TS700 series Online Manual English
Contents Using Online Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Symbols Used in This Document. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Touch-enabled Device Users (Windows). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Trademarks and Licenses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Basic Operation. . . . . .
Loading Paper in the Rear Tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Loading Paper in the Cassette. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Loading Envelopes in Rear Tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 Placing Multi-purpose Tray. . . . . . . . . . . . . . . . . . . . . . . . . .
Handling Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 Legal Restrictions on Printing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 Printer Handling Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 Transporting Your Printer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Feed settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208 Web service setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209 ECO settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210 Quiet setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printer Driver Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267 Quick Setup Tab Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268 Main Tab Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275 Page Setup Tab Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cannot Find Printer on Check Printer Settings Screen During Wired LAN Setup (Windows)Checking Printer's IP Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327 Cannot Find Printer on Check Printer Settings Screen During Wired LAN Setup (Windows)Checking Security Software Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Updating Printer Driver in Network Environment (Windows). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385 Errors and Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386 Four-Digit Alphanumeric Characters Appear on LCD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 387 When Error Occurred. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using Online Manual Operating Environment Symbols Used in This Document Touch-enabled Device Users (Windows) Printing Online Manual Trademarks and Licenses Screenshots in This Manual 9
Symbols Used in This Document Warning Instructions that, if ignored, could result in death, serious personal injury, or property damage caused by incorrect operation of the equipment. These must be observed for safe operation. Caution Instructions that, if ignored, could result in personal injury or property damage caused by incorrect operation of the equipment. These must be observed for safe operation.
Touch-enabled Device Users (Windows) For touch actions, you need to replace "right-click" in this document with the action set on the operating system. For example, if the action is set to "press and hold" on your operating system, replace "right-click" with "press and hold.
Trademarks and Licenses • Microsoft is a registered trademark of Microsoft Corporation. • Windows is a trademark or registered trademark of Microsoft Corporation in the U.S. and/or other countries. • Windows Vista is a trademark or registered trademark of Microsoft Corporation in the U.S. and/or other countries. • Internet Explorer is a trademark or registered trademark of Microsoft Corporation in the U.S. and/or other countries.
Apache License Version 2.0, January 2004 http://www.apache.org/licenses/ TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION 1. Definitions. "License" shall mean the terms and conditions for use, reproduction, and distribution as defined by Sections 1 through 9 of this document. "Licensor" shall mean the copyright owner or entity authorized by the copyright owner that is granting the License.
2. Grant of Copyright License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable copyright license to reproduce, prepare Derivative Works of, publicly display, publicly perform, sublicense, and distribute the Work and such Derivative Works in Source or Object form. 3. Grant of Patent License.
7. Disclaimer of Warranty. Unless required by applicable law or agreed to in writing, Licensor provides the Work (and each Contributor provides its Contributions) on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied, including, without limitation, any warranties or conditions of TITLE, NON-INFRINGEMENT, MERCHANTABILITY, or FITNESS FOR A PARTICULAR PURPOSE.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: * Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. * Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
Use is subject to license terms below. This distribution may include materials developed by third parties. Sun, Sun Microsystems, the Sun logo and Solaris are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other countries.
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ---- Part 6: Cisco/BUPTNIC copyright notice (BSD) ----Copyright (c) 2004, Cisco, Inc and Information Network Center of Beijing University of Posts and Telecommunications. All rights reserved.
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ---- Part 8: Apple Inc. copyright notice (BSD) ----Copyright (c) 2007 Apple Inc.
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. LEADTOOLS Copyright (C) 1991-2009 LEAD Technologies, Inc.
MIT License Copyright (c) 1998, 1999, 2000 Thai Open Source Software Center Ltd Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
CONCERNING THE MERCHANTABILITY OF THIS SOFTWARE OR ITS FITNESS FOR ANY PARTICULAR PURPOSE. (1) Red Hat Incorporated Copyright (c) 1994-2009 Red Hat, Inc. All rights reserved. This copyrighted material is made available to anyone wishing to use, modify, copy, or redistribute it subject to the terms and conditions of the BSD License.
The FreeType Project is distributed in several archive packages; some of them may contain, in addition to the FreeType font engine, various tools and contributions which rely on, or relate to, the FreeType Project. This license applies to all files found in such packages, and which do not fall under their own explicit license. The license affects thus the FreeType font engine, the test programs, documentation and makefiles, at the very least.
The FreeType Project is copyright (C) 1996-2000 by David Turner, Robert Wilhelm, and Werner Lemberg. All rights reserved except as specified below. 1. No Warranty -------------THE FREETYPE PROJECT IS PROVIDED `AS IS' WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Discusses general use and applications of FreeType, as well as future and wanted additions to the library and distribution. If you are looking for support, start in this list if you haven't found anything to help you in the documentation. o freetype-devel@nongnu.org Discusses bugs, as well as engine internals, design issues, specific licenses, porting, etc. Our home page can be found at http://www.freetype.org --- end of FTL.TXT --The TWAIN Toolkit is distributed as is.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
Basic Operation Printing Photos from a Computer Printing Photos from a Smartphone/Tablet Printing a Disc Label from a Computer 27
Printing Photos from a Computer This section describes how to print photos with Easy-PhotoPrint Editor. 1. Open paper support (A) and pull out paper support extension (B). 2. Open the feed slot cover (C). 3. Slide right paper guide (D) to open both paper guides. 4. Load photo paper in portrait orientation WITH PRINT SIDE FACING UP.
5. Slide right paper guide (D) to align with both sides of paper stack. 6. Close feed slot cover (C) gently. After closing the feed slot cover, the paper information registration screen for the rear tray appears on the LCD.
7. Press the OK button. 8. Use the button to select the size of the loaded paper on the rear tray, then press the OK button. Note • The (asterisk) on the LCD indicates the current setting. 9. Use the button to select the type of the loaded paper on the rear tray, then press the OK button. Follow the instructions of any messages displayed to register the paper information. 10. Pull out paper output tray (E) and extend paper output support (F).
From the Start menu, select (All apps >) Canon Utilities > Easy-PhotoPrint Editor. For macOS: From the Go menu in Finder, select Application and double-click the Canon Utilities folder, the EasyPhotoPrint Editor folder, and then the Easy-PhotoPrint Editor icon. 12. Click Photos icon (G). 13. Click Browse (H) in From computer: and select folder with photos you want to print. 14. Click photos (I) you want to print and select Open (J).
15. Specify number of copies and other options under Print Settings (K). For Windows: Specify the number of copies, your model name, the paper size, and other options. For macOS: Specify the number of copies, the paper size, and other options. Note • Selecting Same No. of each photo enables you to specify the number of copies for all photos with a single setting. • Selecting Same No. of each photo disables the number-of-copies setting specified for each photo.
Note • Easy-PhotoPrint Editor lets you easily create and print original collages, cards, or calendars using your favorite photos.
Printing Photos from a Smartphone/Tablet This section describes how to print photos with Canon PRINT Inkjet/SELPHY. For details on how to download Canon PRINT Inkjet/SELPHY, see below. Print Photos from Your Smartphone 1. Open paper support (A) and pull out paper support extension (B). 2. Open the feed slot cover (C). 3. Slide right paper guide (D) to open both paper guides. 4. Load photo paper in portrait orientation WITH PRINT SIDE FACING UP.
5. Slide right paper guide (D) to align with both sides of paper stack. 6. Close feed slot cover (C) gently. After closing the feed slot cover, the paper information registration screen for the rear tray appears on the LCD.
7. Press the OK button. 8. Use the button to select the size of the loaded paper on the rear tray, then press the OK button. Note • The 9. Use the (asterisk) on the LCD indicates the current setting. button to select the type of the loaded paper on the rear tray, then press the OK button. Follow the instructions of any messages displayed to register the paper information. 10. Pull out paper output tray (E) and extend paper output support (F).
The list of photos saved on your smartphone/tablet is displayed. 13. Select a photo. You can also select multiple photos at once. 14. Specify the number of copies, paper size, etc. 15. Select Print.
Printing a Disc Label from a Computer This section describes how to print photos on a printable disc with Easy-PhotoPrint Editor. Important • Do not mount the multi-purpose tray until the message prompting you to load the printable disc appears. Doing so can damage the printer. 1. Start Easy-PhotoPrint Editor. For Windows: The procedure below is for a computer running the Windows 10 operating system. From the Start menu, select (All apps >) Canon Utilities > Easy-PhotoPrint Editor.
5. Click Browse (E) in From computer: and select folder with photos you want to print. 6. Click photos (F) you want to print and select Open (G). 7. Edit disc label and select Next (H). You can change the background or add texts.
8. Specify number of copies and other options under Print Settings (I). For Windows: Specify the number of copies, your printer name, and other options. For macOS: Specify the number of copies and other options. 9. Start printing. For Windows: Click Print (J). For macOS: Click Next. When the Print dialog appears, specify your model name and other options, and then click Print.
10. When message prompting you to load printable disc appears on printer's LCD, remove cassette from printer and then detach multi-purpose tray from back of cassette. Insert the removed cassette back into the printer.
11. Push paper output tray (K) all the way in. 12. Place printable disc on multi-purpose tray. 1. WITH PRINT SIDE FACING UP, place printable disc, and press it against lock (L) at bottom. 2. While pressing down lock with printable disc, insert top of printable disc into slits (M).
13. Place multi-purpose tray on multi-purpose tray guide. 14. Insert multi-purpose tray straight in in horizontal direction until arrow ( purpose tray guide is approximately aligned with arrow ( ) on multi- ) on multi-purpose tray. 15. Press OK button on printer. The multi-purpose tray is drawn into the printer and printing will start. 16. After printing is complete, pull multi-purpose tray from printer to remove it.
17. While pressing down lock (L), take out printable disc from slits (M) on multi-purpose tray, and remove it. 18. Pull paper output tray (K) towards you until it aligns with operation panel (N). Note • Easy-PhotoPrint Editor enables you to print photos onto the disc label with various layouts.
Network Available Connection Methods The following connection methods are available on the printer. • Wireless Connection Connect the printer and devices (e.g. computer/smartphone/tablet) using a wireless router. If you have a wireless router, we recommend you use one for wireless connection. ◦ Connection methods vary depending on the wireless router type. ◦ You can change network settings such as the network name (SSID) and security protocol on the printer.
Note • You can connect the printer and computer using a USB cable (USB connection). Prepare a USB cable. For details, see Connects to Another Computer via LAN/Changes from USB to LAN Connection. Network Connection Settings/Setup Perform connection setup for the printer and computer/smartphone/tablet. For more on setup procedure, click here. Changing Network Settings See below for changing connection settings for the printer and computer/smartphone/tablet.
Notice/Restriction See below for details.
Restrictions When connecting another device while a device (such as a computer) is already connected to the printer, connect it using the same connection method as the connected device. If you connect using a different connection method, the connection to the device in use will be disabled. Connection Using a Wired Network cannot be performed on printers that do not support a wired connection. Connect via wireless router • You cannot establish a printer with wireless and wired connections at the same time.
• If you connect a device and the printer using Wireless Direct, Internet connection may become unavailable depending on your environment. In that case, web services for the printer cannot be used. • In Wireless Direct mode, you can connect up to five devices at the same time. If you try to connect a sixth device while five devices are already connected, an error will appear. If an error appears, disconnect a device that does not use the printer, then configure settings again.
Network Connection Tips Default Network Settings Detect Same Printer Name Connects to Another Computer via LAN/Changes from USB to LAN Connection Printing Network Settings Reconfiguration Method of LAN Connection/Reconfiguration Method of Wi-Fi Connection 50
Default Network Settings LAN Connection Defaults Item Default Change wireless/wired LAN Disable LAN Network name (SSID) BJNPSETUP Wi-Fi security Disable IP address (IPv4) Auto setup IP address (IPv6) Auto setup Set printer name* XXXXXXXXXXXX Enable/disable IPv6 Enable Enable/disable WSD Enable Timeout setting 15 minutes Enab./disab. Bonjour Enable Service name Canon TS700 series LPR setting Enable RAW protocol Enable LLMNR Enable PictBridge commun.
Confirm request Displayed *1 "ab" is specified at random and "XX" represents last two digits of printer's MAC address. (The value is specified when the printer is turned on for the first time.) *2 The password is specified automatically when the printer is turned on for the first time.
Detect Same Printer Name When the printer is detected during setup, plural printers with the same name may appear on the results screen. Select a printer with checking the printer settings against those on detection result screen. • For Windows: Check the printer's MAC address or serial to select the correct printer from the results. • For macOS: The printer names appear with the MAC address added at the end or as the printer name specified by Bonjour.
Connects to Another Computer via LAN/Changes from USB to LAN Connection To connect an additional computer to the printer via LAN, or to change from USB to LAN connection, perform setup from the web page. For Windows, you can perform setup using the Setup CD-ROM.
Printing Network Settings Use the operation panel to print the printer's current network settings. Important • The network settings printout contains important information about your network. Handle it with care. 1. Check that printer is turned on. 2. Load three sheets of A4 or Letter-sized plain paper. 3. Press Setup button. The Setup menu screen appears. 4. Select Device settings and press OK button. 5. Select LAN settings and press OK button. 6. Select Print LAN details and press OK button.
3-2-3 Frequency Frequency XX (GHz) 3-2-4 MAC Address MAC address XX:XX:XX:XX:XX:XX 3-2-5 Connection Connection status Active/Inactive 3-2-6 SSID SSID Wireless LAN network name (SSID) 3-2-7 Channel Channel XX (1 to 13) 3-2-8 Encryption Encryption method None/WEP/TKIP/AES 3-2-9 WEP Key Length WEP key length (bits) Inactive/128/64 3-2-10 Authentication Authentication method None/auto/open/shared/WPA-PSK/WPA2-PSK 3-2-11 TCP/IPv4 TCP/IPv4 Enable 3-2-12 IP Address IP address
3-2-26 Default Gateway1 Default gateway 1 XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX 3-2-27 Default Gateway2 Default gateway 2 XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX 3-2-28 Default Gateway3 Default gateway 3 XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX 3-2-29 Default Gateway4 Default gateway 4 XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX 3-2-33 IPsec IPsec setting Active 3-2-34 Security Protocol Security method ESP/ESP & AH/AH 3-3 Wireless Direct Operation mode for Wireless Direct Enable/Disa
4-1 MAC Address MAC address XX:XX:XX:XX:XX:XX 4-2 Connection Wired LAN status Active/Inactive 4-3 TCP/IPv4 TCP/IPv4 Enable 4-4 IP Address IP address XXX.XXX.XXX.XXX 4-5 Subnet Mask Subnet mask XXX.XXX.XXX.XXX 4-6 Default Gateway Default gateway XXX.XXX.XXX.
4-21 Default Gateway4 Default gateway 4 XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX 4-25 IPsec IPsec setting Active 4-26 Security Protocol Security method ESP/ESP & AH/AH 4-27 Wired LAN DRX Discontinuous reception (wired LAN) Enable/Disable 5 Other Settings Other settings – 5-1 Printer Name Printer name Printer name (Up to 15 alphanumeric characters) 5-2 Wireless Direct DevName Device name for wireless direct Device name for wireless direct (Up to 32 alphanumeric characters) 5-4 WSD
6 Bluetooth Bluetooth settings ― 6-1 Bluetooth Setting Bluetooth Enable/Disable 6-3 Bluetooth Device Address Bluetooth device address of the printer XXXXXXXX 6-5 Bluetooth Device Name Bluetooth device name of the printer XXXXXXXX 7 Printer Log Service Printer log service ― 7-1 Unsent Usage Logs Number of unsent usage logs 0 to 200 7-2 Usage Log Last Sent Last date when usage log was sent XXXXXXXX 7-3 Point Service Registration status Active/Awaiting Activation/No Active Service
Reconfiguration Method of LAN Connection/Reconfiguration Method of Wi-Fi Connection Reconfiguration Method of LAN Connection Reconfiguration Method of Wi-Fi Connection Reconfiguration Method of LAN Connection Follow either procedure below to change LAN connection method (wired or Wi-Fi). • For Windows: ◦ Redo setup using the Setup CD-ROM or from the web page. ◦ Enable Wi-Fi or wired LAN on the operation panel of the printer.
IJ Network Device Setup Utility (Windows) IJ Network Device Setup Utility Starting Up IJ Network Device Setup Utility Diagnosing and Repairing Network Settings Performing/Changing Network Settings List of Models Which Does Not Support Diagnosis and Repair Function List of Models Which Does Not Support IPv6 Configuration via USB Connection 62
IJ Network Device Setup Utility IJ Network Device Setup Utility allows you to diagnose or repair the network status, and to perform printer settings on network.
