CD-R Print Guide Table of Contents Preface 1 Introduction Printing on CD-Rs/DVD-Rs (CD-R Direct Print) XXXXXXXX ©CANON INC.
Preface Introduction This CD-R Print Guide uses the following symbols to indicate important information. Always observe the instructions indicated by these symbols. Instructions that, if ignored, could result in death or serious personal injury caused by incorrect operation of the equipment. These must be observed for safe operation. Instructions that, if ignored, could result in personal injury or material damage caused by incorrect operation of the equipment. These must be observed for safe operation.
Printing on CD-Rs/DVD-Rs (CD-R Direct Print) The CD-R tray feeder and tray (supplied) allow the printing of images on CD-Rs or DVD-Rs (printable discs). The "CD-LabelPrint" software provided on the CD-ROM edits and further processes the images for printing.
Attaching the CD-R Tray Feeder and CD-R Tray Attaching the CD-R tray feeder 1 Pull down the paper output tray cover forward to open. Do not extend the paper output tray. Doing so will prevent the attaching of the CD-R tray feeder. Paper output tray cover 2 Place the CD-R tray feeder on the paper output tray. 3 Insert the CD-R tray feeder straight by sliding it in until it clicks into place. 4 Push in the slider on the CD-R tray feeder. Insert the slider up to here. Insert the slider completely.
Placing the CD-R/DVD-R on the CD-R Tray When placing the CD-R/DVD-R on the CD-R tray, do not touch the printing surface of the disc or the reflectors on the CD-R tray. 1 Place the disc on the CD-R tray with the printable surface facing up. Reflector When printing on an 8 cm CD-R, attach the 8 cm CD-R adapter (provided). Otherwise, printing quality will be reduced and the CD-R might be damaged. 4 1 Align the protrusions on both edges of the 8 cm CD-R adapter with indentations on the CD-R tray.
Placing the CD-R tray 1 Place the CD-R tray on the CD-R tray feeder. Align these two arrows ( ). 2 Insert the CD-R tray so that the arrow ( ) on the CD-R tray feeder is almost aligned with the arrow ( ) on the CD-R tray. Ensure that the CD-R tray does not exceed this point. When printing on the CD-R, see "Printing on CD-Rs/ DVD-Rs." (See page 7 for Windows and page 9 for Macintosh.) Removing the CD-R Tray Feeder and CD-R Tray Removing the CD-R tray 1 Pull out the CD-R tray to remove it.
When removing the 8cm CD-R, remove the adapter first, and then remove the disc from the tray. Removing the CD-R tray feeder 1 Hook your fingers inside the groove on the slider, and pull the slider in the direction of the arrow. 2 Remove the CD-R tray feeder from the printer. Be sure to perform steps 1 and 2 in order when removing the CD-R tray feeder. Performing them at once may result in damage to the CD-R tray feeder.
Printing on CD-Rs/DVD-Rs - Windows This section explains how to use CD-LabelPrint to print directly on 12 cm CD-Rs and DVD-Rs. Refer to the CD-LabelPrint’s manual for more information about this procedure. To access the manual from the Start menu, click All Programs (or Programs for Windows Me/Windows 2000/Windows 98), CD-LabelPrint, and select Manual. Importing the image to print on the CD-R/DVD-R 1 Select All Programs (or Program), CD-LabelPrint, and then CDLabelPrint to start CD-LabelPrint.
Printing on the CD-R/DVD-R 1 Click Print. The Print CD Labels dialog box appears. 2 Click Printer.... • The Printable Label image on the Print CD Labels dialog box shows the print image of the CD-R tray (rectangle) and the CD-R (circles). The leading edge of the CD-R tray is at the bottom of the image. • If the "[Dark]" setting produces unsatisfactory results (e.g. if images are too dark or characters appear blurred), select "[Light]". Print quality on CD-R/DVD-R may vary depending on the media you use.
Printing on CD-Rs/DVD-Rs - Macintosh This section explains how to use CD-LabelPrint to print directly on 12 cm CD-Rs and DVD-Rs. Refer to the CD-LabelPrint’s manual for more information about this procedure. To access the manual, double-click Manual in the CD-LabelPrint folder. Importing the image to print on the CD-R/DVD-R 1 Select Applications from the GO menu. Double-click the CD-LabelPrint folder, and then CD LabelPrint to start CD LabelPrint. 2 Click Paper Selection.
Printing on the CD-R/DVD-R 1 Select Page Setup… in the File menu. The Page Setup dialog box opens. 2 Specify the required settings. Format for : Select the printer connected to your printer. Paper Size : Select CD-R tray. Orientation : Select the portrait icon. Scale : Enter 100%. 3 Click OK. 4 Click Print. The Print Label Sheet edit box opens. 5 Confirm the changes you made, then click Print. The following dialog box shows the print image of the CD-R tray (rectangle) and the CD-R (circles).
7 Click the Quality & Media tab. 8 Select Printable disc (recommended) or Printable disc (others) from Media Type. If the "Printable disc (recommended)" setting produces unsatisfactory results (e.g. if images are too dark or characters appear blurred), select "Printable disc (others)". Print quality on CD-R/DVD-R may vary depending on the media you use. 9 Click Print. Refer to the CD-LabelPrint’s manual for details on CDLabelPrint.
Troubleshooting Cannot print on CD-Rs or DVD-Rs Possible Cause Try This CD-R direct print does not begin Ensure that the CD-R tray feeder, or the CD-R tray is properly installed. Correctly install the CD-R tray feeder, or the CD-R tray, and then press the RESUME/CANCEL button to restart the printing process. Please refer to “Attaching the CD-R Tray Feeder and CD-R Tray” on page 3 for proper placing operation. Ensure that the CD-R, or the DVD-R is properly placed on the tray.
CD-R Printing Errors Displayed in Windows Possible Cause Try This CD-R tray or CD-R/ DVD-R not in place Correctly attach the CD-R tray or load CD-R/DVD-R, and press the RESUME/ CANCEL button. CD-R/DVD-R not recognized correctly Some CD-Rs/DVD-Rs are not recognized correctly. If this happens, click Detects a printable disc on the CD-R tray at Custom Setting on the Maintenance tab to clear the check box, and print. When printing is over, select the Detects a printable disc on the CD-R tray check box.
CD-R Printing Errors Displayed in Macintosh Problem Possible Cause Try This Macintosh “Error No: 1001” CD-R tray or CD-R/ DVD-R not in place Correctly attach the CD-R tray or load CD-R/DVD-R, and press the RESUME/CANCEL button. Macintosh “Error No: 1001” CD-R/DVD-R not recognized correctly Some CD-Rs/DVD-Rs are not recognized correctly. If this happens, click Detects a printable disc on the CD-R tray at Custom Setting on BJ Printer Utility to clear the check box, and print.
The POWER Lamp Flashes Orange When a printer error occurs, the POWER lamp flashes. The number of flashes indicates the type of error. Count the flashes and take the appropriate action to correct the error. This section deals with errors on the CD-R tray only. For other errors, refer to the User’s Guide. Number of flashes Possible Cause Try This Two flashes CD-R Tray not in place Ensure that the CD-R/DVD-R is in place, insert the CD-R Tray correctly, then press the RESUME/CANCEL button.
16
CD-R Print Guide Table of Contents Preface 1 Introduction Printing on CD-Rs/DVD-Rs (CD-R Direct Print) XXXXXXXX ©CANON INC.