Table of Contents These materials explain the procedure for receiving Canon EOS C70 (with a 3rd party USB-C Ethernet adapter – sold separately) IP streaming with the “VLC” application installed on a PC. (Please refer to www.videolan.org for system requirements).
1.IP Streaming (“VLC” Application) Setup 1-1 Things to Prepare ① Canon EOS C70 (with a 3rd party USB-C Ethernet adapter – sold separately). ② PC (with VLC application installed from www.videolan.org) *Operation checks have been performed with VLC Version 3.0.12.
・For the IP address, input [192.168.0.xxx] For example: [192.168.000.002] ・For the subnet mask, input [255.255.255.0] *Generally, the subnet mask values will be entered automatically once you input the IP address. 3.Canon EOS C70 Network Settings 3-1 Set Network Connection 3-1-1 Select System Frequency ① From MENU, go to [Recording/Media Setup] menu ② Select [System Frequency] ⇒ Press SET ③ Select [59.94 Hz / 50.00 Hz / 24.
3-1-2 Enable Network ④ From MENU, go to [Network settings menu] ⑤ Select [Network] ⇒ Press SET ⑥ Select [Enable] ⇒ Press SET 3-1-3 Select New Connection Setting ① Select [New Conn.
② Select [IP Streaming] ⇒ Press SET ③ Confirm a new Connection Setting ⇒ Press OK 3-1-4 Create New Communication Setting ① Select [Create New Comm.
3-1-5 Setup with Network Connection ① Select [Setup with Network Connection] ② ⇒ Press SET ③ Under IP Address Settings (IPv4), select [Manual Setting] ⇒ Press SET ④ Select [IP Address] ⇒ Press SET
⑤ Input [192.168.0.xxx] as the IP address. Example: [192.168.0.3] ⇒ Press SET *These values are the address in the C70 itself has. Set the values at the end so that they are not the same as those of the device you are connecting to (the values set on the PC). ⑥ Select [Subnet Mask] ⇒ Press SET ⑦ Input [255.255.255.
⑧ [Use Gateway] ⇒ Disable ⑨ [DNS Address] ⇒ Disable ⑩ Save IP Address Setting (IPv4) ⇒ Press OK
⑪ [TCP/IPv6 Settings] is not necessary for the assumed connection format of these materials, so you can select Disable ⇒ Press SET ⑫ Confirm Communication settings ⇒ Press OK 3-2 Prepare for Streaming Transmission 3-2-1 Create New Function Setting ① Select [Create New Func.
3-2-2 Select Protocol ① Select [UDP] or [RTP] or [RTP+FEC] or [RTSP+RTP] ② ⇒ Press SET (The [UDP] protocol will be selected for this example). [UDP]: This protocol prioritizes transfer speeds but does not guarantee the reliability/integrity of the data. Lost or delayed IP packets are ignored. [RTP]: Standard protocol for video/audio broadcasts over the internet. Lost or delayed IP packets are ignored.
② Input the Destination Server ⇒ Press OK Input the Destination Server of the device you are connecting to (PC), select [Set], ⇒ Press OK Example: [192.168.0.2] (The PC’s IP address set in advance.) If necessary, input the [Dest. Port No.] in the same way, select [Set], ⇒ Press OK ● Normally, the port number initially set is used (it is normally 5000).
③ Confirm [Destination Server] and [Dest. Port No.] ⇒ Press OK 3-2-4 Select Bit Rate and Resolution ① Select bit rate and resolution. Select any option ② ⇒ Press SET 3-2-5 Select Audio Out Channels ① Select audio output channels [CH1/Ch2], [CH3/Ch4] ② ⇒ Press SET (*For the audio to record, from MENU [ Audio settings] ⇒ [Select CH1/CH2 Input] and [Select CH3/CH4 Input], you can select any of [INPUT terminal / MIC terminal / Internal mic.
③ Save Function Settings ⇒ Press OK 3-2-6 Connection Setting Save Destination ① Select [Conn. Setting] ② ⇒ Press SET ・Twenty (20) connection settings (SET) that can be registered. Push the joystick up and down to scroll down the screen.
④ Now, you will notice the [ ] Ethernet icon on top of the screen. This icon indicates that the ethernet connection on the camera is now active. 4.
② Select Enable ⇒ Press SET ③ Now, [ ] IP streaming is activated. ● The C70 will show a [ ● On the screen, the [ ] icon showing the connection method. ] icon will be shown in white and video/audio streaming transmission will start. ● When [Off] is selected for [Network Functions], transmission will terminate, and the [ disappear.
PC: 4-2 Perform VLC settings on the PC ① Open the VLC Media Player ② Select [Media] ③ Select [Open Network Stream] ⇒ In the [Please enter a network URL] cell, input the network URL that matches the protocol that was selected under the protocol settings earlier (under 3-2-2 in the guide). For this example, input 【udp://@:5000】 and click [Play (P)▼]. ⇒ If successful, the images will appear on the screen. *Notes: ・Recording to the SD card during IP streaming is not possible.