User’s Manual ENGLISH MULTIMEDIA PROJECTOR
Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. © Copyright 2015 Disclaimer The information in this document is subject to change without notice.
Projector Installation Notice Place the projector in a horizontal position The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed in any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically, and may lead to other unpredictable damages. Allow at least 50 cm clearance around the exhaust vent. Ensure that the intake vents do not recycle hot air from the exhaust vent.
Power Safety Only use the supplied power cord. Do not place anything on the power cord. Place the power cord where it will not be in the way of foot traffic. Remove the batteries from the remote control when storing or not in use for a prolonged period. Replacing the Lamp Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 52 for clear and safe instructions for this procedure. Before replacing the lamp: Unplug the power cord.
Table of Contents SAFETY INSTRUCTIONS .................................................................................................................................................. 1 GETTING STARTED ......................................................................................................................................................... 11 PACKING CHECKLIST ......................................................................................................................................
SPECIFICATIONS ............................................................................................................................................................. 60 PRODUCT SPECIFICATIONS................................................................................................................................................. 60 INSTALLATION DISTANCE VS. PROJECTION SIZE ................................................................................................................
SAFETY INSTRUCTIONS Before installing and operating the projector, read this manual thoroughly. This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintain it in good condition for many years to come. Improper operation may result in not only shortening the product life, but also malfunctions, fire hazards, or other accidents.
Safety Precautions WARNING: • THIS APPARATUS MUST BE GROUNDED. • TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. • This projector produces intense light from the projection lens. Do not stare directly into the lens, otherwise eye damage could result. Be especially careful that children do not stare directly into the beam. • Install the projector in a proper position. Otherwise it may result in a fire hazard.
Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. For wall or shelf mounting, use a tool such as a mounting kit to secure the projector. An appliance and cart combination should be moved with care.
AC Power Cord Requirement The AC Power Cord supplied with this projector meets the requirements for use in the country you purchased it. AC Power Cord for the United States and Canada: The AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA). Ground The AC Power Cord has a grounding-type AC line plug. This is a safety feature to ensure the plug fits into the power outlet.
Federal Communication Commission Notice Multimedia Projector, Model: LV-WX300UST/LV-WX300USTi This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Precautions for Use As this section contains important safety-related information, be sure to read the following carefully beforehand in order to use your projector correctly and safely. If the following situations occur, turn the power off, remove the power plug from the power outlet and contact the Canon Customer Support Center. Failure to do so could cause a fire or result in an electric shock.
Pay attention to the following points regarding the power source, power plug and handling of the connector. Failure to do so could result in a fire, electric shock or personal injury. • Do not use any power source with a voltage other than the voltage indicated (AC 100 – 240 V). • Do not pull the power cord and be sure to hold the power plug or connector when removing. The cord could be damaged as a result. • Do not insert any metal objects into the contact parts of the power plug or connector.
Pay attention to the following points regarding installation and handling of the projector. • If the projector will not be used for a long period of time, be sure to remove the power plug from the power outlet to ensure safety. Failure to do so could cause a fire. • The temperature of the cabinet around and above the exhaust vents can become hot during projector operation. Touching these areas during operation could cause burns to the hands. Do not touch these areas. Doing so may cause burns.
Precautions when replacing lamps that stop working • If illumination suddenly stops, either when you turn the projector on or after it has been on for a while, the lamp may have ruptured. In this case, never attempt to replace the lamp by yourself. Always request service from the Canon Customer Support Center. Additionally, with ceiling-mounted projectors, the lamp may fall out when you open the lamp cover or while you are attempting to replace it.
For Safe Use Pay attention to the following points when carrying or transporting the projector. • This projector is a precision instrument. Do not knock it over or subject it to impacts. Doing so may cause a malfunction. • Do not reuse any packaging or shock-absorbent materials that were supplied with the projector at the time of purchase for transporting or shipping the projector. Protection of the projector cannot be guaranteed if used packaging or shock-absorbent materials are reused.