Starting Up IJ Network Device Setup Utility Start up IJ Network Device Setup Utility as shown below. • In Windows 10, select Start > (All apps > ) > Canon Utilities > IJ Network Device Setup Utility. • In Windows 8.1 or Windows 8, select IJ Network Device Setup Utility on the Start screen to start IJ Network Device Setup Utility. If IJ Network Device Setup Utility is not displayed on the Start screen, select the Search charm and search for "IJ Network Device Setup Utility".
Diagnosing and Repairing Network Settings IJ Network Device Setup Utility diagnoses and repairs computer settings or connection between the computer and printer when a problem (e.g. cannot print from a printer on the network) occurs. Important • Some models do not support diagnosis and repair function. For details: List of Models Which Does Not Support Diagnosis and Repair Function Follow the procedure below. 1. Start up IJ Network Device Setup Utility. 2. Check the displayed message and select Yes. 3.
Performing/Changing Network Settings Canon IJ Network Device Setup Utility Screen Performing Network Settings 66
Canon IJ Network Device Setup Utility Screen Items on Canon IJ Network Device Setup Utility Screen Menus on Canon IJ Network Device Setup Utility Screen Items on Canon IJ Network Device Setup Utility Screen Toolbar Items on Canon IJ Network Device Setup Utility Screen The screen below appears when you start up IJ Network Device Setup Utility and select Printer Network Setup. Detected printers are listed on the screen and the items below are shown.
Appears after performing network setup and clicking Set to close the window. • Requires Setup Indicates the printer is required to perform Wi-Fi setup. Performing/Changing Wi-Fi Settings • Not Set Indicates the printer cannot be used on network, or IPv6 is disabled. Specify an IP address or enable IPv6 on Network Settings.... Performing/Changing Wi-Fi Settings • IP Address Overlap Indicates the IP address is duplicated to another printer.
Appears if the printer is used by IP address specified automatically. • Manual Appears if the printer is used by IP address specified manually. Note • If USB is selected from the pulldown menu on the toolbar, "-" is displayed. H: MAC Address Displays the MAC address of the detected printer. Note • If USB is selected from the pulldown menu on the toolbar, "-" is displayed. I: Device Name Displays the printer device name if it is registered.
D: Help menu Help Menu Items on Canon IJ Network Device Setup Utility Screen Toolbar This section describes items on Canon IJ Network Device Setup Utility Screen toolbar. A: Perform wired or Wi-Fi setup. Note • This item has the same function as Network Settings... in the Printer Settings menu. B: Redetects printers. Note • This item has the same function as Update in the View menu. C: Stops detecting printers. Note • This item has the same function as Cancel in the View menu.
Performing Network Settings Performing/Changing Wired LAN Connection (Ethernet Cable) Settings Performing/Changing Wi-Fi Settings Assigning Printer Information 71
Performing/Changing Wired LAN Connection (Ethernet Cable) Settings Follow the procedure below to perform/change wired LAN settings. Note • For some models, you can perform network setup for a USB connected printer using IJ Network Device Setup Utility. Select USB on Switch View under the View menu to display printers for which you can perform setup. 1. Start up IJ Network Device Setup Utility. 2. Check the displayed message and select Yes. 3. Select Printer Network Setup on the displayed screen.
7. Perform/change settings. You can switch the screen between IPv4 and IPv6. Click the tab to switch the protocol. • IPv4 settings A: Use IPv4 address Always selected. (displayed in a gray out state) B: Get IP address automatically Select this option to use an IP address automatically assigned by a DHCP server. DHCP server functionality must be enabled on your router.
A: Use IPv6 address Select when you use the printer with IPv6 environment. B: Use Stateless Address: Select when you use an IP address assigned automatically. Use a router compatible with IPv6. Note • This setting item is not available depending on the printer you are using. C: Use Manual Address: Select this option if no DHCP server functionality is available in your setup where you use the printer, or you want to use a fixed IP address. Enter the IP address and IP address prefix length.
Performing/Changing Wi-Fi Settings Follow the procedure below to perform/change Wi-Fi settings. Important • Enable Easy wireless connect (Cableless setup) before performing printer setup. (Not required if you change the IP address.) For details, search for "NR049" on your printer's online manual and see the page shown. • If you use a printer over the Wi-Fi, we highly recommend you perform security settings for Wi-Fi network using WPA/WPA2 from the viewpoint of security.
Select Wi-Fi and click OK. 6. Enter password and click OK. The Network Settings screen appears. 7. Perform/change settings. You can switch the screen between IPv4 and IPv6. Click the tab to switch the protocol. • IPv4/IPv6 settings A: Network Type: Select the Wi-Fi mode. ◦ Infrastructure Connects the printer to the Wi-Fi with a wireless router. ◦ Direct Connects the printer to wireless communication devices (smartphone or tablet) without a wireless router.
The network name (SSID) for Wireless Direct appears while in Wireless Direct. C: Search... The Detected Wireless Routers screen is displayed to select a wireless router to connect to. For a wireless router already connected to the computer, Available is displayed on Communication Status. If you select a wireless router with Not Connected on Communication Status from the list, clicking Set displays the WPA/WPA2 or WEP setting screen for a wireless router.
Enter the IP address, subnet mask, and default gateway. • IPv6 settings Note • If you select a USB connected printer on step 4, you cannot perform IPv6 settings depending on the printer you are using. For details, see List of Models Which Does Not Support IPv6 Configuration via USB Connection. • The setting items below are available only when Infrastructure is selected for Network Type:. If Direct is selected, all items are displayed in a gray out status and you cannot perform any settings.
D: Use DHCPv6: Select when you obtain an IP address using DHCPv6. Note • This setting item is not available depending on the printer you are using. 8. Click Set.
Assigning Printer Information Follow the procedure below to assign/change printer location name or device name. The names appear on Device Name: and Location: on the Canon IJ Network Device Setup Utility screen. Note • If USB is selected from the pulldown menu on the toolbar, this setting item is not available. 1. Start up IJ Network Device Setup Utility. 2. Check the displayed message and select Yes. 3. Select Printer Network Setup on the displayed screen. Detected printers are listed. 4.
List of Models Which Does Not Support Diagnosis and Repair Function The following models does not support "Diagnose and Repair" function of IJ Network Device Setup Utility.
List of Models Which Does Not Support IPv6 Configuration via USB Connection For the following models, you can perform settings only for IPv4 using IJ Network Device Setup Utility. (You cannot perform settings for IPv6.
• TR9530 series 83
Handling Paper, Ink Tanks, Multi-purpose Tray, etc.
Loading Paper Paper Sources Loading Paper in the Rear Tray Loading Paper in the Cassette Loading Envelopes in Rear Tray 85
Paper Sources The printer has two paper sources for feeding paper, the rear tray (A) and cassette (B). You can load all supported paper on the rear tray. Supported Media Types You can load A4, B5, A5, or Letter-sized plain paper in the cassette. Note • When printing, select the correct page size and media type. If you select the wrong page size or media type, the printer may feed paper from the wrong paper source or may not print with the proper print quality.
Loading Paper in the Rear Tray You can load plain paper or photo paper. You can also load envelopes on the rear tray. Loading Envelopes in Rear Tray Important • If you cut plain paper to a size of 5" x 7" (13 x 18 cm) or smaller to perform a trial print, it may cause a paper jam. Note • We recommend Canon genuine photo paper for printing photos. For details on the Canon genuine paper, see Supported Media Types.
3. Open the feed slot cover (C). 4. Slide right paper guide (D) to open both paper guides. 5. Load paper stack in portrait orientation WITH PRINT SIDE FACING UP.
6. Slide right paper guide (D) to align with both sides of paper stack. Do not slide the paper guides too hard against the paper. The paper may not be fed properly. Important • Always load paper in portrait orientation (E). Loading paper in landscape orientation (F) can cause paper jams. Note • Do not load sheets of paper higher than the load limit mark (G).
7. Close feed slot cover (C) gently. Important • If the feed slot cover is open, paper cannot be fed. Be sure to close the feed slot cover. After closing the feed slot cover, the paper information registration screen for the rear tray appears on the LCD. 8. Press the OK button. 9. Use the button to select the size of the loaded paper on the rear tray, then press the OK button.
Note • The 10. Use the (asterisk) on the LCD indicates the current setting. button to select the type of the loaded paper on the rear tray, then press the OK button. Follow the instructions of any messages displayed to register the paper information. 11. Pull out paper output tray (H) and extend paper output support (I). Be sure to pull out the paper output tray before printing. If not, printing will not start.
Loading Paper in the Cassette You can load A4, B5, A5, or Letter-sized plain paper in the cassette. Note • In the cassette, be sure to load only plain paper. • You can use general copy paper or Canon Red Label Superior WOP111/Canon Océ Office Colour Paper SAT213. For the page size and paper weight you can use for this printer, see Supported Media Types. 1. Prepare paper. Align the edges of paper. If paper is curled, flatten it. Note • Align the edges of paper neatly before loading.
3. Remove the cassette cover (B). Lift the cassette cover straight up and remove it. 4. Slide paper guides (C) in front and (D) on right to open guides. 5. Load paper stack in portrait orientation WITH PRINT SIDE FACING DOWN, and place it in center of cassette. Important • Always load paper in portrait orientation (E). Loading paper in landscape orientation (F) can cause paper jams.
Note • Align the paper stack with the edge of the cassette as shown in the figure below. If the paper stack is in contact with the protrusion (G), the paper may not be fed properly. 6. Slide front paper guide (C) to align it with paper stack. Align paper guide with where it clicks into place. 7. Slide right paper guide (D) to align it with paper stack. Do not slide the paper guide too hard against the paper. The paper may not be fed properly.
Note • Do not load sheets of paper higher than the load limit mark (H). • Keep the paper stack height below the tabs (I) of the paper guides. 8. Mount cassette cover (B) and insert cassette into printer. Push the cassette into the printer until it stops. After inserting the cassette into the printer, the paper information registration screen for the cassette appears on the LCD.
9. Press the OK button. 10. Use the button to select the size of the loaded paper in the cassette, then press the OK button. Note • The (asterisk) on the LCD indicates the current setting. 11. Check media type and press OK button. Follow the instructions of any messages displayed to register the paper information. 12. Pull out paper output tray (J) and extend paper output support (K). Be sure to pull out the paper output tray before printing. If not, printing will not start.
Note • To prevent incorrect printing, this printer has a function that detects whether the settings for the paper loaded in the cassette matches the paper settings. Before printing, make print settings in accordance with the paper settings. When this function is enabled, an error message is displayed if these settings do not match to prevent incorrect printing. When this error message is displayed, check and correct the paper settings.
Loading Envelopes in Rear Tray You can load Envelope DL and Envelope Com 10 on the rear tray. The address is automatically rotated and printed according to the envelope's direction by specifying with the printer driver properly. Important • Printing from a PictBridge (Wi-Fi) compliant device is not supported. • Do not use the following envelopes. They could jam in the printer or cause the printer to malfunction.
3. Open the feed slot cover (C). 4. Slide right paper guide (D) to open both paper guides. 5. Load envelopes in portrait orientation WITH PRINT SIDE FACING UP. Up to 10 envelopes can be loaded at once. Fold flap of the envelope and load the envelope in portrait orientation with the address side facing up. 6. Slide right paper guide (D) to align with both sides of envelopes.
Do not slide the paper guides too hard against the envelopes. The envelopes may not be fed properly. Note • Do not load envelopes higher than the load limit mark (E). 7. Close feed slot cover (C) gently. Important • If the feed slot cover is open, paper cannot be fed. Be sure to close the feed slot cover.
After closing the feed slot cover, the paper information registration screen for the rear tray appears on the LCD. 8. Press the OK button. 9. Use button to select size of loaded envelopes on rear tray and press OK button. Note • The 10. Use (asterisk) on the LCD indicates the current setting. button to select Envelope and press OK button. Follow the instructions of any messages displayed to register the paper information. 11. Pull out paper output tray (F) and extend paper output support (G).
Note • To prevent incorrect printing, this printer has a function that detects whether the settings for the paper loaded on the rear tray matches the paper settings. Before printing, make print settings in accordance with the paper settings. When this function is enabled, an error message is displayed if these settings do not match to prevent incorrect printing. When this error message is displayed, check and correct the paper settings.
Placing Multi-purpose Tray Cautions When Printing with Multi-purpose Tray Placing a Printable Disc Placing Printable Nail Stickers How to Detach / Attach Multi-purpose Tray 103
Cautions When Printing with Multi-purpose Tray Cautions Common to using Multi-purpose Tray • Be sure to use the multi-purpose tray supplied with this printer. • Do not mount the multi-purpose tray while the printer is in operation. • Do not remove the multi-purpose tray while the printer is in operation. Doing so may damage the printer, the multi-purpose tray, or the media. • Do not get dirt on the multi-purpose tray or scratches on the reflectors.
Placing a Printable Disc Before Placing a Printable Disc Placing a Printable Disc Removing a Printable Disc 105
Before Placing a Printable Disc A printable disc differs from regular disc (BD/DVD/CD, etc.) in that its label surface has been specially processed or printing by an inkjet printer. The following items are needed to print onto the printable disc. • Multi-purpose tray (supplied with the printer) The multi-purpose tray is stored in the back of the cassette. • 4.72 in. (12 cm) printable disc Obtain a printable disc with a label surface compatible with inkjet printing.
Placing a Printable Disc To print onto a printable disc, place it on the supplied multi-purpose tray, and then insert it into the printer. Important • Do not mount the multi-purpose tray until the message prompting you to load the printable disc appears. Doing so can damage the printer. Note • If test printing is executed onto test printing paper, depending on the paper type, the printer may not be able to read its size correctly, preventing the border areas from being printed.
Note • After inserting the cassette into the printer, if a message appears on the screen, complete registration of paper information by pressing the OK button. 2. Push paper output tray (A) all the way in. 3. Place printable disc on multi-purpose tray. Important • Check that there is no dirt on the multi-purpose tray before placing a printable disc on it.
2. While pressing down lock with printable disc, insert top of printable disc into slits (D). 4. Place multi-purpose tray on multi-purpose tray guide. 5. Insert multi-purpose tray straight in in horizontal direction until arrow ( purpose tray guide is approximately aligned with arrow ( ) on multi- ) on multi-purpose tray. Important • Do not insert the multi-purpose tray beyond the arrow ( 109 ) on the multi-purpose tray guide.
Note • The multi-purpose tray may be ejected after a certain amount of time passes. In such a case, follow the on-screen instructions to place the multi-purpose tray again.
Removing a Printable Disc 1. Pull out multi-purpose tray. 2. While pressing down lock (A), take out printable disc from slits (B) on multi-purpose tray, and remove it. Important • Do not touch the printing surface when removing the disc from the multi-purpose tray. Note • Allow the printing surface to dry before removing the disc.
4. Store multi-purpose tray under cassette.
Placing Printable Nail Stickers Before Placing Printable Nail Stickers Placing Printable Nail Stickers Removing Printable Nail Stickers 113
Before Placing Printable Nail Stickers The following items are needed to print onto Printable Nail Stickers. • Multi-purpose tray (supplied with the printer) The multi-purpose tray is stored in the back of the cassette. • Printable Nail Stickers (NL-101) Note • For the latest information on Printable Nail Stickers, access our website.
Placing Printable Nail Stickers To print onto Printable Nail Stickers, place them on the multi-purpose tray supplied with the printer, and then insert them into the printer. Important • Do not mount the multi-purpose tray until the message prompting you to load Printable Nail Stickers appears. Doing so can damage the printer. 1. When message prompting you to load Printable Nail Stickers appears, detach multipurpose tray from back of cassette. Insert the removed cassette back into the printer.
2. Push paper output tray (A) all the way in. 3. Place Printable Nail Stickers on multi-purpose tray. Important • Check that there is no dirt on the multi-purpose tray before placing Printable Nail Stickers on it. • To prevent getting dirt or fingerprints on Printable Nail Stickers, hold the stickers by their edges. If the print side gets any dirt or is damaged, it may cause poor print quality.
2. While pressing down lock with Printable Nail Stickers, insert two tabs (D) on top into slits (E) on multi-purpose tray. 4. Place multi-purpose tray on multi-purpose tray guide. 5. Insert multi-purpose tray straight in in horizontal direction until arrow ( purpose tray guide is approximately aligned with arrow ( ) on multi- ) on multi-purpose tray. Important • Do not insert the multi-purpose tray beyond the arrow ( 117 ) on the multi-purpose tray guide.
