams and attach. *Align the reverse sides and attach. Die-cast joint Curl. Stand *Roll up and attach. *Roll up and attach. *Do not apply glue to . *Put the pieces back to back and attach together.
PAGE 9
Drum set : Assembly Instructions PAGE15 PAGE16 Drum pedal Drum stool *Align the reverse sides and attach. *Back side of 16B *Align the reverse sides and attach. *Roll up and attach. *Bend the pieces left and right to open a gap. Seat Do not apply glue. *Align the reverse sides and attach. Leg Felt beater Frame Rubber foot Foot pedal *The felt beater moves when you press the foot pedal.
PAGE 10
Drum set : Assembly Instructions PAGE21 22 PAGE17 18 19 Display stand Display stand PAGE20 21 Display stand Ride cymbal Crash cymbal Tom-tom 13" x 10" Tom-tom 12" x 9" Hi-hat cymbal *Fold inside and attach. Snare drum Floor tom Drum stool Bass drum Drum pedal View of completed model *The completed photo is an image of a basic drum set. The parts can be arranged to your liking.