GETTING STARTED Packing Checklist Carefully unpack the projector and check that the following items are included: LV-WX300UST REMOTE CONTROL (WITH ONE 3V CR2025 BATTERY) LV-WX300USTI POWER CORD (1.8 M / 5.9') COMPUTER CABLE (1.8 M / 5.9') (MINI D-SUB 15-PIN / MINI D-SUB 15-PIN) Warranty Card CD-ROM (THIS USER’S MANUAL) IMPORTANT INFORMATION WARRANTY CARD The Following ITEMS only for LV-WX300USTi CD-ROM (INTERACTIVE DRIVER AND SOFTWARE) USB CABLE (A-TYPE TO MINI 5.0M/16.
Views of Projector Parts Front-right View 1 2 ITEM 3 4 5 6 LABEL 7 DESCRIPTION SEE PAGE: 1. Lamp cover Removes cover to replace lamp module / unit ---> lamp 2. IR receiver Receives IR signal from remote control 3. Lens Projection Lens 4. Focus ring Focuses the projected image 5. Function keys See Top view—On-screen Display (OSD) buttons and LEDs. 6. Interactive Camera Interactive function use *Not Available in LV-WX300UST 7.
Top view—On-screen Display (OSD) buttons and LEDs 1 2 6 3 7 4 8 5 9 12 10 11 ITEM 1. LABEL MENU SOURCE 4. 5. OK Enter or confirm highlighted OSD menu item 6. AUTO Optimizes image size, position, and resolution 7. Navigates and changes settings in the OSD 8. Navigates in the OSD Quick Menu – For Keystone 9. Turns the projector On or Off LAMP LED 11. POWER LED 12. TEMP LED PAGE: 25 Enter the Source menu Navigates and changes settings in the OSD 10.
Rear view 1 19 ITEM 2 3 4 18 5 6 7 89 17 15 14 13 12 16 LABEL 10 11 DESCRIPTION SEE PAGE: 1. Security bar For security and authorized usage 2. Kensington lock Secure to permanent object with a Kensington® Lock system 3. USB POWER (5V-2A) Connect the USB cable for power supply.(for Interactive function) *not available in LV-WX300UST 4. AUDIO L/R (For VIDEO/ S-VIDEO) Connect an AUDIO cable from the audio device 5.
ITEM LABEL DESCRIPTION 16. HDMI 2 Connect the HDMI cable from a HDMI device* 17. VIDEO Connect the composite cable from a video device 18. HDMI 1 Connect the HDMI cable from a HDMI device* 19. RJ – 45 Connect a LAN cable from Ethernet SEE PAGE: * It is necessary to turn the 3D setting off in case of connecting with some digital cameras by HDMI.
Bottom view 2 2 2 1 135.51 247.01 1 1 ITEM LABEL DESCRIPTION SEE PAGE: 1. Tilt adjustor Rotate adjuster lever to adjust angle position 23 2. Ceiling support holes Contact your dealer for information on mounting the projector on a ceiling Warning: The ceiling attachment (part No.: LV-WL02) is required in order to mount the projector on the wall. Make sure to ask the Canon Customer Support Center if you want to install the Wall Attachment.
Remote Control Parts 12 15 3 14 13 12 4 11 6 10 7 5 9 8 Important: 1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the remote control and the projector. If the path between the remote control and the projector is obstructed, you can bounce the signal off certain reflective surfaces such as projector screens. 3.
ITEM LABEL DESCRIPTION SEE PAGE: 1. Up cursor Navigates and changes settings in the OSD 2. Enter Changes settings in the OSD 3. Power Turns the projector On or Off 20 4. Right cursor Navigates and changes settings in the OSD 25 5. Volume + Increase volume 25 24 6. Volume - Decrease volume 7. Mute Mutes the built-in speaker 8. Freeze Freeze/unfreezes the on-screen picture 9. Source Detects the input device 10.