Note • The multi-purpose tray may be ejected after a certain amount of time passes. In such a case, follow the on-screen instructions to place the multi-purpose tray again.
Removing Printable Nail Stickers 1. Pull out multi-purpose tray. 2. Remove Printable Nail Stickers. While pressing down lock (A), remove two tabs (B) on the top out of slits (C). Important • Do not touch the printing surface when removing Printable Nail Stickers. Note • Allow the printing surface to dry before removing Printable Nail Stickers. If you see printing on the multi-purpose tray or outside the Printable Nail Stickers, wipe them clean after the printing surface has dried. 3.
4. Pull paper output tray (D) towards you until it aligns with operation panel (E). Important • If the paper output tray is being pushed into the printer, the normal printing cannot be executable. Be sure to pull the paper output tray towards you until it aligns with the operation panel. 5. Store multi-purpose tray under cassette.
How to Detach / Attach Multi-purpose Tray Detaching Multi-purpose Tray 1. Take cassette out of printer and remove cassette cover. Be sure to remove any paper. 2. Turn cassette over and remove multi-purpose tray. Slide the multi-purpose tray, take it out of the six tabs (A), and then lift it. Important • Be sure to remove any orange shipping tape on the multi-purpose tray.
Attaching Multi-purpose Tray 1. Take cassette out of printer and remove cassette cover. Be sure to remove any paper. 2. Turn cassette over and attach multi-purpose tray to it. Turn the multi-purpose tray so that its underside faces up, align it with the six tabs (A) in the orientation shown in the figure below, and then slide to attach. Important • Insert the multi-purpose tray, making sure that its holes are aligned with the tabs on the back of the cassette.
Replacing Ink Tanks Replacing Ink Tanks Checking Ink Status on the LCD Ink Tips 123
Replacing Ink Tanks When remaining ink cautions or errors occur, the message will appear on the LCD to inform you of the error. In this state, the printer cannot print. Take appropriate action according to the message. An Error Occurs Note • If print results become faint or white streaks appear despite sufficient ink levels, see Maintenance Procedure. • For precautionary notes on handling ink tanks, see Notes on ink tanks.
Push the tab (A) and lift the ink tank to remove. Important • Do not touch other parts besides the ink tanks. • Handle the ink tank carefully to avoid staining of clothing or the surrounding area. • Discard the empty ink tank according to the local laws and regulations regarding disposal of consumables. Note • Do not remove two or more ink tanks at the same time. Be sure to replace ink tanks one by one when replacing two or more ink tanks. 4.
5. Hold the ink tank with the orange protective cap (E) pointing up while being careful not to block the Y-shape air hole (D). 6. Lift up the tab on the orange protective cap (E) to remove it off GENTLY. Important • Do not push the sides of the ink tank. If you push the sides of the ink tank with the Y-shape air hole (D) blocked, ink may splash. • Do not touch the inside of the orange protective cap (E) or the open ink port (F). The ink may stain your hands if you touch them.
8. Press on the top of the ink tank until the ink tank snaps firmly into place. Important • You cannot print if the ink tank is installed in the wrong position. Be sure to install the ink tank in the correct position according to the label on the print head holder. • You cannot print unless all the ink tanks are installed. Be sure to install all the ink tanks. 9. Close top cover.
Note • If the error message appears on the LCD after the top cover is closed, take appropriate action. An Error Occurs • When you start printing after replacing the ink tank, the printer starts cleaning the print head automatically. Do not perform any other operations until the printer completes the cleaning of the print head. • If the print head is out of alignment, as indicated by misaligned printed ruled lines or similar symptoms, align the print head. • The printer may make noise during operation.
Checking Ink Status on the LCD You can also check ink status on the LCD. A symbol appears in area A in case of any messages about the remaining ink level. Example: The ink is running low. Prepare a new ink tank. The resulting print quality may not be satisfactory, if printing is continued under this condition. Note • The above screen shows estimated ink levels. • You can also check the ink status on the computer screen.
Ink Tips How is ink used for various purposes other than printing? Ink may be used for purposes other than printing. When you use the Canon printer for the first time after you install the bundled ink tanks, the printer consumes a small amount of ink in the amount to enable printing by filling the nozzles of the Print Head with ink. For this reason, the number of sheets that can be printed with the first ink tanks is fewer than the succeeding ink tanks.
If Printing Is Faint or Uneven Maintenance Procedure Printing the Nozzle Check Pattern Examining the Nozzle Check Pattern Cleaning the Print Head Deep Print Head Cleaning Aligning the Print Head 131
Maintenance Procedure If print results are blurred, colors are not printed correctly, or print results are unsatisfactory (e.g. misaligned printed ruled lines), perform the maintenance procedure below. Important • Do not rinse or wipe the print head and ink tank. This can cause trouble with the print head and ink tank. Note • Make sure that the orange protective tape does not remain on the ink tank. • Check the ink status.
Step3 Clean the print head. From the printer Cleaning the Print Head From the computer • For Windows: Cleaning the Print Heads • For macOS: Cleaning the Print Heads After cleaning the print head, print and examine the nozzle check pattern: Step1 If the problem is not resolved after performing from step 1 to step 3 twice: Step4 Clean the print head deeply.
Adjusting Print Head Position 134
Printing the Nozzle Check Pattern Print the nozzle check pattern to determine whether the ink ejects properly from the print head nozzle. Note • If the remaining ink level is low, the nozzle check pattern will not be printed correctly. Replace the ink tank whose ink is low. You need to prepare: a sheet of A4 or Letter-sized plain paper 1. Check that printer is turned on. 2. Load a sheet of A4 or Letter-sized plain paper in the cassette. Loading Paper in the Cassette 3.
Examining the Nozzle Check Pattern Examine the nozzle check pattern, and clean the print head if necessary. 1. Check if there are missing lines in the pattern A or horizontal white streaks in the pattern B.
Cleaning the Print Head Clean the print head if lines are missing or if horizontal white streaks are present in the printed nozzle check pattern. Cleaning unclogs the nozzles and restores the print head condition. Cleaning the print head consumes ink, so clean the print head only when necessary. 1. Check that printer is turned on. 2. Press the Setup button, use the button to select Maintenance, and press the OK button. LCD and Operation Panel 3.
Deep Print Head Cleaning If print quality does not improve by the standard cleaning of the print head, clean the print head deeply. Cleaning the print head deeply consumes more ink than the standard cleaning of the print head, so clean the print head deeply only when necessary. 1. Check that printer is turned on. 2. Press the Setup button, use the button to select Maintenance, and press the OK button. LCD and Operation Panel 3. Use button to select Deep Cleaning and press OK button.
Aligning the Print Head If printed ruled lines are misaligned or print results are otherwise unsatisfactory, adjust the print head position. Note • If the remaining ink level is low, the print head alignment sheet will not be printed correctly. Replace the ink tank whose ink is low. • If ink runs out as the print head alignment sheet is printed, an error message appears on the LCD. An Error Occurs You need to prepare: two sheets of A4 or Letter-sized plain paper 1. Check that printer is turned on. 2.
Cleaning Cleaning Exterior Surfaces Cleaning Paper Feed Rollers Cleaning Inside the Printer (Bottom Plate Cleaning) Cleaning Cassette Pads 140
Cleaning Paper Feed Rollers If the paper feed roller is dirty or paper powder is attached to it, paper may not be fed properly. In this case, clean the paper feed roller. Cleaning will wear out the paper feed roller, so perform this only when necessary. You need to prepare: three sheets of A4 or Letter-sized plain paper 1. Check that printer is turned on. 2. Remove any paper from paper source to clean rollers. Note • If a message appears on the screen, check it and then press the OK button. 3.
Cleaning Inside the Printer (Bottom Plate Cleaning) Remove stains from the inside of the printer. If the inside of the printer becomes dirty, printed paper may get dirty, so we recommend performing cleaning regularly. You need to prepare: a sheet of A4 or Letter-sized plain paper* * Be sure to use a new piece of paper. 1. Make sure that the power is turned on, then remove any paper from the cassette. 2. Prepare paper. 1.
After inserting the cassette into the printer, the paper information registration screen is displayed on the LCD. Select A4 or Letter for Size:. 5. Pull out paper output tray (B) and extend paper output support (C). 3. Press the Setup button, use the button to select Maintenance, and press the OK button. LCD and Operation Panel 4. Use button to select Btm Plate Cleaning and press OK button. The paper cleans the inside of the printer as it feeds through the printer.
Note • When performing Bottom Plate Cleaning again, be sure to use a new piece of paper. If the problem is not resolved after performing cleaning again, the protrusions inside the printer may be stained. Wipe off any ink from the protrusions using a cotton swab or the like. Important • Before cleaning the printer, turn it off and unplug it.
Overview Safety Safety Precautions Regulatory Information WEEE (EU & EEA) Handling Precautions Canceling Print Jobs Legal Restrictions on Printing Printer Handling Precautions Transporting Your Printer When Repairing, Lending, or Disposing of the Printer Keeping Print Quality High Main Components and Their Use Main Components Power Supply LCD and Operation Panel Entering Numbers, Letters, and Symbols Changing Settings Changing Printer Settings from Your Computer (Windows) Changing Printer Settings from Your
Safety Safety Precautions Regulatory Information WEEE (EU&EEA) 146
Safety Precautions Safety Precautions • This manual contains important notices and safety precautions about your printer. Do not use the printer in ways other than described in the accompanying manuals, as this may result in fire, electric shock or other unexpected accidents. Safety standard marks and declarations are only valid for the supported voltages and frequencies in the applicable countries or regions. Warning • Users with cardiac pacemakers: This product emits a low-level magnetic flux.
• In case ink gets in contact with eyes, rinse with water immediately. In case ink gets in contact with skin, wash with soap and water immediately. If irritation to eyes or skin persists, obtain medical advice immediately. • Moving the printer • Do not hold the printer by the cassette. Hold the printer by its sides and carry it with both hands. General Notices Choosing a Location Refer to "Specifications" in the Online manual for details on operating environment.
Power Supply • Keep the area around the power outlet clear at all times so you can easily unplug the power cord if necessary. • Never remove the plug by pulling on the cord. General Notices • Do not tilt the printer, stand it on end, or turn it upside down. This may cause ink to leak. • Do not place anything on top of the printer. Be especially careful to avoid metal objects such as paper clips and staples, and containers holding flammable liquids such as alcohol or thinner.
Regulatory Information Users in the U.S.A. FCC Notice (U.S.A. Only) For 120V, 60Hz model Model Number: K10492 (Contains FCC Approved WLAN Module K30365, FCC Approved Bluetooth K30375) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Interference Do not use the printer around medical equipment or other electronic devices. Signals from the printer may interfere with the correct operation of these devices.
WEEE (EU&EEA) Only for European Union and EEA (Norway, Iceland and Liechtenstein) This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2012/19/EU) and national legislation. This product should be handed over to a designated collection point, e.g., on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (EEE).
Ce symbole indique que ce produit ne doit pas être jeté avec les ordures ménagères, conformément à la directive DEEE (2012/19/UE) et à la réglementation de votre pays. Ce produit doit être confié au distributeur à chaque fois que vous achetez un produit neuf similaire, ou à un point de collecte mis en place par les collectivités locales pour le recyclage des Déchets des Équipements Électriques et Électroniques (DEEE).
peligrosas que normalmente están asociadas con los RAEE. Al mismo tiempo, su cooperación a la hora de desechar correctamente este producto contribuirá a la utilización eficazde los recursos naturales. Para más información sobre cómo puede eliminar el equipo para su reciclado, póngase en contacto con las autoridades locales, con las autoridades encargadas de los desechos, con un sistema de gestión RAEE autorizado o con el servicio de recogida de basuras doméstico.
Apenas para a União Europeia e AEE (Noruega, Islândia e Liechtenstein) Este símbolo indica que o produto não deve ser colocado no lixo doméstico, de acordo com a Directiva REEE (2012/19/UE) e a legislação nacional. Este produto deverá ser colocado num ponto de recolha designado, por exemplo, num local próprio autorizado quando adquirir um produto semelhante novo ou num local de recolha autorizado para reciclar resíduos de equipamentos eléctricos e electrónicos (EEE).
Αυτό το σύμβολο υποδηλώνει ότι αυτό το προϊόν δεν πρέπει να απορρίπτεται μαζί με τα οικιακά απορρίμματα, σύμφωνα με την Οδηγία σχετικά με τα Απόβλητα Ηλεκτρικού και Ηλεκτρονικού Εξοπλισμού (ΑΗΗΕ) (2012/19/ΕΕ) και την εθνική σας νομοθεσία. Αυτό το προϊόν πρέπει να παραδίδεται σε καθορισμένο σημείο συλλογής, π.χ. σε μια εξουσιοδοτημένη βάση ανταλλαγής όταν αγοράζετε ένα νέο παρόμοιο προϊόν ή σε μια εξουσιοδοτημένη θέση συλλογής για την ανακύκλωση των αποβλήτων Ηλεκτρικού και Ηλεκτρονικού Εξοπλισμού (ΗΗΕ).
kierrätysjärjestelmän ylläpitäjältä ja jätehuoltoyhtiöltä. Lisätietoja sähkö- ja elektroniikkalaiteromun keräyksestä ja kierrätyksestä on osoitteessa www.canon-europe.com/weee. Endast för Europeiska unionen och EES (Norge, Island och Liechtenstein) Den här symbolen visar att produkten enligt WEEE-direktivet (2012/19/EU) och nationell lagstiftning inte får sorteras och slängas som hushållsavfall. Den här produkten ska lämnas in på en därför avsedd insamlingsplats, t.ex.
Ez a szimbólum azt jelzi, hogy a helyi törvények és a WEEE-irányelv (2012/19/EU) szerint a termék nem kezelhető háztartási hulladékként. A terméket a kijelölt nyilvános gyűjtőpontokon kell leadni, például hasonló cserekészülék vásárlásakor, illetve bármelyik, elektromos és elektronikai berendezésekből származó hulladék (WEEE) átvételére feljogosított gyűjtőponton.
k účinnému využívaniu prírodných zdrojov. Ďalšie informácie o mieste recyklácie opotrebovaných zariadení získate od miestneho úradu, úradu životného prostredia, zo schváleného plánu OEEZ alebo od spoločnosti, ktorá zaisťuje likvidáciu komunálneho odpadu. Viac informácií nájdete aj na webovej stránke: www.canon-europe.com/weee.
elektros ir elektroninės įrangos (EEĮ) atliekų perdirbimo punktą. Netinkamas tokios rūšies atliekų tvarkymas dėl elektros ir elektroninėje įrangoje esančių pavojingų medžiagų gali pakenkti aplinkai ir žmonių sveikatai. Padėdami užtikrinti tinkamą šio gaminio šalinimo tvarką, kartu prisidėsite prie veiksmingo gamtos išteklių naudojimo.
Doar pentru Uniunea Europeană şi EEA (Norvegia, Islanda şi Liechtenstein) Acest simbol indică faptul că acest produs nu trebuie aruncat o dată cu reziduurile menajere, în conformitate cu Directiva DEEE (Directiva privind deşeurile de echipamente electrice şi electronice) (2012/19/UE) şi legile naţionale.
vrstom otpada može da ima moguće negativne posledice po životnu sredinu i ljudsko zdravlje usled potencijalno opasnih materijala koji se uglavnom vezuju za EEE. U isto vreme, vaša saradnja na ispravnom odlaganju ovog proizvoda će doprineti efikasnom korišćenju prirodnih resursa. Za više informacija o tome gde možete da predate vašu staru opremu radi recikliranje, vas molimo, da kontaktirate lokalne gradske vlasti, komunalne službe, odobreni plan reciklaže ili Gradsku čistoću.
Handling Precautions Canceling Print Jobs Legal Restrictions on Printing Printer Handling Precautions Transporting Your Printer When Repairing, Lending, or Disposing of the Printer Keeping Print Quality High 163
Legal Restrictions on Printing Printing or modifying printed copies of the following may be punishable under law. This list is non-exhaustive. When in doubt, check with a local legal representative.
Printer Handling Precautions Do not place any object on the top cover! Do not place any object on the top cover. It will fall into the rear tray when the top cover is opened and cause the printer to malfunction. Also, place the printer where objects will not fall on it.
Transporting Your Printer When relocating the printer for changing your living place or repairing it, make sure of the following. Important • Pack the printer in a sturdy box so that it is placed with its bottom facing down, using sufficient protective material to ensure safe transport. • With the print head and ink tank left installed in the printer, press the ON button to turn off the power. This allows the printer to automatically cap the print head, thus preventing it from drying.
