USER MANUAL
CONTENT SAFETY INFORMATION P3-4 Read Before Use Maintaining The Device Waterproof Cautions OVERVIEW P5 Supplied Items Product Features GETTING STARTED P6-9 Charging Inserting/Removing MicroSD Card Power ON/OFF First Time Pairing With Your Smartphone Camera Default Settings OPERATIONS P10-11 Wireless Mode Photo Mode Video Mode Multi Mode LED INDICATIONS P12 ACCESSORY P13 TROUBLESHOOTING P14 SPECIFICATIONS P15 2
SAFETY INFORMATION READ BEFORE USE Please read the following instructions and safety precautions before using the device. For regulatory and additional safety information, refer to the Regulation and Warranty Information sheet included in your package contents. RMN: PG1001 Regulatory Model Identification Number is assigned for regulatory identification purpose. WARNING Used to indicate a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION Used to indicate the level of a hazard or damage which, if product is handled erroneously, may result in injury or property damage other than product faults. • Electromagnetic interference or electrostatic discharge may cause the device to malfunction or the MicroSD card memory to be lost or altered. Should this occur, use a pin with blunt end to press the [RESET] button at the backside of the device for more than 10 seconds. See Diagram A on page 6 for exact location of reset button.
MAINTAINING THE DEVICE • Please charge the device at the recommended temperature of 59º to 90ºF (15º to 32ºC). • Use and keep the device in the recommended environment of 59º to 90º F (15º to 32ºC). Avoid using or storing the device in humid or dusty place. • After the device is exposed to dirty water, rinse it with fresh water and dry it completely with a soft cloth. • The device has a shockproof to 2M (6.6 ft.). However, strong impacts could scratch the device and cause it to malfunction.
OVERVIEW SUPPLIED ITEMS Camera Tips Regulation and Warranty Information Sheet USB Cable PRODUCT FEATURES DIAGRAM A 2 4 3 5 1 6 11 9 8 10 13 14 7 12 16 15 Camera Lens Mode LED Detachable Faceplate Status LED Side Cover MicroSD Card Slot (up to 256GB) Latch Release Button Micro USB Port Wristband Eyelet Shutter Button Tripod Screw Hole Microphone Clip Speaker Reset Button ON/OFF/Mode Dial Switch *To reset all parameters into default setting, turn on the device, then use a pin with
GETTING STARTED CHARGING MODE LED Charging: Red Fully Charged: Green Press on the latch release button, and slide the Side Cover upward to open it. Insert the smaller end of the supplied USB cable into the device and other end into a chargeable USB adapter. The Mode LED will turn red to indicate charging. Once fully charged, the Mode LED will turn green. -- Operating time may vary depending on the battery status, operational status and environment conditions.
INSERTING/ REMOVING MicroSD CARD INSERT AND REMOVE THE MicroSD CARD • Press on the latch release button and slide the Side Cover upward to open it. • Insert the MicroSD card into the MicroSD card slot inside the Side Cover. When the card is fully inserted, you will hear a slight click and the card will not extend above the slot. • Push on the top of the MicroSD card to release it. Gently pull it out to fully remove it from the device. • If there is an error reading /writing to the MicroSD card.
An external MicroSD card (up to 256 GB) is needed for saving captured photos and videos. Only FAT16, FAT32 and exFAT formats are supported. Class 10 or above is recommended for a satisfying user experience. Use the following memory cards (sold separately) • MicroSD memory cards *1 • MicroSDHC memory cards *1 *2 • MicroSDXC memory cards *1 *2 *1 Cards conforming to SD standards. However, not all memory cards have been verified to work with the camera. *2 UHS-I memory cards are also supported.
POWER ON/OFF • Turn the mode dial from OFF to any other modes, the device will turn on in around 4 seconds. • Turn the mode dial to OFF to turn off the device. AUTO POWER OFF The device will power off automatically when idle for 3 minutes (by default). • User can restart the device by pressing the Shutter Button or turning the Mode Dial to any mode. • User can change the time for Auto Power Off (3 minutes / 5 minutes / 10 minutes) using the Canon Mini Cam App.
CAMERA DEFAULT SETTINGS Your camera has following default settings and options.
OPERATIONS WIRELESS MODE Connect your device with compatible smartphone for the operations below: • Remote shoot photo/video • Live View for Photo/Video Capturing • Access DCIM folders stored in MicroSD Card, including View/Delete/Download to Smartphone or Edit. PHOTO MODE • Press the Shutter Button to capture a photo. • There may be a delay before capturing the next image. • Press and hold the Shutter Button to shoot continuously.
MULTI MODE You can either capture photo or record video using different shutter operation. PHOTO • Press the Shutter Button once to capture a photo. • Continuous photo capture is not available in Multi Mode. VIDEO • Press and hold the Shutter Button for at least 4 seconds to start video recording. • Video recording will start after a single photo is captured. Keep holding the Shutter Button to continue recording video. • Video recording will stop once you release the Shutter Button.
LED INDICATIONS Status LED Mode LED Status Powered On & Standby (Photo/Video/Multi/ Wireless Modes) Powered Off/ Auto-Power off Mode LED Status LED Green Off Low Battery Red (Blink rapidly) Charging Red Fully charged Green Bluetooth® pairing Green > Red (Looping) Wi-Fi® connected Green Photo captured and saved Red (Blink once) Video recording Red (Blink slowly) Mass Storage mode Green Data transferring under Mass Storage mode Green (Blink rapidly) Firmware updating Green (Blink slowly) 14
ACCESSORY DETACHABLE FACEPLATE The device has a detachable faceplate. Gently lift up the detachable faceplate to remove it. Customize the device by changing the faceplate. * * Additional faceplates are sold separately.
TROUBLESHOOTING When the status LED blinking in red rapidly, it may related to the below reasons. Error Device does not work Actions • Make sure the battery level is not too low. If it is, recharge the device • Press the reset button for 10s to restart if the device is unresponsive • Make sure the MicroSD card is inserted without card error • Make sure the firmware is up to date or successfully upgraded.
SPECIFICATIONS Photo Resolution Approx. 13MP Video Resolution Video Format Zoom 1080p 60fps 1080p 30fps 720p 30fps (Supports Live View recording) MPEG-4 Fixed Focal Length 25.4 mm (35mm film equivalent) Aperture f/2.
If the device is not functioning properly, please contact the dealer you purchased this product from or Canon Service & Support at www.usa.canon.