SETUP AND OPERATION Inserting the Remote Control Batteries 1. Remove the battery compartment cover by sliding the cover in the direction of the arrow (A). Pull out the cover (B).. 2. Insert the battery with the positive side facing up. 3. Replace the cover. Caution: 1. Only use a 3V lithium battery (CR2025). 2. Dispose of used batteries according to local ordinance regulations. 3. Remove the battery when not using the projector for prolonged periods.
Starting and Shutting down the Projector 1. Connect the power cord to the projector. Connect the other end to a wall outlet. 2. Turn on the connected devices. 3. Ensure the POWER LED displays a solid green. Then press the POWER button of the remote to turn on the projector. The projector splash screen displays and connected devices are detected. See Setting an Access Password (Security Lock) on page 21 if security lock is enabled. 4.
Setting an Access Password (Security Lock) You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector. When enabled, the password must be entered after you power on the projector. (See Navigating the OSD on page 25 and Setting the OSD Language on page 26 for help on using OSD menus.) Important: Keep the password in a safe place. Without the password, you will not be able to use the projector.
4. 5. Press the cursor ▲▼ button to select Security Lock. Press the cursor ◄► button to enable or disable security lock function. A password dialog box automatically appears. 6. You can use the cursor buttons ▲▼◄► on IR remote control for password entry. You can use any combination including the same arrow five times, but not less than five. Press the cursor buttons in any order to set the password. Push the MENU button to exit the dialog box. 7.
Adjusting the Projector Level Take note of the following when setting up the projector: The projector table or stand should be level and sturdy. Position the projector so that it is perpendicular to the screen. Ensure the cables are in a safe location. You could trip over them. To adjust the angle of the picture, turn the tilt-adjuster right or left until the desired angle has been achieved.
Adjusting the Focus and Keystone 1. Use the Image-focus control (on the projector only) to sharpen the projected image 2. Use the KEYSTONE buttons on the remote control to correct keystone distortion (wider top or bottom) effect. 3. The keystone control appears on the display. Adjusting the Volume 1. Press the Volume +/buttons on the remote control. The volume control appears on the display. 2. Press the MUTE button to turn off the volume. (This feature is available only on the remote).
ON-SCREEN DISPLAY (OSD) MENU SETTINGS OSD Menu Controls The projector has an OSD that lets you make image adjustments and change various settings. Navigating the OSD You can use the remote control cursor buttons or the projector keypad to navigate and make changes to the OSD. 4 6 1 1 4 2 2 2 3 6 5 1 1 2 3 5 1. To enter the OSD, press the MENU button. 2. There are five menus. Press the cursor ◄► button to move through the menus. 3. Press the cursor ▲▼ button to move up and down in a menu. 4.
Setting the OSD Language Set the OSD language to your preference before continuing. 1. Press the MENU button. Press the cursor ◄► button to navigate to Installation I. 2. Press the cursor ▲▼ button until Language is highlighted. 3. Press the cursor ◄► button until the language you want is highlighted. 4. Press the MENU button twice to close the OSD.
OSD Menu Overview Use the following illustration to quickly find a setting or determine the range for a setting. MAIN MENU SUB MENU SETTINGS Image Brilliant Color Standard, Presentation, sRGB, Movie, User 0~10 Brightness 0~100 Contrast 0~100 Sharpness 0~31 Gamma 2.0, 2.2, 2.4, 2.6, 2.
MAIN MENU SUB MENU SETTINGS Installation I English, Français, Deutsch, Español, Português, 簡体中文, 繁體中文, Italiano, Svenska, Nederlands, Русский, Suomi, 한국어, العربية, Türkçe, 日本語, Dansk, Polski, Magyar, Čeština, ไทย Black, Red, Green, Blue, White Language Blank Screen Image Flip H/V Front Table, Rear Table, Front Ceiling, Rear Ceiling Fill, 4:3, 16:9, Letter Box, Native Aspect Test Pattern Off, Cross Hatch, RGB Ramps, Color Bars, Stair Step, Checker, Horizontal Lines, Vertical Lines, Diagonal Lines,
MAIN MENU SUB MENU SETTINGS Installation II Auto Search Off, On Auto Power Off (min.