Important • We recommend to hold and carry out this printer as shown in the figure below. If you hold the cassette, it may fall out of the printer.
When Repairing, Lending, or Disposing of the Printer If you have entered personal data, passwords and/or other security settings on the printer, such information may be stored in the printer. When sending the printer for repair, lending or transferring the printer to another person, or disposing of the printer, please be sure to follow the steps below in order to delete such information and prevent third parties from accessing it.
Keeping Print Quality High The key to printing with the optimal printing quality is to prevent the print head from drying or clogging. Always observe the following rules for optimal printing quality. Note • Depending on the type of paper, ink may blur if you trace the printed area with a highlight pen or paintstick, or bleed if water or sweat comes in contact with the printed area.
Main Components and Their Use Main Components Power Supply LCD and Operation Panel Entering Numbers, Letters, and Symbols 170
Main Components Front View Rear View Inside View Operation Panel 171
Front View A: Paper Support Open to load paper in the rear tray. B: Paper Support Extension Extend to load paper in the rear tray. C: Feed Slot Cover Prevents anything from falling into the feed slot. Open it to slide the paper guides, and close it before printing. D: Rear Tray Load paper here. Two or more sheets of the same size and type of paper can be loaded at the same time, and fed automatically one sheet at a time.
I: Cassette Load A4, B5, A5, or Letter-sized plain paper into the cassette, and insert it into the printer. Loading Paper in the Cassette J: Paper Output Tray Printed paper is ejected. Pull out it before printing. When using the multi-purpose tray to print, insert the paper output tray all the way in by following the message. K: Paper Output Support Extend to support ejected paper. L: Multi-purpose Tray Guide Place the multi-purpose tray here.
Rear View A: USB Port Plug in the USB cable to connect the printer with a computer. B: Wired LAN Connector Plug in the LAN cable to connect the printer to a LAN. C: Power Cord Connector Plug in the supplied power cord. D: Transport Unit Cover Open when removing jammed paper. E: Rear Cover Detach when removing jammed paper. Important • Do not touch the metal casing. • Do not plug in or unplug the USB cable or LAN cable while the printer is printing with the computer. This can cause trouble.
Inside View A: Top Cover Open to replace an ink tank or to remove jammed paper inside the printer. B: Print Head Holder The print head is pre-installed. Note • For details on replacing an ink tank, see Replacing Ink Tanks.
Operation Panel A: Wireless connect button To set wireless router information in the printer directly from a smartphone or other such device (without having to do any procedures at the router), hold down this button. B: LCD (Liquid Crystal Display) Displays messages, menu items, and the operational status. C: Setup button Displays the Setup menu screen. With this menu, you can perform printer maintenance and change printer settings. Also used for selecting the input mode.
Power Supply Checking that Power Is On Turning the Printer On and Off Checking the Power Plug/Power Cord Unplugging the Printer 177
Checking that Power Is On The ON lamp is lit when the printer is turned on. Even if the LCD is off, if the ON lamp is lit, the printer is on. Note • It may take a while for the printer to start printing immediately after you turn on the printer. • The LCD will turn off if the printer is not operated for about 10 minutes. To restore the display, press any button or perform the print operation.
Turning the Printer On and Off Turning on the printer 1. Press the ON button to turn on the printer. The ON lamp flashes and then remains lit. Confirming that the Power Is On Note • It may take a while for the printer to start printing immediately after you turn on the printer. • If an error message is displayed on the LCD, see An Error Occurs. • You can set the printer to automatically turn on when a print operation is performed from a computer connected by USB cable or via network.
Important • When you unplug the power cord after turning off the printer, be sure to confirm that the ON lamp is off. Note • You can set the printer to automatically turn off when no operations are performed or no print jobs are sent to the printer for a certain interval. This feature is set to on by default.
Checking the Power Plug/Power Cord Unplug the power cord once a month to confirm that the power plug/power cord does not have anything unusual described below. • The power plug/power cord is hot. • The power plug/power cord is rusty. • The power plug/power cord is bent. • The power plug/power cord is worn. • The power plug/power cord is split. Caution • If you find anything unusual with the power plug/power cord described above, unplug the power cord and call for service.
Unplugging the Printer To unplug the power cord, follow the procedure below. Important • When you unplug the power cord, press the ON button, then confirm that the ON lamp is off. Unplugging the power cord while the ON lamp is lit or flashing may cause drying or clogging of the print head and print quality may be reduced. 1. Press the ON button to turn the printer off. 2. Confirm that the ON lamp is off. 3. Unplug the power cord.
LCD and Operation Panel Pressing the Setup button (A) on the operation panel displays the Setup menu screen, which enables you to perform printer settings and maintenance. Selecting a Menu or Setting Item In a menu screen or settings screen, use the the OK button (C) to proceed with the procedure. button (B) to select an item or option, and then press To return to the previous screen, press the Back button (D). Example: Changing the setting for Prevent Abrasion. 1. Press Setup button (A). 2.
If the icon appears on the LCD, it indicates that Wi-Fi is enabled and the printer is connected to the wireless router. Depending on the signal state, the icon will change. Signal strength: 81 % or more You can use the printer over Wi-Fi without any problems. Signal strength: 51 % or more The problem such as the printer cannot print may occur according to the network status. We recommend placing the printer near the wireless router.
Entering Numbers, Letters, and Symbols The buttons on the operation panel allow you to enter (or change) characters, numbers, or symbols when setting up the network or making other settings. Switching the Input Mode The current input mode appears at the upper right corner of the LCD. Pressing the Setup button on the operation panel toggles through the input modes in the order lowercase > uppercase > numeric > symbols, showing the first available character.
Changing Settings Changing Printer Settings from Your Computer (Windows) Changing Printer Settings from Your Computer (macOS) Changing Settings from Operation Panel 186
Changing Printer Settings from Your Computer (Windows) Changing the Print Options Registering a Frequently Used Printing Profile Setting the Ink Tank to be Used Managing the Printer Power Changing the Printer Operation Mode 187
Changing the Print Options You can change the detailed printer driver settings for print data that is sent from an application software. Check this check box if part of the image data is cut off, the paper source during printing differs from the driver settings, or printing fails. 1. Open the printer driver setup window 2. Click Print Options... on the Page Setup tab The Print Options dialog box opens. 3. Change the individual settings If necessary, change the setting of each item, and then click OK.
Registering a Frequently Used Printing Profile You can register the frequently used printing profile to Commonly Used Settings on the Quick Setup tab. Unnecessary printing profiles can be deleted at any time. Registering a Printing Profile 1. Open the printer driver setup window 2. Set the necessary items From Commonly Used Settings on the Quick Setup tab, select the printing profile to be used and if necessary, change the settings after Additional Features.
Quick Setup tab. The name and icon are displayed in Commonly Used Settings. Important • To save the page size, orientation, and number of copies that was set in each sheet, click Options..., and check each item. Note • When you re-install the printer driver or upgrade the printer driver version, the print settings that are already registered will be deleted from Commonly Used Settings. Registered print settings cannot be saved and preserved. If a profile is deleted, register the print settings again.
Setting the Ink Tank to be Used This feature enables you to specify the most appropriate ink tank among installed ink tanks according to an intended use. 1. Open the printer driver setup window 2. Click Print Options... on the Page Setup tab The Print Options dialog box appears. 3. Select the ink tank to be used from Print With Select the ink tank to be used for printing and click OK. 4. Click OK on the Page Setup tab When you perform printing, the specified ink tank will be used.
Managing the Printer Power This function allows you to manage the printer power from the Canon IJ Printer Assistant Tool. Power Off The Power Off function turns off the printer. When you use this function, you will not be able to turn the printer on from the Canon IJ Printer Assistant Tool. 1. Open Canon IJ Printer Assistant Tool 2. Execute power off Click Power Off. When the confirmation message appears, click OK. The printer power switches off.
Click OK. When the confirmation message appears, click OK. The setting is enabled after this. When you want to disable this function, select Disable from the list according to the same procedure. Note • When the printer is turned off, the Canon IJ Status Monitor message varies depending on the Auto Power On setting. When the setting is Enable, "Printer is standing by" is displayed. When the setting is Disable, "Printer is offline" is displayed.
Changing the Printer Operation Mode If necessary, switch between various modes of printer operation. Custom Settings 1. Open the Canon IJ Printer Assistant Tool 2. Check that the printer is on and then click Custom Settings The Custom Settings dialog box opens. Note • If the printer is off or if communication between the printer and the computer is disabled, an error message may appear because the computer cannot collect the printer status.
Rotate 90 degrees left when orientation is [Landscape] On the Page Setup tab, you can change the rotation direction of the Landscape in the Orientation. To rotate the print data 90 degrees to the left during printing, select this item. To rotate the print data 90 degrees to the right during printing, clear this item. Important • Do not change this setting while the print job is displayed in the print wait list. Otherwise, characters may be omitted or the layout may become corrupt.
Changing Settings from Operation Panel Changing Settings from Operation Panel Setting Items on Operation Panel Print settings LAN settings Bluetooth settings PictBridge settings Other dev.
Changing Settings from Operation Panel This section describes the procedure to change the settings in the Device settings screen, taking the steps to specify Prevent abrasion as an example. Note • The (asterisk) on the LCD indicates the current setting. 1. Check that printer is turned on. 2. Press the Setup button. The Setup menu screen is displayed. 3. Select Device settings and then press the OK button. The Device settings screen is displayed. 4.
Setting Items on Operation Panel Items for Printer Other device settings Language selection Web service setup ECO settings Quiet setting Items for Paper/Printing Print settings Bluetooth settings PictBridge settings Feed settings Items for Maintenance/Management LAN settings Firmware update Reset setting System information 198
Print settings Select this menu from Device settings in Setup menu. • Prevent abrasion Use this setting only if the print surface becomes smudged. Important • Be sure to set this back to OFF after printing since it may result in lower printing speed or lower print quality. • Amount of extension Select the amount of image that extends off the paper when performing Borderless Printing.
LAN settings Select this menu from Device settings in Setup menu. Wi-Fi Wireless Direct Wired LAN Print LAN details Wi-Fi • Wi-Fi enab./disable Enables or disables Wi-Fi. • Wi-Fi setup Selects the setup method for Wi-Fi connection. Note • You can also enter this setting menu by selecting Wi-Fi setup from the Setup menu screen.
Wireless Direct • Switch WL Direct Enables/disables Wireless Direct. • Change name (SSID) Changes the identifier (SSID/the printer's name displayed on a Wi-Fi Direct compatible device) for Wireless Direct. • Change password Changes the password for Wireless Direct. • Confirm request Set whether the printer displays the confirmation screen when a Wi-Fi Direct compatible device is connecting the printer. • Manual setup For details on each setting item: Manual setup Wired LAN • Enab./dis.
Note • You cannot use the same printer name as that already used for other LAN connected devices. • You cannot use a hyphen for the initial or last character of the printer name. • TCP/IP settings Performs IPv4 or IPv6 setting. • WSD setting Setting items when you use WSD (one of the network protocols supported in Windows). ◦ Enable/disable WSD Selects whether WSD is enabled or disabled. Note • When this setting is enabled, the printer icon is displayed on the Network Explorer in Windows.
Setting items for printing from a PictBridge (Wi-Fi) compliant device. ◦ Enable/disable Selecting Enable allows you to print from a PictBridge (Wi-Fi) compliant device. ◦ Timeout setting Specifies the timeout length. • DRX setting Selecting Enable allows you to activate discontinuous reception when the printer is connected to a device compatible with wired LAN. • IPsec settings Selecting Enable allows you to specify the IPsec settings.
Other dev. settings Select this menu from Device settings in Setup menu. • Key repeat Selecting ON lets you quickly display candidate numbers or characters by holding down the during character entry.
Language selection Changes the language for LCD messages and menus.
Firmware update Select this menu from Device settings in Setup menu. You can update the firmware of the printer, check the firmware version, or perform settings of a notification screen. Important • When you use this function, make sure the printer is connected to the internet. Note • Only Current version is available when Disable is selected for Wi-Fi enab./disable of Wi-Fi and also for Enab./dis. wired LAN of Wired LAN in LAN settings. • Install update Performs the firmware update of the printer.
Reset setting Select this menu from Device settings in Setup menu. Returns all settings you made to the printer back to the default. However, some data may not be changed, depending on the current usage state of your printer. Important • Depending on the setting item, it is necessary to perform connection or setup again after you have returned the setting back to the default. • Web service setup Returns the Web service settings back to the default.
Feed settings Select this menu from Setup menu. By registering the paper size and the media type loaded on the rear tray or in the cassette, you can prevent the printer from misprinting by displaying the message before printing starts when the paper size or the media type of the loaded paper differs from the print settings. For details: Paper Settings • Save paper info Registers the paper size and the media type you load on the rear tray and in the cassette.
Web service setup Select this menu from Setup menu. • Connection setup The following setting items are available. ◦ GoogleCloudPrint Registers/Deletes the printer to/from Google Cloud Print. • DNS server setup Performs settings for a DNS server. Select Auto setup or Manual setup. If you select Manual setup, follow the display on the LCD to perform settings. • Proxy server setup Performs settings for a proxy server. Select Use or Do not use.
ECO settings This setting allows you to turn on/off the printer automatically to save electricity. Turning off Printer Automatically Turning on Printer Automatically Turning off Printer Automatically You can enable the printer to turn off automatically when no operation is made or no printing data is sent to the printer for a specified period of time. 1. Check that printer is turned on. 2. Press the Setup button. The Setup menu screen is displayed. 3. Select ECO settings and then press the OK button. 4.
Quiet setting Enables this function on the printer if you want to reduce the operating noise, such as when printing at night. Follow the procedure below to perform setting. 1. Check that printer is turned on. 2. Press the Setup button. The Setup menu screen is displayed. 3. Select Quiet mode and then press the OK button. 4. Select ON or OFF and press OK button. When ON is selected, you can reduce the operating noise while printing is in progress.
System information Select this menu from Setup menu. • Current version Displays the current firmware version. • Printer name Displays the printer name currently specified. • Serial number Displays the printer serial number.
Specifications General Specifications Printing resolution (dpi) 4800* (horizontal) x 1200 (vertical) * Ink droplets can be placed with a pitch of 1/4800 inch at minimum. Interface USB Port: Hi-Speed USB * Network Port: Wired LAN: 100BASE-TX / 10BASE-T Wi-Fi: IEEE802.11n / IEEE802.11g / IEEE802.11b * A computer that complies with Hi-Speed USB standard is required. Since the Hi-Speed USB interface is fully upwardly compatible with USB 1.1, it can be used at USB 1.1.
◦ Other sizes: 0.14 in. (3.4 mm) * For printable area of envelope, see below. Envelopes Auto duplex printing: • Top margin: 0.20 in. (5.0 mm) • Bottom margin: 0.20 in. (5.0 mm) • Left margin: ◦ Letter: 0.26 in. (6.4 mm) ◦ Other sizes: 0.14 in. (3.4 mm) • Right margin: ◦ Letter: 0.25 in. (6.3 mm) ◦ Other sizes: 0.14 in. (3.
Network Specifications Communication protocol TCP/IP Wired LAN Supported Standards: IEEE802.3u (100BASE-TX) / IEEE802.3 (10BASE-T) Transfer speed: 10 M/100 Mbps (auto switching) Wi-Fi Supported Standards: IEEE802.11n / IEEE802.11g / IEEE802.11b Frequency bandwidth: 2.4 GHz Channel: 1-11 or 1-13 * Frequency bandwidth and available channels differ depending on country or region. Communication distance: Indoors 164 feet/50 m * Effective range varies depending on the installation environment and location.
macOS Operating System OS X 10.10.5 - OS X 10.11, macOS 10.12 - macOS 10.13 Hard Disk Space 1.0 GB or more Note: For bundled software installation. The necessary amount of hard disk space may be changed without notice. Display XGA 1024 x 768 Other Supported OS iOS, Android, Windows 10 Mobile Some functions may not be available with the supported OS. Refer to the Canon web site for details.
Information about Paper Supported Media Types Paper Load Limit Unsupported Media Types Handling Paper Print Area 217
Supported Media Types For best results, choose paper designed for how you are printing. A variety of paper for documents as well as photos or illustrations is available from Canon. Use genuine Canon paper to print important photos, when possible. Media Types Genuine Canon paper Note • For warnings on use of the non-printable side, see each product's usage information. • Page sizes and media types differ depending on the country or region where the paper is sold.
