EN
Environmental conditions This appliance is marked according to the European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE). WEEE contains both polluting substances (which can cause negative consequences for the environment) and basic components (which can be re-used). It is important to have WEEE subjected to specific treatments, in order to remove and dispose properly all pollutants, and recover and recycle all materials.
in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. 1. GENERAL SAFETY RULES l This appliances is intended to be used in household and similar applications such as: - Staff kitchen areas in shops, offices and other working environments; - Farm houses; - By clients in hotels, motels and other residential type environments; - Bed and breakfast type environments.
final part of a washer dryer l Items that have been soiled with cycle occurs without heat (cool substances such as cooking oil, down cycle) to ensure that the acetone, alcohol, petrol, kerosene, items are left at a temperature spot removers, turpentine, waxes that ensures that the items will and wax removers should be not be damaged. washed in hot water with an extra amount of detergent before being dried in the washer dryer.
by hair care products be l Do not pull on the power cord placed in a washer dryer they or appliance to unplug the should first be washed in hot machine. water with extra detergent this will reduce, but not l Do not expose the washing machine to rain, direct sunlight eliminate, the hazard. or other weather elements. l Remove all objects from Protect from possible freezing. pockets such as lighters and l When moving, do not lift the matches.
l Release the power chord and drain hose from the securing clip at the rear of the machine. l Remove the 2 or 4 transportation screws (A) on the back and remove the 2 or 4 flat washers, rubber bungs and plastic spacer tubes (B) as illustrated in figure 1. l If the washing machine is built-in, unscrew the 3 or 4 transportation screws (A) and remove the 3 or 4 flat washers, rubber bungs and plastic spacer tubes (B).
Instructions for mounting the furniture door l Position the template onto the reverse of the furniture door. It is possible to mount the hinges and closure magnet on the right or left-hand side depending on your requirements. Mark the screw hole positions, then drill out these positions. B C A l Fix the hinges in place with the 4 screws provided (A). l Fix the magnet (B) in place using screw (C).
the furniture door to the front of the washer using the hinges. Place the spacers under the hinges (I) and then fix in position with screw (H). EN l Mount H I We suggest mounting the furniture door so that it opens towards the left, which is the same direction as the porthole door. This will leave more space when you are loading washing into the appliance. l Slide the washer into an opening of the size indicated in the diagram opposite.
Hydraulic connections 3 l Connect the water hose to the water supply tap (fig. 3) only using the hose supplied with the appliance (do not reuse old hose-sets). l Some models may include one or more of the following features: l HOT&COLD (fig. 4): water mains connection settings with hot and cold water for higher energy savings. Connect the grey tube to the cold water tap and the red one to the hot water tap.
illustrated in figure 8: a. turn the nut clockwise to release the screw; b. rotate the foot to raise or lower it until it touches to the floor; c. lock the foot, screwing in the nut, until it tightens against to the bottom of the washing machine. l Plug in the appliance. 8 EN l Level the appliance using the feet as A B WARNING: contact the Customer Service Centre should the power cord need replacement.
reduce the necessity of a hot wash programme. Save energy by using a low temperature wash programme. 3.
finished, replace it turning it clockwise. The filter handle will be locked when it is not possible to turn any further and the handle is horizontal. Smearing a small amount of liquid soap on the filter seal will help refitting. To clean the washing machine exterior, use a damp cloth, avoiding abrasives, alcohol and/or solvents. To maintain a good wash performance we recommend that the soap drawer and pump filters are regularly cleaned.
5. QUICK USER GUIDE This washing machine automatically adjusts the level of the water to the type and quantity of washing. This system gives a reduction in energy consumption and a saving in washing times. 6. CONTROLS AND PROGRAMS A Program selection l Turn on the washing machine and select the required program. l Adjust the washing temperature if necessary and press the required "option" buttons.
When the START/PAUSE button has been pressed, the appliance can take few seconds before it starts working. When the programme selector is turned the display lights up to show the settings for the programme selected. For energy saving, at the end of the cycle or with an inactivity period, the display level contrast will decrease.
- Press the delay start button once to activate it (h00 appears on the display) and then press it again to set a 1 hour delay (h01 appears on the display). The pre-set delay increases by 1 hour each time the button is pressed, until h24 appears on the display, at which point pressing the button again will reset the delay start to zero. - Confirm by pressing the START/PAUSE button. The delay countdown will begin and when it has finished the programme will start automatically.