Image Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Image Menu. Press the cursor ▲▼ button to move up and down in the Image menu. Press ◄► to change values for settings. ITEM DESCRIPTION Image Mode Press the cursor ◄► button to set the Image Mode. Brilliant Color Press the cursor ◄► button to adjust the Brilliant Color value. Brightness Press the cursor ◄► button to adjust the display brightness.
Advanced Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Image menu. Press ▼▲ to move to the Advanced menu and then press OK or ►. Press ▼▲ to move up and down in the Advanced menu. ITEM DESCRIPTION Color Space Press the cursor ◄► button to adjust the color space. Color Temperature Press the cursor ◄► button to adjust the color temperature. Color Manager Press OK / ► to enter the color manager menu. See page 32 for more information on Color Manager.
Color Manager Press OK / ► to enter the Color Manager sub menu. ITEM DESCRIPTION Red Select to enter the Red Color Manager. Press the ◄► buttons to adjust the Hue, Saturation, and Gain. Green Select to enter the Green Color Manager. Press the ◄► buttons to adjust the Hue, Saturation, and Gain. Blue Select to enter the Blue Color Manager. Press the ◄► buttons to adjust the Hue, Saturation, and Gain. Cyan Select to enter the Cyan Color Manager.
Computer Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Computer menu. Press the cursor ▲▼ button to move up and down in the computer menu. Press ◄► to change values for settings. ITEM DESCRIPTION Horizontal Position Press the cursor ◄► button to adjust the display position to left or right. Vertical Position Press the cursor ◄► button to adjust the display position to up or down. Tracking Press the cursor ◄► button to adjust the A/D sampling clock.
Video Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Video menu. Press the cursor ▲▼ button to move up and down in the Video menu. Press ◄► to change values for settings. ITEM DESCRIPTION Video AGC Press the ◄► buttons to enable or disable the Automatic Gain Control for video source. Video Saturation Press the ◄► buttons to adjust the video saturation. Video Tint Press the ◄► buttons to adjust the video tint/hue.
Audio Press OK / ► to enter the Audio sub menu. ITEM DESCRIPTION Volume Press the ◄► buttons to enter and adjust the audio volume. Mute Press the ◄► buttons to enter and turn on or off the speaker.
Installation I Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Installation I menu. Press the cursor ▲▼ button to move up and down in the Installation I menu. Press ◄► to change values for settings. ITEM DESCRIPTION Language Press the cursor ◄► button to select a different localization Menu. Blank Screen Press the cursor ◄► button to select different color to blank the screen.
Advanced Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Installation I menu. Press ▲▼ to move to the Advanced menu and then press OK or ►. Press ▲▼ to move up and down in the Advanced menu. Press ◄► to change values for setting. ITEM DESCRIPTION Security Lock Press the cursor ◄► button to enable or disable security lock function. Wall Color Press the cursor ◄► button to enable or disable wall color function.
Installation II Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Installation II menu. Press the cursor ▲▼ button to move up and down in the Installation II menu. ITEM DESCRIPTION Auto Search Press the cursor ◄► button to enable or disable automatic source detection. Auto Power Off (min.) Press the cursor ◄► button to enable or disable automatic shutdown of lamp when no signal.
Advanced Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Installation II menu. Press ▲▼ to move to the Advanced menu and then press OK or ►. Press ▲▼ to move up and down in the Advanced menu. Press ◄► to change values for setting. ITEM DESCRIPTION OSD Menu Setting Press OK / ► to enter the OSD setting menu. See page 40 for more information on OSD Menu Setting. Peripheral Test Press OK / ► to enter the Peripheral Test menu.