Paper other than genuine Canon paper • Plain Paper (including recycled paper) • Envelopes*1 • T-Shirt Transfers*1 • Greeting Card*1 • Card Stock*1 *1 Printing to this paper from a PictBridge (Wi-Fi) compliant device is not supported. *2 When printing, mount a special adapter on the supplied multi-purpose tray.
• Hagaki 2 • Envelope Com 10 • Envelope DL • Nagagata 3 • Nagagata 4 • Yougata 4 • Yougata 6 • Card 2.17"x3.58" Special sizes Special page sizes must be within the following limits: • rear tray ◦ Minimum size: 2.17 x 3.51 in. (55.0 x 89.0 mm) Maximum size: 8.50 x 26.61 in. (215.9 x 676.0 mm) • cassette ◦ Minimum size: 5.83 x 8.27 in. (148.0 x 210.0 mm) Maximum size: 8.50 x 11.69 in. (215.9 x 297.0 mm) Paper Weight You can use paper in the following weight range.
Paper Load Limit This section shows the paper load limits of the rear tray, the cassette, and the paper output tray. Paper Load Limits of Rear Tray and Cassette Paper Load Limit of Paper Output Tray Note • Page sizes and media types differ depending on the country or region where the paper is sold. For details on page sizes and media types, access the Canon website. Paper Load Limits of Rear Tray and Cassette Genuine Canon Paper Paper for printing documents: Media Name
Paper other than Genuine Canon Paper Common Name Rear Tray Cassette Plain Paper (including recycled paper)*1 Approx. 100 sheets (Legal: 10 sheets) Approx. 250 sheets Envelopes 10 envelopes N/A T-Shirt Transfers A4: 1 sheet N/A Greeting Card Letter, 7"x10"(18x25cm): 1 sheet N/A Card Stock A4, Letter: 1 sheet N/A *1 Normal feeding at maximum capacity may not be possible with some types of paper, or under very high or low temperature or humidity.
Unsupported Media Types Do not use the following types of paper. Using such paper will cause not only unsatisfactory results, but also the printer to jam or malfunction.
Handling Paper • Be careful not to rub or scratch the surfaces of any types of paper when handling. • Hold the paper as closely as possible to its edges and try not to touch the printing surface. The print quality may be degraded if the printing surface is smudged with sweat or oil that comes from your hands. • Do not touch the printed surface until the ink is dried. Even when the ink is dried, be careful not to touch the printed surface as much as possible when handling.
Printing Printing from Computer Printing from Smartphone/Tablet Printing from Digital Camera Paper Settings 225
Printing from Computer Printing from Application Software (Windows Printer Driver) Printing from Application Software (macOS AirPrint) Printing Using Canon Application Software Printing Using a Web Service 226
Printing from Application Software (Windows Printer Driver) Basic Printing Setup Basic Various Printing Methods Changing the Print Quality and Correcting Image Data Overview of the Printer Driver Printer Driver Description Updating the Printer Driver 227
Basic Printing Setup This section describes settings on the Quick Setup tab used for basic printing. Basic Printing Setup 1. Check that printer is turned on 2. Load paper in printer 3. Open printer driver's setup screen 4. Select frequently used settings On the Quick Setup tab, use Commonly Used Settings to select from predefined print settings. When you select a print setting, the settings for Additional Features, Media Type, and Printer Paper Size automatically switch to the predefined values. 5.
Important • The print quality selections will differ depending on which print setting you select. 6. Select paper source For Paper Source, select Automatically Select, Rear Tray, or Cassette, whichever matches your purpose. Important • The paper source settings that can be selected may differ depending on the paper type and size.
7. Click OK The printer will now print using these settings. Important • When you select Always Print with Current Settings, the settings on the Quick Setup, Main, and Page Setup tabs are saved, and those settings are used in subsequent printings. • To register the current settings as a new preset, click Save... under Commonly Used Settings. Note • If the paper settings in the printer driver differ from the paper information registered on the printer, an error may occur.
From Paper Source, check the setting or select a new paper source. The current printer settings appear in Media Type and Page Size. 4. Apply settings To apply the printer settings to the printer driver, click Set. Note • If the Type on the printer is set to IJ Hagaki, Hagaki K, or Hagaki, or if the Page size on the printer is set to 2L/5"x7", click Set to display the dialog box. Select the media type and paper size that match your purpose, and then click OK.
Paper Settings on the Printer Driver and the Printer (Media Type) When you use this printer, selecting a media type and paper size that matches the print purpose will help you achieve the best print results. You can use the following media types on this printer. Canon genuine papers (Document Printing) Media name
Commercially available papers Media name Media Type in the printer driver Paper information registered on the printer Plain Paper (including recycled paper) Plain Paper Plain paper Envelopes Envelope Envelope T-Shirt Transfers T-Shirt Transfers Others Greeting Cards Inkjet Greeting Card Others Card Stock Card Stock Card stock 233
Paper Settings on the Printer Driver and the Printer (Paper Size) When you use this printer, selecting a paper size that matches the print purpose will help you achieve the best print results. You can use the following paper sizes on this printer. Printer Paper Size in the printer driver Cassette paper information registered on the printer Letter 8.5"x11" 22x28cm Letter Legal 8.
Custom Size Others 235
Various Printing Methods Setting a Page Size and Orientation Setting the Number of Copies and Printing Order Execute Borderless Printing Scaled Printing Page Layout Printing Tiling/Poster Printing Duplex Printing Setting Up Envelope Printing Printing on Postcards 236
Setting a Page Size and Orientation The paper size and orientation are essentially determined by the application software. When the page size and orientation set for Page Size and Orientation on the Page Setup tab are same as those set with the application software, you do not need to select them on the Page Setup tab.
Setting the Number of Copies and Printing Order You can also set the number of copies on the Quick Setup tab. 1. Open the printer driver setup window 2. Specify the number of copies to be printed For Copies on the Page Setup tab, specify the number of copies to be printed. 3. Specify the print order Check the Print from Last Page check box when you want to print from the last page in order, and uncheck the check box when you want to print from the first page.
• Print from Last Page: /Collate: • Print from Last Page: /Collate: 4. Click OK When you execute print, the specified number of copies will be printed with the specified printing order. Important • When the application software that you used to create the document has the same function, specify the settings on the printer driver. However, if the print results are not acceptable, specify the function settings on the application software.
Execute Borderless Printing The borderless printing function allows you to print data without any margin by enlarging the data so that it extends slightly off the paper. In standard printing, margins are created around the document area. However, in borderless printing function, these margins are not created. When you want to print data such as a photo without providing any margin around it, set borderless printing. You can also set borderless printing in Additional Features on the Quick Setup tab.
Click OK when the confirmation message appears. When a message prompting you to change the media type appears, select a media type from the list and click OK. 3. Check the paper size Check the Page Size list. When you want to change it, select another page size from the list. The list displays only sizes that can be used for borderless printing. 4. Adjust the amount of extension from the paper If necessary, adjust the amount of extension using the Amount of Extension slider.
Expanding the Range of the Document to Print Setting a large amount of extension allows you to perform borderless printing with no problems. However, the portion of the document extending off the paper range will not be printed and for this reason, the subjects around the perimeter of a photo may not be printed. When you are not satisfied with the result of borderless printing, reduce the amount of extension. The extension amount decreases as the Amount of Extension slider is moved to the left.
Scaled Printing 1. Open the printer driver setup window 2. Set scaled printing Select Scaled from the Page Layout list on the Page Setup tab. 3. Select the paper size of the document Using Page Size, select the page size that is set with your application software. 4. Set the scaling rate by using one of the following methods: • Select a Printer Paper Size When the printer paper size is smaller than the Page Size, the page image will be reduced.
• Specify a scaling factor Directly type in a value into the Scaling box. The current settings are displayed in the settings preview on the left side of the printer driver. 5. Click OK When you execute print, the document will be printed with the specified scale. Important • When the application software which you used to create the original has the scaled printing function, configure the settings on your application software. You do not need to configure the same setting in the printer driver.
Note • Selecting Scaled changes the printable area of the document.
Page Layout Printing The page layout printing function allows you to print more than one page image on a single sheet of paper. 1. Open the printer driver setup window 2. Set page layout printing Select Page Layout from the Page Layout list on the Page Setup tab. The current settings are displayed in the settings preview on the left side of the printer driver. 3. Select the print paper size Select the size of the paper loaded in the printer from the Printer Paper Size list. 4.
Page Layout To change the number of pages to be printed on a single sheet of paper, select the number of pages from the list. Page Order To change the page arrangement order, select a placement method from the list. Page Border To print a page border around each document page, check this check box. 5. Complete the setup Click OK on the Page Setup tab. When you execute print, the specified number of pages will be arranged on each sheet of paper in the specified order.
Tiling/Poster Printing The tiling/poster printing function allows you to enlarge image data, divide it into several pages, and print these pages on separate sheets of paper. You can also paste the pages together to create a large print like a poster. Setting Tiling/Poster Printing 1. Open the printer driver setup window 2. Set tiling/poster printing Select Tiling/Poster from the Page Layout list on the Page Setup tab.
4. Set the number of image divisions and the pages to be printed If necessary, click Specify..., specify the following settings in the Tiling/Poster Printing dialog box, and then click OK. Image Divisions Select the number of divisions (vertical x horizontal). As the number of divisions increases, the number of sheets used for printing increases. If you are pasting pages together to create a poster, increasing the number of divisions allows you to create a larger poster.
In the settings preview on the left of the Page Setup tab, click the pages that do not need to be printed. The pages that were clicked are deleted, and only the pages to be printed are displayed. Note • Click the deleted pages to display them again. • Right-click the settings preview to select Print all pages or Delete all pages. 2. Complete the setup After completing the page selection, click OK. When you execute print, only specified pages will be printed.
Duplex Printing You can also set duplex printing in Additional Features on the Quick Setup tab. Performing Automatic Duplex Printing You can perform the duplex printing without having to turn over the paper. 1. Open the printer driver setup window 2. Set automatic duplex printing Check the Duplex Printing check box on the Page Setup tab and confirm that Automatic is checked. 3. Select the layout Select Normal-size, Fit-to-Page, Scaled, or Page Layout from the Page Layout list. 4.
When you perform duplex printing, the print area of the document becomes slightly narrower than usual and the document may not fit on one page. Click Print Area Setup..., select one of the following process methods, and then click OK. Use normal-size printing Print without reducing the page. Use reduced printing Reduce the page slightly during printing. 5. Specify the side to be stapled The best Stapling Side is selected automatically from the Orientation and Page Layout settings.
3. Select the layout Select Normal-size, Fit-to-Page, Scaled, or Page Layout from the Page Layout list. 4. Specify the side to be stapled The best Stapling Side is selected automatically from the Orientation and Page Layout settings. To change the setting, select another stapling side from the list. 5. Set the margin width If necessary, click Specify Margin... and set the margin width, and then click OK. 6. Complete the setup Click OK on the Page Setup tab.
• After printing the front page, there is an ink drying wait time before starting to print the back page (Operation stops temporarily). Do not touch the paper during this time. You can change the ink drying wait time at Custom Settings in the Canon IJ Printer Assistant Tool. • When you use the automatic duplex printing function to print a postcard, print the address side first and then print the message side.
Setting Up Envelope Printing 1. Load envelope on the printer 2. Open the printer driver setup window 3. Select the media type Select Envelope from Commonly Used Settings on the Quick Setup tab. 4. Select the paper size When the Envelope Size Setting dialog box is displayed, select Envelope Com 10, Envelope DL, Yougata 4 4.13"x9.25", or Yougata 6 3.86"x7.48", and then click OK. 5. Set the orientation To print the addressee horizontally, select Landscape for Orientation.
6. Select the print quality Select High or Standard that matches your purpose for Print Quality. 7. Click OK When you execute print, the information is printed on the envelope. Important • When you execute envelope printing, guide messages are displayed. To hide the guide messages, check the Do not show this message again check box. To show the guide again, click the View Printer Status button on the Maintenance tab, and start the Canon IJ Status Monitor.
Printing on Postcards 1. Load postcard on the printer 2. Open the printer driver setup window 3. Select commonly used settings Display the Quick Setup tab, and for Commonly Used Settings, select Standard. 4. Select the media type For Media Type, select Ink Jet Hagaki (A), Ink Jet Hagaki, Hagaki K (A), Hagaki K, Hagaki (A), or Hagaki. Important • This printer cannot print on postcards that have photos or stickers attached.
7. Select the print quality For Print Quality, select High or Standard, according to your purpose. 8. Click OK When you execute printing, the data will be printed onto the postcard. Important • If you want to display a guide message when performing postcard printing, open the Maintenance tab and click View Printer Status to start the Canon IJ Status Monitor. On the Option menu, choose Display Guide Message and click Hagaki Printing to enable the setting.
Overview of the Printer Driver Canon IJ Printer Driver Opening Printer Driver's Setup Screen Canon IJ Status Monitor Checking Ink Status from Your Computer Instructions for Use (Printer Driver) 259
Canon IJ Printer Driver The Canon IJ printer driver (simply called printer driver below) is software that you install onto your computer so that it can communicate with the printer. The printer driver converts the print data created by your application software into data that your printer can understand, and sends the converted data to the printer. Because different printers support different data formats, you need a printer driver that supports your printer.
Opening Printer Driver's Setup Screen You can display the printer driver's setup screen from your application software or by clicking the printer icon. Displaying the Printer Driver's Setup Screen from Your Application Software Perform this procedure to set up the print settings during printing. 1. Select print command from application software The Print command can generally be found in the File menu. 2.
Canon IJ Status Monitor The Canon IJ Status Monitor is an application software that shows the status of the printer and the progress of printing. You will know the status of the printer with graphics, icons, and messages. Launching the Canon IJ Status Monitor The Canon IJ Status Monitor launches automatically when print data is sent to the printer. When launched, the Canon IJ Status Monitor appears as a button on the task bar. Click the button of the status monitor displayed on the task bar.
In such cases, take the appropriate action as described.
Checking Ink Status from Your Computer You can check the remaining ink level and the ink tank types for your model. 1. Open the printer driver setup window 2. Launching the Canon IJ Status Monitor On the Maintenance tab, click View Printer Status. 3. Display Estimated ink levels Ink status is displayed as an illustration. Note • The information displayed on the Canon IJ Status Monitor may differ depending on the country or region where you are using your printer.
Instructions for Use (Printer Driver) This printer driver is subject to the following restrictions. Keep the following points in mind when using the printer driver. Restrictions on the Printer Driver • Depending on the document type to be printed, the paper feed method specified in the printer driver may not operate correctly. If this happens, open the printer driver setup window from the Print dialog box of the application software, and check the setting in the Paper Source field on the Main tab.
3. 4. 5. 6. 7. Set the Page Layout that you want, and then click OK to close the window. Without starting printing, close the Print dialog box. Open Word's Print dialog box again. Open the printer driver setup window and click OK. Start printing. • If bitmap printing is enabled in Adobe Illustrator (Adobe Systems Incorporated), printing may take time or some data may not be printed. Print after unchecking the Bitmap Printing check box in the Print dialog box.
Printer Driver Description Quick Setup Tab Description Main Tab Description Page Setup Tab Description Maintenance Tab Description Canon IJ Status Monitor Description 267
Quick Setup Tab Description The Quick Setup tab is for registering commonly used print settings. When you select a registered setting, the printer automatically switches to the preset items. Commonly Used Settings The names and icons of frequently used printing profiles are registered. When you select a printing profile according to the purpose of the document, settings that match the purpose are applied.
Paper Saving Select this setting to save paper when printing a general document. The 2-on-1 Printing and Duplex Printing check boxes are checked automatically. If Page Size, Orientation, and Copies were set from the application software, those settings have priority. Envelope If you select this setting for printing an envelope, Media Type is set automatically to Envelope. In the Envelope Size Setting dialog box, select the size of the envelope to be used.
2-on-1 Printing Prints two pages of the document, side by side, on one sheet of paper. To change the page sequence, click the Page Setup tab, select Page Layout for Page Layout, and click Specify.... Then in the Page Layout Printing dialog box that appears, specify the Page Order. 4-on-1 Printing Prints four pages of the document, side by side, on one sheet of paper. To change the page sequence, click the Page Setup tab, select Page Layout for Page Layout, and click Specify....
Orientation Selects the printing orientation. If the application used to create your document has a similar function, select the same orientation that you selected in that application. Portrait Prints the document so that its top and bottom positions are unchanged relative to the paper feed direction. This is the default setting. Landscape Prints the document by rotating it 90 degrees relative to the paper feed direction.
