Operating instructions

CLASSIC 5350SE SPECIFICATION
Measured at 230 V or 115 V
Not recommended for use into more than 2 pairs of 8
ΩΩ
loudspeakers
POWER OUTPUT (both channels into 8Ω) 90 Watts
POWER OUTPUT (one channel into 8Ω) 110 Watts
POWER OUTPUT (one channel into 4Ω) 180 Watts
PEAK OUTPUT CURRENT INTO 1Ω > 25 Amps RMS
TOTAL HARMONIC DISTORTION < 0.05%
(20 Hz to 20 kHz)
FREQUENCY RESPONSE 3 Hz to 25 kHz - 1 dB
SLEW RATE > 50 V per
µ S
GAIN (Power amp only. Passive pre) x 48 or 33.6 dB
INPUT SENSITIVITY - One channel driven/8Ω 620 mV line input/power amp input
PRE-AMP OUTPUT LEVEL Follows input signal level via volume control
SIGNAL TO NOISE RATIO (‘A’ weighted) > 105 dB
SEPARATION (line inputs) > 60 dB at 1 kHz
MM PHONO SENSITIVITY & IMPEDANCE 3.5 mV 47 kΩ (when fitted)
MC PHONO SENSITIVITY & IMPEDANCE 0.75 mV 1 kΩ (when fitted)
POWER CONSUMPTION (at idle) 40 W
POWER CONSUMPTION (full power 10% THD) 340 W
WEIGHT (net) 7 kgs 15.5 lbs
SIZE (W x H x D) 430 x 70 x 280 mm 17” x 2.4” x 11”
MAINS VOLTAGE @ 60Hz 100V Japan 115V North America
@ 50Hz 230/240V Europe, Asia and UK
REMOTE HANDSET ARC53 SUPPLIED
MAINS VOLTAGE AND FREQUENCY IS INTERNALLY SET FOR THE COUNTRY OF USE
Creek Audio Ltd reserves the right to change or modify the specification of its products without prior warning.
Classic 5350SE
Designed and manufactured
in the United Kingdom
Thank you for purchasing the Classic 5350SE. You are now in possession of a State of the Art
integrated amplifier. The functions and operation of the Classic 5350SE are very simple. However, the
following notes are provided to explain all aspects of its design and use.
12 Avebury Court, Mark Road, Hemel Hempstead HP2 7TA, England
Tel: [phone] Fax: [phone]
E-mail: [e-mail] Internet: www.creekaudio.com
Creek Audio Ltd
When unpacking the amplifier please keep the packing material in a safe place for possible future use.
In the pack there is a separate mains cable suitable for connecting to the mains supply in the country
of use. The IEC socket end of the cable should be firmly inserted into the connector on the rear panel
marked "Mains Input".
Remember, do not overload the mains wall socket with too many plugs or adaptors. The high quality
performance of the amplifier will be impaired if the electrical supply to it is in poor condition. If in doubt,
consult a qualified electrician or your dealer.
The "Mains Input" connection is also fitted with a fuse, specifically suited to the supply voltage of the
country of use. The correct value is clearly marked on the rear panel next to the Mains Input.
Should it be necessary to replace the fuse, ensure that you use the same type as specified on the rear
panel, i.e. 5 x 20mm cartridge type: T 3.15 A surge resisting for 220-240V 50Hz AC,
T 6.3 A surge resisting for 110-120V 60Hz AC
T 8A surge resisting for 100V (Japan)
MAINS CONNECTION
The rotary selector switch on the left-hand side of the amplifier is used to select and listen to any of the
desired inputs. There are six inputs including tape in plus tape out.
As all the line input levels are the same, it is not necessary to use the precise inputs as designated.
You may, for example, plug a CD player into the Tuner input and obtain exactly the same result or
performance as the dedicated CD input. However, for added flexibility, the first input on the Classic
5350SE can be used either for vinyl disc or auxiliary line. To connect your turntable, it is necessary to
have the optional MM or MC phono plug-in board fitted. Alternatively Creek Audio produces a separate
range of phono pre-amplifers. Ask your dealer for full details.
The pre-amp output and the power amp inputs are available through RCA sockets on the rear panel.
For most applications it is necessary to join these two connections to patch the input signal through to
the internal power amp. This is the default setting from the factory. However, when used with an
external device, such as a sub-woofer or graphic equaliser etc. it may be necessary to separate the
pre and power amps. To do this there is a switch placed next to the two sets of sockets, recessed behind
the rear panel to avoid accidental use. To join or separate the sockets, it is necessary to push the
recessed button with a matchstick or similar device. When joined the button is in the out position.
Switch the amplifier off before making any changes in order to avoid any pops, clicks or other noises.
INPUT CONNECTION AND SWITCHING
If within two years of puchase date your Classic 5350SE proves to be defective for any reason other than
accident, misuse, neglect, unauthorized modifcation, or fair wear and tear, Creek Audio Ltd. will, at its
discretion, replace the faulty parts without charge for labour or return carriage within the U.K. This
warranty is valid only in the U.K. and given in addition to statutory rights. Service enquiries outside the
U.K. should be addressed first to the supplying dealer and/or the Creek distributor/importer. Warranties
granted in these countries are entirely at the discretion of the distributor.
OPERATING
INSTRUCTIONS