OSD Menu Setting ITEM DESCRIPTION Menu Position Press ◄► button to select different OSD location. Translucent Menu Press ◄► button to select OSD background translucent level. Menu Display Press ◄► button to select OSD timeout delay. Peripheral Test ITEM DESCRIPTION Remote Control Test Press OK / ► to test the IR remote controller for diagnostic. Color Test Press OK / ► to select different colors on screen. USB Test Press OK / ► to test the USB connection with connected PC.
Reset Lamp Time Please refer to Resetting the Lamp on page 54 to reset the lamp hour counter. 3D ITEM DESCRIPTION 3D Press ◄► to select Off, DLP-Link or IR. 3D Sync Invert Press ◄► to turn 3D Sync Invert On or Off. 3D Format Press ◄► to enable or disable 3D Format.
Network Setting ITEM DESCRIPTION Network State Displays the network connection status. DHCP Press ◄► to turn DHCP On or Off. Note: If you select DHCP Off, complete the IP Address, Subnet Mask, Gateway, and DNS fields. IP Address Enter a valid IP address if DHCP is turned off. Subnet Mask Enter a valid Subnet Mask if DHCP is turned off. Gateway Enter a valid Gateway address if DHCP is turned off. DNS Enter a valid DNS name if DHCP is turned off. Apply Press OK / ► to confirm settings.
For simplicity and ease of operation, the projector provides diverse networking and remote management features. The LAN/RJ45 function of the projector through a network, such as remotely manage: Power On/Off, Brightness and Contrast settings. Also, projector status information, such as: Video-Source, SoundMute, etc. The projector can be controlled by a PC (Laptop) or other external device with connecting to the projector's LAN/RJ45 port.
LAN RJ45 1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (Laptop). 2. On the PC (Laptop), select Start → Control Panel → Network and Internet.
3. Right-click on Local Area Connection, and select Properties. 4. In the Properties window, select the Networking tab, and select Internet Protocol (TCP/IP). 5. Click Properties.
6. Click Use the following IP address and fill in the IP address and Subnet mask, then click OK. 7. Press the Menu button on the projector. 8. Select Installation II → Advanced → Network Setting → Network State → Connect 9. After getting into Network Setting, input the following: DHCP: Off IP Address: 10. 10. 10. 10 Subnet Mask: 255.255.255.0 Gateway: 0.0.0.0 DNS Server: 0.0.0.0 10. Press OK / ► to confirm settings. 11.
CATEGORY Crestron Control Projector Network Configuration User Password Admin Password ITEM INPUT-LENGTH IP Address 15 IP ID 3 Port 5 Projector Name 10 Location 10 Assigned To 10 DHCP (Enabled) (N/A) IP Address 15 Subnet Mask 15 Default Gateway 15 DNS Server 15 Enabled (N/A) New Password 10 Confirm 10 Enabled (N/A) New Password 10 Confirm 10 For more information, please visit http://www.crestron.com/.
RS232 by Telnet Function Besides projector connected to RS232 interface with “Hyper-Terminal” communication by dedicated RS232 command control, there is alternative RS232 command control way, so called “RS232 by TELNET” for LAN/RJ45 interface. Quick Start-Guide for “RS232 by TELNET” Check and get the IP-Address on OSD of the projector. Make sure that laptop/PC can access the web-page of the projector.
Input the command format like the below: telnet ttt.xxx.yyy.zzz 23 (“Enter” key pressed) (ttt.xxx.yyy.zzz: IP-Address of the projector) If Telnet-Connection ready, and user can have RS232 command input, then “Enter” key pressed, the RS232 command will be workable. How to have TELNET enabled in Windows VISTA / 7 By default installation for Windows VISTA, “TELNET” function is not included. But end-user can have it by way of “Turn Windows features On or Off” to be enabled.
Select “Turn Windows features on or off” to open Have “Telnet Client” option checked, then press “OK” button. Specsheet for “RS232 by TELNET” : 1. Telnet: TCP 2. Telnet port: 23 3. Telnet utility: Windows “TELNET.exe” (console mode) 4. Disconnection for RS232-by-Telnet control normally: Close Windows Telnet utility directly after TELNET connection ready 5.