Always Print with Current Settings Prints documents with the current settings starting from the next print execution. When you select this function and then close the printer driver setup window, the information that you set on the Quick Setup, Main, and Page Setup tabs are saved and printing with the same settings is possible starting from the next print execution.
Save the orientation setting Saves the Orientation to the printing profile in Commonly Used Settings. To apply the saved print orientation when the printing profile is selected, check this check box. If this check box is unchecked, the print orientation is not saved, and consequently the Orientation setting is not applied when the printing profile is selected. Instead the printer prints with the print orientation specified with the application software.
Switching the Paper Source to Match the Purpose Displaying the Print Results Before Printing Setting Paper Dimensions (Custom Size) Printing a Color Document in Monochrome Specifying Color Correction Adjusting Color Balance Adjusting Brightness Adjusting Contrast Registering a Frequently Used Printing Profile 274
Main Tab Description The Main tab allows you to create a basic print setup in accordance with the media type. Unless special printing is required, normal printing can be performed just by setting the items on this tab. Settings Preview The paper illustration shows how the original will be laid out on a sheet of paper. You can check an overall image of the layout. The printer illustration shows how to load paper to match the printer driver settings.
Print Quality Selects your desired printing quality. Select one of the following to set the print quality level that is appropriate for the purpose. Important • Depending on the Media Type settings, the same print results may be produced even if the Print Quality is changed. High Gives priority to print quality over printing speed. Standard Prints with average speed and quality. Draft This setting is appropriate for test printing.
Custom dialog box Set the quality level, and select the desired print quality. Quality You can use the slider bar to adjust the print quality level. Important • Certain print quality levels cannot be selected depending on the settings of Media Type. Note • The High, Standard, or Draft print quality modes are linked with the slider bar. Therefore when the slider bar is moved, the corresponding quality and value are displayed on the left.
Contrast Adjusts the contrast between light and dark in the image to be printed. Moving the slider to the right increases the contrast, moving the slider to the left decreases the contrast. You can also directly enter a value linked to the slider. Enter a value in the range from -50 to 50. Matching Tab Allows you to select the method for adjusting colors to match the type of document to be printed.
Page Setup Tab Description The Page Setup tab allows you to determine how a document is to be arranged on the paper. Also, this tab allows you to set the number of copies and the order of printing. If the application which created the document has a similar function, set them with the application. Settings Preview The paper illustration shows how the original will be laid out on a sheet of paper. You can check an overall image of the layout.
To rotate the document 90 degrees to the left when printing, select the Rotate 90 degrees left when orientation is [Landscape] check box. Rotate 180 degrees Prints the document by rotating it 180 degrees against the paper feed direction. The width of print area and the amount of extension that are configured in other application software will be reversed vertically and horizontally. Printer Paper Size Selects the size of paper actually loaded into the printer.
Page Layout Multiple pages of document can be printed on one sheet of paper. Specify... Opens the Page Layout Printing dialog box. Click this button to set details on page layout printing. Tiling/Poster This function enables you to enlarge the image data and divide the enlarged data into several pages to be printed. You can also glue together these sheets of paper to create large printed matter, such as a poster. Specify... Opens the Tiling/Poster Printing dialog box.
Important • If the application used to create your document has a similar function, specify the number of copies with the application without specifying it here. Print from Last Page Check this check box when you want to print from the last page in order. If you do this, you do not need to sort the pages into their correct order after printing. Uncheck this check box to print your document in normal order, starting from the first page.
Preview Icon Shows the settings made on the Page Layout Printing dialog box. You can check what the print result will look like before you actually print the data. Page Layout Specifies the number of document pages to fit on one sheet. Page Order Specifies the document orientation to be printed on a sheet of paper. Page Border Prints a page border line around each document page. Check this check box to print the page border line.
Booklet Printing dialog box This dialog box allows you to set how to bind the document as a booklet. Printing only on one side and printing a page border, can also be set in this dialog box. The settings specified in this dialog box can be confirmed in the settings preview on the printer driver. Preview Icon Shows the settings made on the Booklet Printing dialog box. You can check what the document will look like when printed as a booklet.
Print Options dialog box Makes changes to print data that is sent to the printer. Depending on the environment, this function may not be available. Disable ICM required from the application software Disables the ICM function required from the application software. When an application software uses Windows ICM to print data, unexpected colors may be produced or the printing speed may decrease. If these problems occur, checking this check box may resolve the problems.
Print after creating print data by page The print data is created in page units, and printing starts after the processing of one page of print data is complete. If a printed document contains unintended results such as streaks, selecting this check box may improve the results. Important • Uncheck this check box under normal circumstances. Prevention of Print Data Loss You can reduce the size of the print data that was created with the application software and then print the data.
Define Stamp... Opens the Stamp Settings dialog box. You can check the details of a selected stamp or save a new stamp. Place stamp over text Sets how the stamp is to be printed over the document. Check the Stamp check box to enable this. Check this check box to print a stamp over the printed document page. The printed data may be hidden behind the stamp. Uncheck this check box to print the document data over the stamp. The printed data will not be hidden behind the stamp.
For Date/Time/User Name, the creation date/time and user name of the printed object are displayed in Stamp Text. Important • Stamp Text appears grayed out and is unavailable if Date/Time/User Name is selected. TrueType Font Selects the font for the stamp text string. Style Selects the font style for the stamp text string. Size Selects the font size for the stamp text string. Outline Selects a frame that encloses the stamp text string.
Position Specifies the stamp position on the page. Selecting Custom from the list allows you to enter values for the X-Position and Y-Position coordinates directly. Rotation Specifies the angle of rotation for the stamp. The angle can be set by entering the number of degrees. Negative values rotate the stamp clockwise. Note • Rotation is enabled only when Text or Date/Time/User Name is selected for Stamp Type on the Stamp tab.
Select File... Opens the dialog box to open a file. Click this button to select a bitmap file (.bmp) to be used as the background. Layout Method Specifies how the background image is to be placed on the paper. When Custom is selected, you can set coordinates for X-Position and Y-Position. Intensity Adjusts the intensity of the bitmap to be used as a background. Moving the slider to the right increases the intensity, and moving the slider to the left decreases the intensity.
Maintenance Tab Description The Maintenance tab allows you to start the Canon IJ Printer Assistant Tool or check the status of the printer. Maintenance and Preferences Canon IJ Printer Assistant Tool is started. You can perform printer maintenance or change the settings of the printer. View Printer Status Starts the Canon IJ Status Monitor. Perform this function when you want to check the printer status and how a print job is proceeding. About Opens the About dialog box.
Important • If the font for displaying the language of your choice is not installed in your system, the characters will be garbled.
Canon IJ Status Monitor Description The Canon IJ Status Monitor displays the printer status and the printing progress. The printer status is shown by the images, icons, and messages in the status monitor. Features of the Canon IJ Status Monitor The Canon IJ Status Monitor has the following functions: Onscreen display of printer status The status monitor displays the printer status in real-time. You can check the progress of each document to be printed (print job).
: There is a notice about something other than a warning or an error. : There has been an error which requires a service. Ink Tank If a low ink warning or an empty ink tank error occurs, the status monitor displays an icon. The status monitor also uses images to display the estimated ink levels of the ink tanks. Move the cursor onto the image to check detailed information such as the remaining ink levels and the names of ink tanks that the printer can use. Document Name Name of the document being printed.
Display Warning Automatically When a Low Ink Warning Occurs Starts the Canon IJ Status Monitor window automatically and displays it in front of the other windows when a low ink warning occurs. Start when Windows is Started Automatically starts the Canon IJ Status Monitor when Windows is started. Remote UI menu You are able to open the printer's Remote User Interface. You are able to check the printer status and run maintenance functions on the printer when connected to and using it through a network.
Installing the Printer Driver You can access our web site through the Internet and download the latest printer driver for your model. 1. Turn off the printer 2. Start the installer Double-click the icon of the downloaded file. The installation program starts. Important • A confirmation/warning dialog box may appear when starting, installing or uninstalling software. This dialog box appears when administrative rights are required to perform a task.
Printing Using Canon Application Software Easy-PhotoPrint Editor Guide 297
Printing from Smartphone/Tablet Printing from iPhone/iPad/iPod touch (iOS) Printing from Smartphone/Tablet (Android) Printing from Windows 10 Mobile Device Printing with Wireless Direct 298
Printing with Wireless Direct You can connect devices (e.g. computer, smartphone, or tablet) to the printer by two methods below. • Wireless connection (connecting devices via a wireless router) • Direct wireless connection (connecting devices using Wireless Direct) This section describes Wireless Direct, which allows you to print by connecting the devices to the printer directly. Follow the procedure below to use Wireless Direct. 1. Preparing the printer. Changing Printer Setting to Use Wireless Direct 2.
The Wireless Direct is enabled and a device can be connected to the printer wirelessly. Note • You can check the following on the Wireless router info screen. Use the an item you want to check and then press the OK button. button to select • Network name(SSID): Identifier • Security protocol: Security setting and password • WL Direct dev. name: Printer name displayed on a Wi-Fi Direct compatible device The password is required when connecting a device to the printer.
Printing with Wireless Direct After connecting a device and the printer, start printing from the application of your device. Note • For more on printing from a device via Wi-Fi, refer to the device's or application's instruction manual. • You can print from your smartphone or tablet by installing Canon PRINT Inkjet/SELPHY. Download it from App Store and Google Play. For iOS For Android Changing Wireless Direct Setting Change the settings for the Wireless Direct following the procedure below. 1.
Change password • Manual setup 1. Select Manual setup and then press the OK button. 2. Press OK button and enter new password. 3. Select Yes and press OK button. • Auto update 1. Select Auto update and then press the OK button. 2. Select Yes and then press the OK button. 3. Select Done and then press the OK button. If you select Security protocol instead of Done, you can check the updated password.
Paper Settings By registering the paper size and the media type loaded on the rear tray or in the cassette, you can prevent the printer from misprinting by displaying the message before printing starts when the paper size or the media type of the loaded paper differs from the print settings. Note • The default setting is different between when you print from Smartphone/tablet, when you print from Windows, and when you print from macOS.
• When you insert the cassette: The screen to register the cassette paper information is displayed. Register the page size according to the paper loaded in the cassette. * You can load only plain paper in the cassette.
When you start printing, Size or type of loaded paper is different from the settings appears on the LCD. When you press the OK button, the screen for selecting the processing method is displayed. Please choose one of the following. Note • Depending on the setting, the choices below may not be displayed. Print on set paper Select if you want to print on the paper loaded without changing the paper settings.
To change the setting: Feed settings • When you print from Windows: The message which prevents misprinting is disabled by default. To change the setting: Changing the Printer Operation Mode • When you print from macOS: The message which prevents misprinting is enabled by default.
Frequently Asked Questions Network Cannot Find Printer on Network Cannot Find Printer while Using Wi-Fi Network Key (Password) Unknown Cannot Print or Connect For other questions about network, click here.
Cannot Print from Smartphone/Tablet Cannot Set Correctly (Network) Cannot Find Printer on Check Printer Settings Screen During Setup (Windows) Cannot Find Printer while Using Wi-Fi Cannot Find Printer while Using Wired LAN Printer Suddenly Stopped Working for Some Reason Network Key (Password) Unknown Forgot Administrator Password of Printer Printer Cannot Be Used After Replacing Wireless Router or Changed Router Settings Message Appears on Computer During Setup Checking Network Information Restoring to Fac
Network Settings and Common Problems Here are frequently asked questions on network. Select a connection method you are using, or you want to use.
Printing from Smartphone/Tablet Connecting Printer and Wireless Router Using Easy wireless connect Cannot Connect Smartphone/Tablet to Wireless Router Checking Wireless Router Network Name (SSID) for Smartphone/Tablet Setting Up Using Smartphone/Tablet Cannot Print from Smartphone/Tablet Cannot Find Printer from Smartphone/Tablet while Using Bluetooth Downloading Canon PRINT Inkjet/SELPHY Problems while Using Printer Message Appears on Computer During Setup Printer Prints Slowly No Ink Level Appears in Prin
Detect Same Printer Name Cannot Print or Connect Printer Suddenly Stopped Working for Some Reason Cannot Print or Connect LAN Setting Tips/Changing LAN Settings Forgot Administrator Password of Printer Checking Network Information Restoring to Factory Defaults Default Network Settings Connects to Another Computer via LAN/Changes from USB to LAN Connection Printing Network Settings Reconfiguration Method of LAN Connection/Reconfiguration Method of Wi-Fi Connection Checking Status Code Problems while Using Pr
Network Communication Problems Cannot Find Printer on Network Network Connection Problems Other Network Problems 312
Cannot Find Printer on Network While performing printer setup: Cannot Find Printer on Check Printer Settings Screen During Setup (Windows) Cannot Proceed beyond Printer Connection Screen While using printer: Cannot Find Printer while Using Wi-Fi Note • You cannot use the wireless LAN and the wired LAN at the same time.
Cannot Find Printer on Check Printer Settings Screen During Setup (Windows) If the printer cannot be found and the Check Printer Settings screen appears after searching the printer by Automatic search on the Search for Printers screen during driver setup, click Redetect and search for the printer again by the IP address on the Search for Printers screen. If the printer has not been found after searching it by the IP address, check network settings.
Cannot Find Printer on Check Printer Settings Screen During Wired LAN Setup (Windows)Checking Security Software Settings Cannot Find Printer on Check Printer Settings Screen During Wired LAN Setup (Windows)Checking Router Settings 315
Cannot Find Printer on Check Printer Settings Screen During Wi-Fi Setup (Windows)-Checking Power Status Are printer and network device (router, etc.) turned on? Make sure the printer is turned on. Checking that Power Is On Make sure network device (router, etc.) is turned on. If printer or network device is off: Turn on printer or network device. It may take a while for the printer and network device to become ready for use once they are turned on.
Cannot Find Printer on Check Printer Settings Screen During Wi-Fi Setup (Windows)-Checking PC Network Connection Can you view any web pages on your computer? Make sure the computer and network device (router, etc.) are configured and the computer is connected to the network. If you cannot view any web pages: Click Cancel on the Check Printer Settings screen to cancel to set up the network communication. After that, configure the computer and network device.
Cannot Find Printer on Check Printer Settings Screen During Wi-Fi Setup (Windows)-Checking Printer's Wi-Fi Settings Is printer set to allow wireless communication? Make sure the or icon is displayed on the LCD. If icon is not displayed: The printer is not set to allow wireless communication. Turn on wireless communication on the printer.
Cannot Find Printer on Check Printer Settings Screen During Wi-Fi Setup (Windows)-Checking Wi-Fi Environment Is the printer connected to the wireless router? Use the icon on the LCD to make sure the printer is connected to the wireless router. If is displayed: • Check wireless router configuration. After checking the wireless router setting, make sure the printer is not placed far away from the wireless router. The printer can be up to 50 m (164 ft) from the wireless router indoors.
For details, see the instruction manual supplied with the wireless router or contact the manufacturer. After taking measures above, click Redetect on the Check Printer Settings screen to redetect the printer. If the printer is found, follow the instructions on the screen to continue to set up network communication. If the printer cannot be detected, the printer is not connected to the wireless router. Connect the printer to the wireless router.
Cannot Find Printer on Check Printer Settings Screen During Wi-Fi Setup (Windows)-Checking Printer's IP Address Is printer's IP address specified correctly? If printer's IP address is not specified correctly, the printer may not be found. Make sure whether printer's IP address is not used for another device. To check the printer's IP address, print out the network settings information.
Cannot Find Printer on Check Printer Settings Screen During Wi-Fi Setup (Windows)-Checking Security Software Settings Disable block in firewall function temporarily. The firewall of your security software or operation system for computer may limit communication between the printer and your computer. Check the firewall setting of your security software or operation system or the message shown on your computer and disable block temporarily.
Cannot Find Printer on Check Printer Settings Screen During Wi-Fi Setup (Windows)-Checking Wireless Router Settings Check wireless router settings. Check wireless router network connection settings, such as IP address filtering, MAC address filtering, encryption key, and DHCP function. Make sure the same radio channel is assigned to the printer and the wireless router. To check the settings of the wireless router, see the instruction manual supplied with the wireless router or contact the manufacturer.
Cannot Find Printer on Check Printer Settings Screen During Wired LAN Setup (Windows)-Checking LAN Cable and Router Is LAN cable connected, and are printer and router on? Make sure the LAN cable is connected. Make sure the printer is turned on. Checking that Power Is On Make sure the router is turned on. If LAN cable is connected and printer or network device is off: Turn on printer or network device. It may take a while for the printer and network device to become ready for use once they are turned on.
