CBP613NGR/S Cooker Hood Instruction Manual 1
Content Safetyinstructions…………………………………..…………………………………………………3 Installation…………………………………..…………………………………………………………….5 Startusingyourcookerhood…………………………………..………………………………..9 Troubleshooting…………………………………..……………………………………………………10 Maintenanceandcleaning…………………………………..……………………………………11 Environmentprotection…………………………………..………………………………………..
SAFETY INSTRUCTIONS Thismanualexplainstheproperinstallationanduseofyourcookerhood, pleasereaditcarefullybeforeusingevenifyouarefamiliarwiththeproduct. Themanualshouldbekeptinasafeplaceforfuturereference. Nevertodo: Alwaystodo: ● Do not try to use the cooker hood without the grease filters or if the filters are excessively greasy! ●Do not install above a cooker with a high level grill.
Alwaystodo: Alwaystodo: ●Always put lids on pots and pans when cooking on a gas cooker. ●When in extraction mode, air in the room is being removed by the cooker hood. Please make sure that proper ventilation measures are being observed. The cooker hood removes odours from room but not steam. ●Cooker hood is for domestic use only. ● Caution: The appliance and its accessible parts can become hot during operation. Be careful to avoid touching the heating elements.
INSTALLATION (VENT OUTSIDE) If you have an outlet to the outside, your cooker hood can be connected as below picture by means of an extraction duct (enamel, aluminum, flexible pipe or nonflammable material with an interior diameter of 120mm) 1. Before installation, turn the unit off and unplug it from the outlet. 2. The cooker hood should be placed at a height of 65-75cm above the cooking surface for best efficiency. 65cm 75cm 3. Install the cooker hood between two cupboards.
4. Hang the cooker hood on the screws between the two cupboards. 5. Push the fan-shaped door frames to the end, in order to make the outer edges of the door frames at the same vertical level as the outer edge of the cupboards. 6. Mark the positions where you install the lower screws. Drill the upper hole and fix the screws. Make sure all four screws are well fixed. 600 7.
8. Connect the air-outlet board and the air-outlet tube (Vent Hose) which will need to feed through to the outside of the building. Rigid kits, if preferred, can be obtained from either the retailer who supplied the hood, or DIY Stores and Builders Merchants. 9. Door installation: The door should be no less than 16mm thick, 385-700mm high, and weigh no more than 7KG. Pull out the movable fan-shaped door frames by the plastic handle, and place the fan-shaped door frames one on left and one on right.
12. The two screws on both sides of the cooker hood can adjust the sliding of the door, according to the weight of the door. 13. Install the adjusting plate, in order to cover the gap between the wall and the bottom of the cooker hood.
Electrical Installation All installation must be carried out by a competent person or qualified electrician. Before connecting the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate. Direct Connection The appliance must be connected directly to the mains using an omnipolar circuit breaker with a minimum opening of 3mm between the contacts. The installer must ensure that the correct electrical connection has been made and that it complies with the wiring diagram.
To operate: pull up the front panel, turn on the cooker hood, and then choose the fan speed setting. To turn the unit off, there are two options: 1. Turn off the fan with the slide switch. 2. Push down the front panel (with the fan still switched on). This will turn the hood off, and when the cooker hood is next opened, the fan speed will be the same as the last time it was operate. 3. Whether the front panel is open or not, or the fan in use or not, the light can be operated independently.
The Cooker hood inclines The fixing screw is not tight enough Tighten the hanging screw and make it horizontal. NOTE: Any electrical repairs to this appliance must conform to your local, state and federal laws.Please contact the service centre if in any doubt before undertaking any of the above. Always disconnect the unit from the power source when opening the unit.
Filters should be washed separately to crockery and kitchen utensils. It is advisable not to use rinse aid. Remove the filter as shown in the diagrams below: 1. 1 2 2. INSTALLING GREASE MESH FILTERS • To install filters for the following four steps . - Angle the filter into slots at the back of the hood. - Push the button on handle of the filter. - Release the handle once the filter fits into a resting position. - Repeat to install all filters.
BULB REPLACEMENT Important : The bulb must be replaced by the manufacturer, its service agent or similarly qualified persons. Always switch off the electricity supply before carrying out any operations on the appliance. When handling bulb, make sure it has completely cooled down before any direct contact to hands. When handling blubs hold with a cloth or gloves to ensure perspiration does not come in contact with the blub as this can reduce the life of the blub.
ENVIRONMENTAL PROTECTION: This product is marked with the symbol on the selective sorting of waste electronic equipment. This means that this product must not be disposed of with household waste but must be supported by a system of selective collection in accordance with Directive 2012/19/EU.