Factory Reset Press the cursor ▲▼ button to move up and down in the Installation II menu. Select the Factory Reset sub menu and press OK / ► to reset all the menu items to the factory default values (except Language and Security Lock). Status Press the cursor ▲▼ button to move up and down in the Installation II menu. Select the Status sub menu and press OK / ► to enter the Status sub menu. ITEM DESCRIPTION Active Source Display the activated source.
MAINTENANCE AND SECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be replaced with a certified replacement part, which you can order from your local dealer. parts No.LV-LP41 Warning: If illumination suddenly stops, either when you turn the projector on or after it has been on for a while, the lamp may have ruptured. In this case, never attempt to replace the lamp by yourself. Always request service from the Canon Customer Support Center.
2. Remove the lamp compartment cover. 3. Loosen the two screws securing the lamp. 4. Lift the module handle up. 5. Pull firmly on the module handle to remove the lamp. 6. Reverse steps 1 to 5 to install the new lamp. While installing, align the lamp module with the connector and ensure it is level to avoid damage. Note: The lamp must sit securely in place and the lamp connector must be connected properly before tightening the screws.
Resetting the Lamp Time After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following: 1. Press the MENU button to open the OSD menu. 2. Press the cursor ◄► button to move to the Installation II menu. Press the cursor button to move down to Advanced. 3. Press the cursor ▼▲ button to move down to Reset Lamp Time. 4. Press the cursor ► or Enter button. A message screen appears. 5. Press ▼▲◄► buttons to reset the lamp hour. 6.
Cleaning the Projector Cleaning the projector to remove dust and grime will help ensure trouble-free operation. Cleaning the Projector Mirror: When cleaning the projector’s lens, use a commonly available air blower or lens cleaning paper. The lens surface is easily damaged, so do not use a hard cloth or tissues. Caution: 1. Always turn the projector off and allow to cool for at least 30 minutes prior to cleaning. Caution: 1. Never touch the projector mirror or Lens directly by hand. 2.
Using the Physical Lock Using the Kensington® Lock If you are concerned about security, attach the projector to a permanent object with the Kensington slot and a security cable. Note: Contact your vendor for details on purchasing a suitable Kensington security cable. Using the Security Bar In addition to the password protection function and the Kensington lock, the Security Bar helps protect the projector from unauthorized removal. See the following picture.
TROUBLESHOOTING Tips for Troubleshooting In each problem-specific section, try the steps in the order suggested. This may help you to solve the problem more quickly. Try to pin point the problem and thus avoid replacing non-defective parts. For example, if you replace batteries and the problem remains, put the original batteries back and go to the next step.
LED Messages POWER LED GREEN LAMP LED AMBER TEMP LED RED Power On ON OFF OFF Power Off ON OFF OFF Flashing OFF OFF OFF OFF ON 4 blinks OFF OFF OFF ON OFF Fan 1 6 blinks 1 blinks OFF Fan 2 6 blinks 2 blinks OFF Fan 3 6 blinks 3 blinks OFF Fan 4 6 blinks 4 blinks OFF Lamp Door Open 7 blinks OFF OFF DMD error 8 blinks OFF OFF Color wheel error 9 blinks OFF OFF ERROR CODE MESSAGES Cooling Over Temperature Thermal Break Sensor error Lamp error In the event of
2. Adjust the Color Temperature settings on the Image->Advanced menu of the OSD. Lamp Problems Problem: There is no light from the projector 1. Check that the power cable is securely connected. 2. Ensure the power source is good by testing with another electrical device. 3. Restart the projector in the correct order and check that the Power LED is on. 4. If you have replaced the lamp recently, try resetting the lamp connections. 5. Replace the lamp. 6.