Cannot Find Printer on Check Printer Settings Screen During Wired LAN Setup (Windows)-Checking PC Network Connection Can you view any web pages on your computer? Make sure the computer and network device (router, etc.) are configured and the computer is connected to the network. If you cannot view any web pages: Click Cancel on the Check Printer Settings screen to cancel to set up the network communication. After that, configure the computer and network device.
Cannot Find Printer on Check Printer Settings Screen During Wired LAN Setup (Windows)-Checking Printer's Wired LAN Settings Is printer set to allow wired communication? Make sure the icon is displayed on the LCD. If icon is not displayed: The printer is not set to allow wired communication. Turn on wired communication on the printer. Once you have turned on wired communication, redo the network communication setup from the beginning.
Cannot Find Printer on Check Printer Settings Screen During Wired LAN Setup (Windows)-Checking Printer's IP Address Is printer's IP address specified correctly? If printer's IP address is not specified correctly, the printer may not be found. Make sure whether printer's IP address is not used for another device. To check the printer's IP address, print out the network settings information.
Cannot Find Printer on Check Printer Settings Screen During Wired LAN Setup (Windows)-Checking Security Software Settings Disable block in firewall function temporarily. The firewall of your security software or operation system for computer may limit communication between the printer and your computer. Check the firewall setting of your security software or operation system or the message shown on your computer and disable block temporarily.
Cannot Find Printer on Check Printer Settings Screen During Wired LAN Setup (Windows)-Checking Router Settings Check router settings. Check router network connection settings such as IP address filtering, MAC address filtering, and DHCP function. For more on checking the settings of the router, refer to the instruction manual supplied with the router or contact its manufacturer. After checking the router settings, click Redetect on the Check Printer Settings screen to redetect the printer.
Cannot Proceed beyond Printer Connection Screen If you cannot proceed beyond the Printer Connection screen, check the following. Check1 Make sure USB cable is securely plugged in to printer and computer. Connect the printer and the computer using a USB cable as the illustration below. The USB port is located at the back of the printer. Important • Connect the "Type-B" terminal to the printer with the notched side facing UP. For details, refer to the instruction manual supplied with the USB cable.
3. Click Exit on Start Setup screen and finish setup. 4. Turn off printer. 5. Restart computer. 6. Make sure you have no application software running. 7. Perform setup on top page of Online Manual. Note • You can use the Setup CD-ROM to redo setup. • For macOS: 1. Click Next. The screen telling you that installation has not been completed appears. 2. Click No. The screen to select application software to install appears. 3. Click Back to Top. 4. Click Exit on Start Setup screen. 5. Turn off printer. 6.
Cannot Find Printer while Using Wi-Fi Make sure printer is turned on. Check1 If not, make sure the printer is securely plugged in and press ON button to turn on. The ON lamp flashes while the printer is initializing. Wait until the ON lamp stops flashing and remains lit. Check the Check2 The icon on LCD. icon appears by pressing the Setup button. If the icon is not displayed, select Enable for Wi-Fi enab./disable in Wi-Fi under LAN settings under Device settings from the setup menu.
Note • Use 2.4 GHz frequency band to connect to a wireless router. Match the network name (SSID) set for the printer with that for 2.4 GHz frequency band of the wireless router. To check the network name (SSID) set for the printer, print out the network setting information. Printing Network Settings Note • IJ Network Device Setup Utility allows you to diagnose and repair the network status. Select the link below to download IJ Network Device Setup Utility and install it.
• For Windows: Starting Up IJ Network Device Setup Utility • For macOS: Starting Up IJ Network Device Setup Utility Check7 Make sure the computer is connected to the wireless router. For more on how to check the computer settings or connection status, see your computer instruction manual or contact its manufacturer. Note • If you use a smartphone or tablet, make sure the Wi-Fi is enabled on the device.
Network Connection Problems Printer Suddenly Stopped Working for Some Reason Network Key (Password) Unknown Printer Cannot Be Used After Replacing Wireless Router or Changed Router Settings 335
Printer Suddenly Stopped Working for Some Reason Cannot Connect to a Printer after Network Configuration Changes Cannot Connect to a Printer via Wireless LAN (Wi-Fi) Cannot Connect to a Printer through Wireless Direct Cannot Connect to a Printer via Wired LAN Cannot Print through Network Cannot Connect to a Printer after Network Configuration Changes It may take a while for the computer to obtain an IP address, or you may need to restart your computer.
Note • Use 2.4 GHz frequency band to connect to a wireless router. Match the network name (SSID) set for the printer with that for 2.4 GHz frequency band of the wireless router. To check the current network settings of the printer, print out the network setting information. Printing Network Settings Note • IJ Network Device Setup Utility allows you to diagnose and repair the network status. Select the link below to download IJ Network Device Setup Utility and install it.
• For Windows: Starting Up IJ Network Device Setup Utility • For macOS: Starting Up IJ Network Device Setup Utility Check7 Make sure of the Wi-Fi channel numbers used for your computer. You need to have the same Wi-Fi channel number that you are using for the wireless router as your computer. It is normally set in the way that you can use all the Wi-Fi channels. However, when the channels that you are using are restricted, the Wi-Fi channels do not match.
Select Device settings > LAN settings > Wireless Direct > Switch WL Direct in this order and select Yes. Check3 Check the settings of your device (smartphone/tablet). Make sure Wi-Fi is enabled on your device. For details, refer to your device's instruction manual. Check4 Make sure printer is selected as connection for device (e.g. smartphone or tablet). Select the network name (SSID) for Wireless Direct specified for the printer as the connection destination for devices.
Check2 Make sure the LAN cable is connected properly. Make sure the printer is connected to the router with the LAN cable. If the LAN cable is loose, connect the cable properly. If the LAN cable is connected to the WAN side of the router, connect the cable to the LAN side of the router. If the problem is not resolved, redo setup from the web page. For Windows, you can redo setup using the Setup CD-ROM. Cannot Print through Network Check1 Make sure the computer is connected to the wireless router.
Network Key (Password) Unknown WPA/WPA2 or WEP Key Set for Wireless Router Unknown, Cannot Connect Setting an Encryption Key WPA/WPA2 or WEP Key Set for Wireless Router Unknown, Cannot Connect For more on setting up a wireless router, see the instruction manual provided with the wireless router or contact its manufacturer. Make sure your computer can communicate with the wireless router. Note • IJ Network Device Setup Utility allows you to diagnose and repair the network status.
• For macOS: Starting Up IJ Network Device Setup Utility Selecting WPA, WPA2, or WPA/WPA2 is recommended for security reason. If your wireless router is compatible with WPA/WPA2, you can also use WPA2 or WPA. • Using WPA/WPA2 (Windows) The authentication method, Wi-Fi password, and dynamic encryption type must be identical among the wireless router, the printer, and your computer. Enter the Wi-Fi password configured on the wireless router.
Printer Cannot Be Used After Replacing Wireless Router or Changed Router Settings When you replace a wireless router, redo the network setup for the printer according to the replaced one. Perform setup from the web page. For Windows, you can perform setup using the Setup CD-ROM. Note • IJ Network Device Setup Utility allows you to diagnose and repair the network status. Select the link below to download IJ Network Device Setup Utility and install it.
If using WPA/WPA2 key or a password, make sure encryption key for computer, network device, and printer matches key set for wireless router. Check3 The length or format of the Wi-Fi password and authentication method must be identical among the wireless router, the printer, and your computer. For details, see Setting an Encryption Key.
Other Network Problems Checking Network Information Restoring to Factory Defaults 345
Checking Network Information Checking Printer IP Address or MAC Address Checking Computer IP Address or MAC Address Checking Communication Between the Computer, the Printer, and the Wireless Router Checking Network Setting Information Checking Printer IP Address or MAC Address To check the printer's IP Address or MAC address, print out the network settings information. Printing Network Settings For Windows, you can check the network setting information on the computer screen.
3. Click TCP/IP to check the IP address, or click Hardware to check the MAC address. Checking Communication Between the Computer, the Printer, and the Wireless Router Perform a ping test to check if communication is taking place. • For Windows: 1. Select Command Prompt as shown below. In Windows 10, right-click Start and select Command Prompt. In Windows 8.1, select Command Prompt from the Start screen.
64 bytes from XXX.XXX.XXX.XXX: icmp_seq=0 ttl=64 time=3.394 ms 64 bytes from XXX.XXX.XXX.XXX: icmp_seq=1 ttl=64 time=1.786 ms 64 bytes from XXX.XXX.XXX.XXX: icmp_seq=2 ttl=64 time=1.739 ms --- XXX.XXX.XXX.XXX ping statistics --3 packets transmitted, 3 packets received, 0% packet loss If packet loss is 100%, communication is not taking place. Otherwise, computer is communicating with target device.
Restoring to Factory Defaults Important • Initialization erases all network settings on the printer, making printing operation from a computer over a network impossible. To use the printer over a network again after restoring it to the factory defaults, redo setup from the web page. For Windows, you can perform setup using the Setup CD-ROM. Initialize the network setting using the printer's operation panel.
Problems while Printing from Smartphone/Tablet Cannot Print from Smartphone/Tablet 350
Cannot Print from Smartphone/Tablet If you cannot print from your smartphone/tablet, it is possible that your smartphone/tablet cannot communicate with the printer. Check the cause of your problem according to the connection method.
To check the current network settings of the printer, print out the network setting information. Printing Network Settings Note • IJ Network Device Setup Utility allows you to diagnose and repair the network status. Select the link below to download IJ Network Device Setup Utility and install it. Checking Printer Connection Status Using IJ Network Device Setup Utility See below for starting up IJ Network Device Setup Utility.
Select the link below to download IJ Network Device Setup Utility and install it. Checking Printer Connection Status Using IJ Network Device Setup Utility See below for starting up IJ Network Device Setup Utility. • For Windows: Starting Up IJ Network Device Setup Utility • For macOS: Starting Up IJ Network Device Setup Utility Cannot Communicate with Printer while It Is in Wireless Direct If your smartphone/tablet cannot communicate with the printer in the Wireless Direct, check the following.
Check5 Have you entered the proper password specified for the Wireless Direct? To check the password specified for the printer, display it using the operation panel of the printer or print out the network setting information of the printer. • Display on the LCD. LAN settings • Print the network settings. Printing Network Settings Check6 Make sure the printer is not placed too far away from the device. If the distance between the printer and device is too far, wireless communication becomes poor.
Printing Problems Printer Does Not Print Ink Does Not Come Out Paper Does Not Feed Properly/"No Paper" Error Cannot Print on the Disc Label Printout Results Are Unsatisfactory 355
Printer Does Not Print Check1 Make sure printer is turned on. If not, make sure the printer is securely plugged in and press ON button to turn on. The ON lamp flashes while the printer is initializing. Wait until the ON lamp stops flashing and remains lit. Note • If you are printing large data such as photos or other graphics, printing may take longer to start. The ON lamp flashes while the computer is processing data and sending it to the printer. Wait until printing starts.
Select the link below to download IJ Network Device Setup Utility and install it. Checking Printer Connection Status Using IJ Network Device Setup Utility See below for starting up IJ Network Device Setup Utility. • For Windows: Starting Up IJ Network Device Setup Utility • For macOS: Starting Up IJ Network Device Setup Utility Make sure paper settings match information set for rear tray or cassette.
Note • If multiple printers are registered to your computer, select Set as Default Printer from System Preferences > Printers & Scanners for a printer to make the one selected by default. Check7 Are you trying to print a large data file? (Windows) If you are trying to print a large file, it takes a long time to start printing. If the printer does not start printing after a certain period of time, select On for Prevention of Print Data Loss on the Print Options dialog box.
Ink Does Not Come Out Check1 Make sure of the estimated ink levels in the ink tanks. Check the ink status on the LCD. Checking Ink Status on the LCD Check2 Are the orange tape and plastic wrap still on the ink tank? Make sure all the protective plastic wrap is peeled off to expose the Y-vent area, as shown below (A). If the orange tape remains on the ink tank (B), peel it off.
Paper Does Not Feed Properly/"No Paper" Error Check1 Make sure paper is loaded. Loading Paper Check2 When loading paper, consider the following. • When loading two or more sheets of paper, align the edges of the sheets before loading the paper. • When loading two or more sheets of paper, make sure the paper stack does not exceed the paper load limit.
If the paper tears in the rear tray, see List of Support Code for Error (Paper Jams) to remove it. If there are any foreign objects in the rear tray, be sure to turn off the printer, unplug it from the power supply, then remove the foreign object. Note • If the feed slot cover is opened, close it slowly. Check7 Clean paper feed roller.
Note • Cleaning the paper feed roller abrades it, so do this only when necessary. Check8 If two or more sheets of paper feed from cassette at once, clean inside of cassette. Cleaning Cassette Pads Check9 Are transport unit cover and rear cover attached properly? See Rear View for the positions of the transport unit cover and the rear cover. If the measures above do not solve the problem, contact your nearest Canon service center to request a repair.
Cannot Print on the Disc Label Disc Label Printing Does Not Start Multi-Purpose Tray Does Not Feed Properly Multi-Purpose Tray Jammed Disc Label Printing Does Not Start Check1 Is multi-purpose tray placed properly? Place the multi-purpose tray properly again and press the printer's OK button. Use the multi-purpose tray supplied with this printer. For more on placing the multi-purpose tray, see Placing a Printable Disc.
Multi-Purpose Tray Jammed Pull out the multi-purpose tray gently. If the multi-purpose tray cannot be pulled out, cycle the power switch. The multi-purpose tray will automatically be ejected. When the multi-purpose tray is pulled out, place the multi-purpose tray again and retry printing. For more on placing the multi-purpose tray, see Placing a Printable Disc. If the multi-purpose tray is still jammed, check if there is a problem with the printable disc.
Printout Results Are Unsatisfactory If the print results are unsatisfactory due to white streaks, misaligned/distorted lines, or uneven colors, check the paper and print quality settings first. Do page size and media type settings match size and type of loaded paper? Check1 If these settings do not match, it is not possible to obtain the proper result. If you are printing a photograph or an illustration, an incorrect paper type setting may reduce the quality of the printout color.
See also the sections below: Printouts Are Blank/Blurry or Fuzzy/Inaccurate or Bleeding Colors/Streaks or Lines Lines Are Misaligned/Distorted Paper Is Smudged / Printed Surface Is Scratched Vertical Line Next to Image Cannot Complete Printing Part of Page Is Not Printed (Windows) Lines Incomplete or Missing (Windows) Images Incomplete or Missing (Windows) Ink Blots / Paper Curl Back of Paper Is Smudged Uneven or Streaked Colors 366
Printouts Are Blank/Blurry or Fuzzy/Inaccurate or Bleeding Colors/ Streaks or Lines Printing Is Blurry Colors Are Wrong 367
White Streaks Appear Check1 Check paper and print quality settings. Printout Results Are Unsatisfactory Check2 Check status of ink tanks. Replace ink tank if ink has run out. Replacing Ink Tanks Check3 Are the orange tape and plastic wrap still on the ink tank? Make sure all the protective plastic wrap is peeled off to expose the Y-vent area, as shown below (A). If the orange tape remains on the ink tank (B), peel it off.
• If problem is not resolved after performing print head cleaning twice: Perform print head deep cleaning. If the problem is not resolved after performing print head deep cleaning, turn off the printer and perform print head deep cleaning again 24 hours later. • If problem is not resolved after performing print head deep cleaning twice: If print head deep cleaning does not resolve the problem, the print head may be damaged. Contact your nearest Canon service center to request a repair.
Lines Are Misaligned/Distorted Check1 Check paper and print quality settings. Printout Results Are Unsatisfactory Check2 Perform print head alignment. If printed lines are misaligned/distorted or print results are otherwise unsatisfactory, adjust the print head position. Aligning the Print Head Note • If the problem is not resolved after performing the print head alignment, perform print head alignment manually from your computer.
Paper Is Smudged / Printed Surface Is Scratched Paper Is Smudged Smudged Edges Smudged Surface Printed Surface Is Scratched Check1 Check paper and print quality settings. Printout Results Are Unsatisfactory Check2 Check paper type. Make sure you are using the right paper for what you are printing. Supported Media Types Check3 Correct curl before loading paper. When using Photo Paper Plus Semi-gloss, even if the sheet is curled, load one sheet at a time as it is.
