PCV 604 C PCE 604 X FCO 404 X FCO 104 X FCO 104 N FCO 104 W BUILT-IN OVEN AND HOB USER'S MANUAL ENG
ENG Dear Installation
ENG Introduction of product and hob Transportation
ENG PART 1: INTRODUCTION OF PRODUCT MAIN PARTS Hob - Oven Combination Possibility FCO 104 W FCO 104 N FCO 104 X FCO 404 X PCV 604 C √ √ √ √ PCE 604 X √ √ √ √
ENG VITROCERAMIC HOB: PCV 604 C 4 1 1 o/ 145 Radiant Zone (1200W) 2 o/ 180 Radiant Zone (1700W) 3 Vitroceramic Surface 4 Lower Casing SOLID HOTPLATE HOB: PCE 604 X 5 4 1 1 o/ 145 Solid Hotplate Burners (1000W) 2 o/ 180 Solid Hotplate Burners (1500W) 3 ø 180 Rapid Solid Hotplate (2000W) 4 Cooktop 5 Lower Casing
ENG Kknobs power cord power cord power cord Kknobs 4
ENG Caution (Except model FCO404X): The heat vapour is given out through the ventilation holes at the handle during normal operation of the oven. Please kindly be aware of that usage .
ENG Iinstall Wworktop Figure 1
ENG 3.2 OVEN and HOB INSTALLATION Figure A- Flush Installation of Oven 510m m 580m m 40mm . Min m m 60 Wooden part 20mm Wooden part Min. 40mm Front frame Spacer Figure B- Regular Installation of Oven 510m m 580m m Mounting screw Wooden part 40mm .
ENG Installation steps: 1.Place the hob into the opening on worktop. The size of opening is given in Figure A. Fordetails, see the headings either Fixing the solid hotplate hob or Fixing the vitroceramic hob. 2.Connect the hob to the oven using the the plug given on the hob. The socket for plug is placed on the rear panel of oven. 3.Connect the oven to the electrical supply. 4.Place the oven into its built-in niche.
ENG worktop mounting bracket Fixing the oven: Insert the oven into cabinet partly by pushing it forward. Open the oven door and insert 4 screws into countersunk holes on the front frame. Locate the spacers behind the flange of front frame and screw them till the surface of spacer touches the front frame. While doing this, please pay attention that the chamfered edge of each spacer is faced to the rounded edge of front frame. Push forward the product completely and finally screw it to wooden part.
ENG 2 10 Power
ENG 4 2 WARNING: The cabling and wiring system must be. Able to bear the maximum electric power required by the oven. This is indicated on the rating plate oven. In case of any doubt please refer to professionals.
ENG 4.
ENG 4.2 USING THE COOKTOP BURNERS: T he hob part of the product is controlled via the 7-stage knob on the control . panel (Figure 3). Stage "0" means off position The remaining 6 stages indicate the following types of use: 1 1.........Heat Maintenance Position 2 - 3 ....Heatin g in Low Temperature Position 4-5-6 ...Cooking, Frying a nd Bo iling Position 6 2 5 3 4 Figure3 Burner control knob The u pper part of the Solid hotplate is cove red with a heat-resistant protective materia l.
ENG WARNINGS When a cooktop burner knob is brought to another position other than the ‘’0’’ position, the operation light will be on. Use only pots which fit the burner diameter. Before placing the pot on the burner, be sure that its bottom is not wet. Never operate a cooktop burner while empty. Pot temperature may be high when the appliance is in use. Therefore, it is recommended that you keep children and pets away from the hob both during and after operation.
ENG 4.3 USING THE OVEN: First, you need to adjust the oven function (see figure 4) and then set the oven temperature to desired value (see figure 5). Otherwise, the oven will not operate. When the temperature inside your oven reaches the value you set, the thermostat will cut the circuit and the thermostat light will go off. When the temperature falls below the set value, the thermostat will again be turned on and the thermostat light will be on.
ENG 4.4 FUNCTIONS: Availability of the functions explained below vary depending on the product mode l. Defrost Function : Yo u can start the d efrost oper ation b y p uttin g the fro ze n f ood into the oven and bringi ng the button to th e i ndicate d mark. This function does n ot cook/bake the fo od; it o nly he lps de fr ost it wi th in a sho rt ti me . P ut th e food to b e defrosted on the wire r ack that yo u wil l place on the thir d rack sup port fro m th e bo ttom ( Fi gure 6 ) .
ENG Fan and the Lower-Upper Heating Element Function (Static Cooking With Fan) : This is the position where the ai r coming from the lower a nd up per he ati ng el emen ts is circulated into the oven by the fan. Ad just the thermostat knob of your oven to a temperature recommended o n the cooking table for the cookin g operation you will perform.
ENG Turn your oven’s thermostat knob so it will point to this temperature value. After a preheating period of 5 minutes, put your foods into the oven. After the coo king, turn off the oven function control knob and the thermostat knob. Take the cooked/baked food out of the oven, place it on a safe place and ensure that th e oven completely cools off by keeping the oven door open. As the oven will be hot, stay away from the oven and keep your children away.
PART 5 : CLEANING AND MAINTENANCE ENG 5.1 GENERAL Before starting to clean your oven, be sure that all controL knobs are off and your appliance is cooled off. Unplug the appliance. Do not use cleaning materials containing particles that might scratch the enamelled and painted parts of your oven. Use cream cleaners or liquid cleaners, which do not contain particles. As they might harm the surfaces, do not use caustic creams, abrasive cleaning powders, rough wire wool or hard tools.
ENG Scrubbing with steel cleaning wires may harm the vitroceramic glass surface. Formations of dust on the surface should be cleaned up using a dampened . cloth. Changes in colour which might occur on the ceramic glass surface do not affect the functional structure or permanence of the vitroceramic.
PART 6 : SERVICE AND TRANSPORTATION ENG 6.1 REQUIREMENTS BEFORE CONTACTING TO SERVICE If the oven does not operate ; The oven may be plugged off, there has been a black out. If the oven does not heat ; The temperature may be not adjusted with oven’s temperature control switch. If the oven light does not operate does not light; The electricity should be controlled. It should be controlled whether the bul b is defective.
04.2007/R000 The symbol on the product or on its packaging indicates that this pro duct may not be treated as household waste. Instead it shall be hand ed over to the applicable collection point for the recycling of electrical and electronic equi pment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