SPECIFICATIONS Product Specifications Model name LV-WX300UST / LV-WX300USTi Display system １ chip DLP system Optical system Time division color extraction, sequential display Display device Type DMD x1 Display Size / Aspect ratio 0.65 type / 16:10 device Number dots 1,024,000 (=Total number dots) Projection lens Operation Zoom: fixed, focus: manual Focal length / F 5.1 mm / 2.5 Projectio number Throw ratio 0.35:1 n lens Projection distance 60.5 - 70.
Installation Distance vs. Projection Size Installation Distance and Size Table WXGA 16:10 Diagonal 80" 87" 97" 100" Distance 282.3+/-20mm 340.3+/-20mm 421.4+/-20mm 445.8+/-20mm Image Width 1723mm 1874mm 2088mm 2154mm Image height 1077mm 1171mm 1305mm 1346mm 280+/-50mm 300.2+/-50mm 325.5+/-50mm 336.
Timing Mode Table The projector can display several resolutions. The following table outlines the resolutions that can be displayed by the projector.
HORIZONTAL SIGNAL Apple Macintosh SDTV EDTV HDTV RESOLUTION VERTICAL FREQUENCY FREQUENCY (KHZ) (HZ) 1440 x 900 1600 x1200 1680 x 1050 1680 x 1050 1920 x 1200 1920 x 1080 **** 1920 x 2205 640 x 480 832 x 624 1024 x 768 1152 x 870 480i 576i 576p 480p 720p 720p 1080i 1080i 1080p 1080p 1080p 1080p 1080p 70.6 75.0 64.7 65.3 74.0 67.5 — 35.0 49.7 60.2 68.7 15.734 15.625 31.3 31.5 37.5 45.0 33.8 28.1 27 28 33.7 67.5 56.3 75.0 60 59.9 60.0 60.0 60.0 23.97 66.7 74.5 74.9 75.1 60.0 50.0 50.0 60.0 50.0 60.
Projector Dimensions(LV-WX300UST) — 64—
122.6mm 374.
APPENDIX I Communication Baud rate: Data bit: Parity check: Stop bit: Flow Control 9600 8 None 1 None Control Command Structure The command is structured by the Header code, command code, data code and end code. Most of the commands are structured except some for the compatibility issue with other projectors. HEX ASCII Header code 7Eh ‘~’ Command code Command Command Data code Data Data End code 0Dh CR Command transfer using RS232(remote) and/or Network(LAN) does not available at power saver mode.
Remote Command The remote commands simulate the code send from IR remote handset.
Query Command ITEM Software Version Power State Input Select Lamp Hours Brightness Contrast Color (Video) Tint (Video) Scaling Color Temperature Projection Mode Sharpness Volume Freeze Status Mute Status Blank Status ASCII ~ q V CR ~ q P CR ~ q S CR ~ q L CR ~ q B CR ~ q C CR ~ q R CR ~ q N CR ~ q A CR ~ q T CR ~ q J CR ~ q H CR ~ q M CR ~ q Z CR ~ q U CR ~ q K CR HEX 7Eh 71h 56h 0Dh 7Eh 71h 50h 0Dh 7Eh 71h 53h 0Dh 7Eh 71h 4Ch 0Dh 7Eh 71h 42h 0Dh 7Eh 71h 43h 0Dh 7Eh 71h 52h 0Dh 7Eh 71h 4Eh 0Dh 7Eh 71h 41h
CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan U.S.A. CANON U.S.A. INC. One Canon Park, Melville, New York 11747, U.S.A. For all inquires concerning this product, call toll free in the U.S. 1-800-OK-CANON CANADA CANON CANADA INC. HEADQUARTERS 6390 Dixie Road, Mississauga, Ontario L5T 1P7, Canada CANON CANADA INC. MONTREAL BRANCH 5990, Côte-de-Liesse, Montréal Québec H4T 1V7, Canada CANON CANADA INC. CALGARY OFFICE 2828, 16th Street, N.E.