1. Roll up paper in opposite direction to paper curl as shown below. 2. Check that paper is now flat. We recommend printing curl-corrected paper one sheet at a time. Note • Depending on paper type, the paper may smudge or may not feed properly even if it is not curled inward. Follow the instructions below to curl the paper outward up to 0.1 in. / 3 mm (C) in height before printing. This may improve the print result.
2. Open Canon IJ Printer Assistant Tool. Opening the Maintenance Tool (Canon IJ Printer Assistant Tool) 3. Select Custom Settings. 4. Select Prevents paper abrasion check box and select OK. 5. Check message and select OK. • From computer (macOS): Adjust the setting to prevent paper abrasion from Remote UI. Opening Remote UI for Maintenance Check5 If brightness is set low, increase brightness setting and try printing again.
3. Select Custom Settings. 4. Drag Ink Drying Wait Time slide bar to set the wait time and select OK. 5. Check message and select OK. • For macOS: Set the waiting time using Remote UI.
Vertical Line Next to Image Check Is loaded paper size correct? If the loaded paper is larger than the size you specified, a vertical line may appear in the margin. Set the paper size to match the loaded paper. Printout Results Are Unsatisfactory Note • The direction of the vertical line pattern may vary depending on the image data or the print setting. • This printer performs automatic cleaning when necessary to keep printouts clean. A small amount of ink is ejected for cleaning.
Mechanical Problems Printer Does Not Turn On Printer Turns Off Unexpectedly or Repeatedly USB Connection Problems Cannot Communicate with Printer via USB Wrong Language Appears in LCD 376
Printer Does Not Turn On Check1 Press ON button. Check2 Make sure power plug is securely connected to printer, and then turn on again. Check3 Unplug printer, leave it for at least 2 minutes, and then plug it back in and turn on again. If this does not solve the problem, contact your nearest Canon service center to request a repair.
Printer Turns Off Unexpectedly or Repeatedly Check If printer is set to turn off automatically after a certain time, disable this setting. If you have set the printer to turn off automatically after a specified time, the power will shut off by itself once that time has elapsed. • To disable the setting from the operation panel: 1. Check that printer is turned on. 2. Press the Setup button, use the button to select ECO settings, and press the OK button. LCD and Operation Panel 3.
USB Connection Problems Make sure of the checking item below when you find one of the followings. • Printing is slow. • Hi-Speed USB connection does not work. • A message such as "This device can perform faster" appears. (Windows) Note • If your system environment does not support Hi-Speed USB, the printer operates at the slower speed of USB 1.1. In this case, the printer works properly but printing speed may slow down due to the communication speed.
Cannot Communicate with Printer via USB Check1 Make sure printer is turned on. Check2 Connect USB cable properly. As the illustration below, the USB port is at the back of the printer. Important • Connect the "Type-B" terminal to the printer with the notched side facing UP. For details, refer to the instruction manual supplied with the USB cable. Make sure Enable bidirectional support is selected in the Ports sheet of the Printer properties dialog box.
Wrong Language Appears in LCD Follow the instructions below to select your language. 1. Press Setup button and wait a little. 2. Press button once and press OK button. 3. Press button 5 times and press OK button. 4. Use button to select language for LCD and press OK button. The desired language appears on the LCD. 5. Press Stop button.
Installation and Download Problems Failed to Printer Driver Installation (Windows) Updating Printer Driver in Network Environment (Windows) 382
Failed to Printer Driver Installation (Windows) If installation does not start when you insert Setup CD-ROM: If you cannot get past the Printer Connection screen: Other cases: If installation does not start when you insert Setup CD-ROM: Follow the instructions below to start the installation. 1. Make the following settings. • In Windows 10, click Start > File Explorer, and then click This PC from list on left. • In Windows 8.
If you cannot get past the Printer Connection screen: Cannot Proceed beyond Printer Connection Screen Other cases: If the printer driver was not installed correctly, uninstall the printer driver, restart your computer, and then reinstall the printer driver. Deleting the Unnecessary Printer Driver Reinstall the printer driver with the Setup CD-ROM or install it from the Canon website.
Updating Printer Driver in Network Environment (Windows) Download the latest printer driver. Download the latest printer driver for your model on the download page of the Canon website. Uninstall the existing printer driver and follow the installation instructions to install the latest printer driver that you downloaded. In the connection method selection screen, select Use the printer with Wi-Fi connection or Use the printer with wired LAN connection according to the connection method you use.
Errors and Messages Four-Digit Alphanumeric Characters Appear on LCD When Error Occurred Message (Support Code) Appears 386
Four-Digit Alphanumeric Characters Appear on LCD A message appears on the LCD or your computer screen. Depending on an error or message, four-digit alphanumeric characters appear. The characters represent a "support code" (error number). For details on each support code, see List of Support Code for Error.
When Error Occurred If an error occurs in printing, for example if the paper runs out or jams, a troubleshooting message appears automatically. Take the appropriate action described in the message. When an error occurs, a message appears on the computer, or an error code appears on the printer. For some errors, a support code (error number) appears on the computer screen.
Message (Support Code) Appears This section describes some of the errors and messages that may appear. Note • A support code (error number) is displayed on the computer for some errors. For details on errors that have support code, see List of Support Code for Error. If a message appears on the LCD, see below. Message Appears on LCD If a message appears on the computer, see below.
Error Regarding Power Cord Being Unplugged Is Displayed (Windows) The printer may have been unplugged while it was on. Check the error message that appears on the computer and click OK. The printer starts printing. See Unplugging the Printer for unplugging the power cord. Writing Error/Output Error/Communication Error (Windows) Check1 If the ON lamp is off, make sure printer is plugged in and turn on. The ON lamp flashes while the printer is initializing.
If USB Printing Support Properties screen does not appear, make sure the printer is correctly connected to the computer. Check2 Make sure printer is properly connected to computer. 3. Click General tab and check for a device problem. If a device error is shown, see Windows Help to resolve it.
List of Support Code for Error Support code appears on the LCD and your computer screen when errors occur. A "support code" is an error number, and appears along with an error message. When an error occurs, check the support code displayed on the LCD and computer screen and take the appropriate action in response.
6801 6830 6831 6832 6833 6900 6901 6902 6910 6911 6920 6921 6930 6931 6932 6933 6940 6941 6942 6943 6944 6945 6946 6951 6A80 6A81 6D01 • 7000 to 7ZZZ 7500 7600 7700 7800 • 8000 to 8ZZZ 8300 • A000 to ZZZZ C000 For paper jam support codes, see also List of Support Code for Error (Paper Jams).
List of Support Code for Error (Paper Jams) If paper jams, remove it following the appropriate procedure as shown below.
1300 Cause Paper is jammed when feeding paper from rear tray. What to Do If the paper fed from the rear tray is jammed, remove the jammed paper from the paper output slot or from the rear tray following the instructions below. 1. Slowly pull out paper, either from paper output slot or from rear tray, whichever is easier. Hold the paper with both hands, and pull it out slowly so as not to tear it. Note • If you cannot pull out the paper, turn the printer back on without pulling forcibly.
If you turned off the printer in step 1, the print data that was sent to the printer is erased. Redo the printing. Note • When reloading the paper, make sure you are using suitable paper and loading it correctly. • We recommend using paper sizes other than A5 to print documents with photos or graphics. A5 paper may curl and jam as it leaves the printer. If the measures above do not solve the problem, contact your nearest Canon service center to request a repair.
1303 Cause Paper is jammed when feeding paper from cassette. What to Do 1. Remove jammed paper. • If the paper is jammed at the paper output slot: 1300 • If the paper is jammed inside the printer: Paper Is Jammed inside Printer • If the paper is jammed at the feeder of the cassette: Pull out the cassette, and then remove the paper slowly with both hands. • If none of the above is applied, see Removing Jammed Paper from Rear Side to open the rear cover and to remove the paper. 2.
1304 Cause Paper is jammed when performing automatic duplex printing. What to Do 1. Remove jammed paper. • If the paper is jammed at the paper output slot: 1300 • If the paper is jammed inside the printer: Paper Is Jammed inside Printer • If the paper is jammed at the feeder of the cassette: Pull out the cassette, and then remove the paper slowly with both hands. • If none of the above is applied, see Removing Jammed Paper from Rear Side to open the rear cover and to remove the paper. 2.
1313 Cause Paper is jammed as printer pulled in printed paper. What to Do If the paper is jammed as the printer pulled in the printed paper, try to remove the paper from the following locations.
Paper Is Jammed inside Printer If the jammed paper tears and you cannot remove the paper from the paper output slot, or if the jammed paper remains inside the printer, remove the paper following the instructions below. Note • If paper becomes jammed during printing and you need to turn off the printer to remove it, press the Stop button to stop the printing before you turn off the printer. 1. Turn off printer and unplug it. 2. Open top cover. Important • Do not touch white belt (A).
4. Hold jammed paper firmly in both hands. If the paper is rolled up, pull out it. 5. Slowly pull out paper, so as not to tear it. Pull out the paper at an angle of about 45 degrees.
6. Make sure all jammed paper is removed. If the paper tears when you pull out it, a bit of paper may remain in the printer. Check the following and remove any remaining paper. • Any paper left under the print head holder? • Any small bits of paper left in the printer? • Any paper left in the left and right empty spaces (B) in the printer? 7. Close top cover. All jobs in the print queue are canceled. Redo the printing.
Removing Jammed Paper from Rear Side Note • If paper becomes jammed during printing and you need to turn off the printer to remove it, press the Stop button to stop the printing before you turn off the printer. 1. Make sure you have unplugged the power cord. 2. Rotate printer so that rear side of printer faces toward you. 3. Detach rear cover. Pull out the rear cover.
4. Slowly pull out paper. Note • Do not touch the inner parts of the printer. If you were not able to remove the paper in this step, detach the transport unit cover and remove the paper by following these steps. 1. Detach transport unit cover. Lift up the transport unit cover and pull out it. 2. Slowly pull out paper. Note • Do not touch the inner parts of the printer. 3. Make sure all jammed paper is removed.
4. Attach transport unit cover. Insert the transport unit cover slowly all the way into printer and take down the transport unit cover. 5. Attach rear cover. Insert the projections of the right side of the rear cover into the printer, and then push the left side of the rear cover until it is closed completely. The print data that was sent to the printer is erased. Redo the printing. Note • When reloading the paper, make sure you are using suitable paper and loading it correctly.
1000 Cause Possible causes include the following. • There is no paper in the rear tray. • Paper is not loaded in the rear tray properly. What to Do Take the corresponding actions below. • Load paper in the rear tray. Loading Paper in the Rear Tray • Align the paper guides with the both edges of the paper when you load paper in the rear tray. • Set paper information for the paper in the rear tray. After carrying out the above measures, press the printer's OK button.
1003 Cause Possible causes include the following. • There is no paper in the cassette. • Paper is not loaded in the cassette properly. What to Do Take the corresponding actions below. • Load paper in the cassette. Loading Paper in the Cassette • Align the paper guides with the both edges of the paper when you load paper in the cassette. • Set paper information for the paper in the cassette. After carrying out the above measures, press the printer's OK button.
1013 Cause Multi-purpose tray compatible media is not set on multi-purpose tray, or the media position is misaligned. What to Do Set the multi-purpose tray compatible media properly by following these steps. 1. Remove multi-purpose tray. 2. Place multi-purpose tray compatible media on multi-purpose tray properly. Placing Multi-purpose Tray 2. Place multi-purpose tray on multi-purpose tray guide. 3. Press the printer's OK button. The printer starts printing.
1200 Cause Top cover is open. What to Do Close the top cover and wait for a while. Do not close it while you are replacing an ink tank.
1401 Cause Print head may be damaged. What to Do Turn off the printer and turn it back on. If this does not solve the problem, contact your nearest Canon service center to request a repair.
1600 Cause Ink may have run out. What to Do Replacing the ink tank is recommended. If printing is in progress and you want to continue printing, press the printer's OK button with the ink tank installed. Then printing can continue. Replacing the ink tank is recommended after the printing. The printer may be damaged if printing is continued under the ink out condition.
1660 Cause The ink tank cannot be recognized. What to Do Printing cannot be performed because the ink tank is not installed or is not compatible with this printer. Check the ink tank. If you want to cancel printing, press the printer's Stop button.
1688 Cause The ink has run out. What to Do Replace the ink tank and close the top cover. Printing under the current condition may damage the printer. If you want to continue printing in this condition, you need to disable the function for detecting the remaining ink level. Press and hold the printer's Stop button for at least 5 seconds, and then release it. With this operation, disabling the function for detecting the remaining ink level is memorized.
1689 Cause Printer detected ink out condition. What to Do Replace the ink tank and close the top cover. An ink tank that was once empty is installed. Printing under the ink out condition may damage the printer. If you want to continue printing, you need to disable the function for detecting the remaining ink level. To disable this function, press and hold the printer's Stop button for at least 5 seconds, and then release it.
1700 Cause Ink absorber is almost full. What to Do Press the printer's OK button to continue printing. Contact your nearest Canon service center to request a repair. Note • In the case of warnings or errors caused by remaining ink levels, the printer cannot print.
1890 Cause Tape for securing print head holder during transportation may still be attached. What to Do Open the top cover and make sure the tape for securing the print head holder during transportation has been removed. If the tape is still there, remove it and close the top cover. If this does not solve the problem, contact your nearest Canon service center to request a repair.
2110 Cause Paper settings for printing do not match cassette paper information set on printer. Note • See below for the correct correspondence between paper settings made on the printer driver or on the LCD. Paper Settings on the Printer Driver and the Printer (Media Type) (Windows) Paper Settings on the Printer Driver and the Printer (Paper Size) (Windows) • See below for details on cassette paper information set on the printer.
For example, if the print paper setting is A5, and cassette paper information is set to A4, change the paper in the cassette to A5 paper and proceed with printing. Once you have inserted the cassette after changing the paper, the screen for setting cassette paper information appears. Set paper information for the paper in the cassette. Note • See below for the correct correspondence between paper settings made on the printer driver or on the LCD.
2113 Cause Paper settings for printing do not match either rear tray or cassette paper information set on printer. Note • See below for the correct correspondence between paper settings made on the printer driver or on the LCD. Paper Settings on the Printer Driver and the Printer (Media Type) (Windows) Paper Settings on the Printer Driver and the Printer (Paper Size) (Windows) • See below for details on rear tray or cassette paper information set on the printer.
For example, if the print paper setting is A5, and rear tray and cassette paper information are set to A4, change the paper in the rear tray or the cassette to A5 paper and proceed with printing. Once you have changed the paper, the screen for setting rear tray or cassette paper information appears. Set paper information for the paper. Note • See below for the correct correspondence between paper settings made on the printer driver or on the LCD.
2114 Cause Paper settings for printing do not match rear tray paper information set on printer. Note • See below for the correct correspondence between paper settings made on the printer driver or on the LCD. Paper Settings on the Printer Driver and the Printer (Media Type) (Windows) Paper Settings on the Printer Driver and the Printer (Paper Size) (Windows) • See below for details on rear tray paper information set on the printer.
For example, if the print paper setting is A5, and rear tray paper information is set to A4, change the paper in the rear tray to A5 paper and proceed with printing. Once you have changed the paper, the screen for setting rear tray paper information appears. Set paper information for the paper in the rear tray. Note • See below for the correct correspondence between paper settings made on the printer driver or on the LCD.
4103 Cause Cannot perform printing with current print settings. What to Do Press the printer's Stop button to cancel printing. Then change the print settings and retry printing.
5100 Cause Printer error has occurred. What to Do Cancel printing and turn off the printer. Check the following: • Make sure print head holder motion is not impeded by tapes for securing the print head holder during transportation, jammed paper, etc. Remove any impediment. • Make sure the ink tanks are properly installed. Press ink tanks until they click into place. Turn the printer back on. If this does not solve the problem, contact your nearest Canon service center to request a repair.
5200 Cause Printer error has occurred. What to Do Turn off printer and unplug it. After a while, plug in the printer again and turn it back on. If this does not solve the problem, contact your nearest Canon service center to request a repair.
5B00 Cause Printer error has occurred. What to Do Contact your nearest Canon service center to request a repair. Note • In the case of warnings or errors caused by remaining ink levels, the printer cannot print.
6000 Cause Printer error has occurred. What to Do If the paper is jammed, remove it depending on the jammed location and cause. List of Support Code for Error (Paper Jams) Turn off printer and unplug it. Plug in the printer again and turn it back on. If this does not solve the problem, contact your nearest Canon service center to request a repair.
C000 Cause Printer error has occurred. What to Do Turn off printer and unplug it. Plug in the printer again and turn it back on. If this does not solve the problem, contact your nearest Canon service center to request a repair.