To prevent damage to the fabrics, it is not possible to increase the speed over the maximum allowed for the programme. This button allows you to choose between two different options, depending on the selected programme. - RAPID l To reactivate the spin cycle press the button until you reach the spin speed you would like to set. The button becomes active when you select the RAPID (14/30/44 Min.) programme on the knob and allows you to select one of three durations indicated.
3) DOOR LOCKED INDICATOR LIGHT Digital Display l The indicator light is illuminated when the The display’s indicator system allows you to be constantly informed about the status of the machine. 1 2 3 4 6 door is fully closed. Close the door BEFORE selecting the START/PAUSE button. 7 l When START/PAUSE is pressed on the machine with the door closed, the indicator will flash momentarily and then illuminate.
6) WASH TEMPERATURE LIGHTS - recognises the presence of too much soap suds, and if necessary, adjust the amount of rinse water. This shows the washing temperature of the selected programme that can be changed (where allowed) by the relevant button. If you want carry out a cold wash all the indicators must be off. - adjusts the spin speed according to the load, thus avoiding any imbalance.
Table of programmes 1) (MAX.) * 2 (see control panel) PROGRAMME (MAX.
INFORMATION FOR THE LABORATORIES (Ref. EN Standards) Washing (Only for models with liquid detergent compartment) When only a limited number of articles have stains which require treatment with liquid bleaching agents, preliminary removal of stain can be carried out in the washing machine. Pour the bleach into the liquid bleach container, inserted into the compartment marked "2" in the detergent drawer, and set the special programme RINSE.
Programmes selection To clean different types of fabrics and various levels of dirt, the washing machine has specific programs to meet every need of washing (see table of programmes). WASHING Whites An intensive wash. The final spin at maximum speed gives more efficient removal. Cottons This program is suitable to clean normally soiled cotton laundry and it is the most efficient program in terms of combined energy and water consumptions for washing cotton laundry. Rapid (14/30/44 Min.
EN DRYING WARNING: Dispensers used for concentrated powders and liquid detergents must be removed from the drum before commencing the tumble drying programmes. The wool drying cycle of this machine has been approved by "The Woolmark Company" for the drying of machine washable wool products provided that the products are washed and dried according to the instructions on the garment label and those issues by the manufacturer of this machine.
7. DRYING CYCLE The correct way to dry l Drying guidance advice is general, but practical experience of using the product will help you to achieve the best drying results. l We recommend setting a lower drying time than indicated, when first using the appliance in order to establish the degree of dryness required. l We recommend not drying fabrics that fray easily, such as rugs or garments with a deep pile, in order to avoid air duct clogging.
l Switch off the machine by turning the By selecting the wool drying programme, it's not possible to select a degree of dryness different from the default one. l Open the door and remove the laundry. l Turn off the tap. l The washer dryer will calculate the time CANCELLING THE DRYING PROGRAMME needed for drying and the level of moisture remaining in the laundry, according to the load and drying type selected.
l At the end of the wash phase the display 8. AUTOMATIC WASHING/DRYING CYCLE will show the drying time remaining. l When the programme is finished the word "End" will appear on the display. After 5 minutes the appliance will go into standby mode (on certain models, the display will show two lines). You cannot exceed the maximum dryable load of laundry indicated in the programme table, otherwise the laundry will not be dried satisfactory.
If you believe the washing machine is not working correctly, consult the quick guide provided below which includes some practical tips on how to fix the most common problems. FOR SMART TOUCH MODELS The Candy simply-Fi app has a Smart Check-up function that allows you to confirm the functionality and status of the product at any time. To use the Candy simply-Fi app you will need an Android smartphone with NFC technology. More info can be found on the App.
OTHER ANOMALIES Problem Possible causes and practical solutions The washing machine does not work / start The washing machine does not spin Make sure the product is plugged into a working supply socket. Make sure power is on. Make sure the wall socket is working, testing it with another appliance such as a lamp. The door may not be correctly closed: open and close it again. Check whether the required program was correctly selected and the start button pressed.
- cloudier rinse drain water: This effect is tied to the suspended zeolites which do not have negative effects on rinse efficiency. If the problem persists or if you suspect a malfunction, immediately contact an Authorised Customer Service Centre. It is always recommended to use original spare parts, that are available at our Authorised Customer Service Centres. - white powder (zeolites) on laundry at the end of the wash: this is normal, the powder is not absorbed by fabric and does not change its colour.
fkhldsk
fkhldsk
- CBWD D - 18.