User's Guide

ManualsBrandsCandibell ManualsElectronicsCandibell Truthbrush

Truthbrush Tracker & Hub

User Guide

Truthbrush Tracker FCC ID: 2AS6G-T1

Truthbrush Hub: Contains FCC ID 2AC7Z-ESPWROOM32D

Truthbrush Tracker

The Truthbrush tracker is a small, decorative, device that can be placed on any manual or electric

toothbrush. It is designed to monitor brushing activity and to identify patterns that can be improved.

The device starts to monitor when picked up and stops when placed back down. The activity data is

recorded and analyzed to determine the brush time, duration, and coverage. Users can view brush

information for their family in the Truthbrush mobile application and can share the data with their

dentist. A Truthbrush Hub is required and is sold separately.

Control button

The control button is used to start the tracker and connect it to the Truthbrush mobile application.

Turn on Tracker

Press and hold on the top of the sensor for 1 second to turn the tracker on. The single press is used to

make the tracker wirelessly discoverable to the Truthbrush mobile application. You will hear a single,

solid beep lasting for 1 second.

This device complies with Part 15 of the FCC rules. Operation is subject to the

following two conditions: 1) this device may not cause harmful interference, and 2)

this device must accept any interference received, including interference that may

cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

--Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

FCC Radiation Exposure Statement

This device complies with FCC RF radiation exposure limits set forth for an

uncontrolled environment. This transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

FCC Compliance Statement

Summary of content (5 pages)

PAGE 1
Truthbrush Tracker & Hub User Guide FCC Compliance Statement This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
PAGE 2
Making Tracker Discoverable After It was previously turned on Sometime the tracker needs to be put into discoverable mode after it has been previously turned on. For example, then the tracker needs to be configured for a different owner. To do this, quickly double press on the top of the tracker. A single, solid beep lasting for 1 second can be heard. Turning Tracker Off To turn off tracker completely, quickly press the tracker’s button for 6 times. You will hear it beeps quickly for 5-6 times.
PAGE 3
Setup Your Truthbrush The tracker can be used with any manual or electric toothbrush. It can be transferred from one toothbrush to another and is associated to a specific user profile. The following instructions are used to setup the tracker: Attach Tracker to Toothbrush Slip the Truthbrush tracker onto the desired toothbrush. The band will stretch to fit. The tracker should be placed facing forward with the design right side up.
PAGE 4
for users that are not brushing for 2 minutes and work up. Operate Your Truthbrush Data Collection The Truthbrush tracker works automatically and begins monitoring when the user lifts the toothbrush for use. There is no need to remember to start tracking or connect the device to a mobile phone. The tracker works seamlessly with the Truthbrush hub to collect all data accurately and reliably. All tracker activity data is sent and analyzed in real-time by the Truthbrush service.
PAGE 5
Brush detail Users can view the detail of individual brush sessions including the actual brush duration, brush coverage, and motion analysis. Candibell Truthbrush™. ©2020. Candibell Inc. All Rights Reserved. Registered Trademark. Patent Pending. Visit our website for more information: https://www.truthbrush.