& © CANON ING. 2002 PRINTED IN CHINA PRIME EN CHINE IMPRESARIO EN CHINA Handling Precautions . Before taking pictures of important events. such as weddings and rips, check to make sure the camera is working properly. 2. This camera Is not resistant to water, and should not be used outdoors i iris gaining or showing. Keep the camera out of salt spray and excessive humidity. I used at fife beach, clean it thoroughly afterward with a dry cloth, 3. Tore the camera in & cool, dy, dustless place.
i Nomenclature Front (1) Shutter bunion . @ (8] Zoom-in (telephoto) Sel button @ [# zoom-out {wide-angle)/ Selection @G bunion () Main switch Grassing the main switch fums the camera on and sets the lens to the wide-angle position. if you press it again, the lens retracts. the lens cover closes and the camera switches off. Wuhan you switch the camera off.
@ [MODE Mode button @ @ Flash mode bunion (@ Back cover release lever 8 Flash 1D Viewfinder window 42 AF sensor/metering window Soiling on the AF sensor causes focusing problems. Wipe off any dust or dint before taking pictures. B Lens Soiling on the lens causes focusing problems. Wipe off any dust or dirt before taking pictures.
m “ 88 +1.57 Tear LCD Panel (Normally, only necessary information displayed) Dateless BT/ @) Portrait Custom Function number 44 Night portrait @ Manual exposure compensation &) Action (3 Red-eve reduction mark 12 Battery lave! indicator @ Frame counter 13 Seltzer Film mark 43 & Flash ON (Fires for all shots) &) Mealtime release 45 @ Flash OFF (Never fires) @ Close-up 1 Autopilot @ Mode selection indicator 0 When "H" is displayed.
CECILE Loading the Battery Applicable Battery: One lithium battery (CH2) 4 Open the battery cover. J Load a new battery. @ Align the + = terminals correctly and inert the battery end first, wh The Wb appears on the LCD panel. 2 Close the battery cover. @ Push the cover closed until you hear a clicking sound. = he date display the LCD panel blinks Set the date and time.
Loading and Removing the Film B Loading the Film 1 Open the back cover and load the film. @ Push the back cover release lover down, Position the film correctly between the film guides. 3 Pull the film out to the ,BERK Et {film leader position indicator). @ Make sure that there is no slack in the Tim when you pull it out, @ i the edge of the film leader goes payola the Him leader position indicator, rewind some of the film back into the cartridge. £1 Close the back cover.
long as the subjects in the wide area AF frame, the subject will be in focus. The flash also fires automatically in low light or backbit conditions. ’f Press the main switch to turn the camera on. 3 Decide on the size of your sublet, @ Pressing [8) zooms In on your subject while pressing [#944 zooms out for a wide-angle shot 3 set the focus. ® Position the wide area AF frame over your subject and Tightly press the shutter bullion hallway down. = When the subject is in focus, the green lamp lights.
Using Focus Lock Lock the focus when you want the subject (o be off center. or when the subject is within 1 /3.3 ft. of the camera. 1 Set the focus. ® Position the wide ares AF mare aver your subject and lightly prods the shutter button halfway down, Keep the sutler button pressed hallway, "2 Compose the shot and take the picture, @ Compose fhe shot and press the shutter bunion fully. change.
W e e The self-timer function allows you to take a picture from a distance away from the camera when it is attached 1o a tripod. ’] Set the camera to self-timer mode. ® Press the & button, = %) appears on the LCD panel. @ I you then press the &) button again, &) disappears and self-timer mode is canceled. 2 Compose the picture and press the shutter button. = The self-timer lamp blinks and the shelter 15 released approximately 10 seconds later. @ To cancel the self-timer, press the &) button again.
"‘A\ Shooting Portraits Use this mode when you want 1o lessen the impact of the background and highlight the subject The camera automatically zoom sin, arrange forth 1H5u, and 110 2.5 my/3.3 10 8.2 . for the 1050 to frame from the waist Up of the subject and fires the flash for every shot to produce highlights in the subject’s eyes. ® Follow the steps in auto flash mode to take a picture. & The red ove reduction function will operate. m Shooting Close-up Use this mode when you want to take close.
Using Red-eye Reduction Function Selectively When you use the flash to take photos of people in fow light conditions that ayes sometimes glow red in the photograph. This is referred o as the red-eye effect and is caused by the light of the flash being reflected off the resting of the eye. When the red-eye reduction operates. the red-eye reduction lamp fights for approximately 1 second before the Hash fires. This causes the subject's pupils to contract, minimizing the risk of err-eye.
w10 548 Auto flash with He-eye Reduction in dark places. the flash automatically fires after the red-eye reduction lamp has L & Fish ON (Fires for all shots) The flash fires when the picture is fake. €5 Flash OFF (Never fires) The flash does not fire.
B Setting the Date and Time When you replace the battery or travel to the different time zone, use the following procedure to set or adjust the date and tme tastings. 4 Select the Date made. 2 Press the B3 button for more than 2 seconds for teatime set mode. 3 Press the il button to select the settling position (numbers blinking). @ Set ling position cycles through in the order £ Cross the [9] button to set the number, % Repeat 3 and 4 above to set all digits of the date and time.
Selling the Custom Functions You can customize the functions listed below to suit your preferences or he photography conditions. 1 Set the camera to Custom Function setting mode. ® With the power off, hold down the & button and press the @ bunion. ='CF 1-0" appears on the LCD panel. 2 Select a function. @ Each time you press the [] button. the Custom Function dumber changes in the cycle shown below EGH = CF2 = CE3 2 CF-» CFh j 3 Set the function.