TOP Plus Dach-Flachantenne mit kompakter Dreheinheit Zusatz Montage- und Bedienungsanleitung www.camos-multimedia.
1. Inhalt der Verpackung: Anzahl 1 1 2 1 1 1 1 1 1 1 1 1 1 Beschreibung Antenne Camos Top Plus mit Halterung Dreheinheit (vormontiert) Stabilisierungsplatten (1Haupt- und 1 Zusatzplatte) Grundplatte Handrad Kurbel Feder Gleitring Skalenscheibe Antennenkabel 5m einseitig mit F-Stecker F-Stecker Gel-Kappe Dachdurchführung Kompass Schrauben 2.
. Vorbereitung der Installation Suchen Sie eine geeignete Stelle auf dem Fahrzeugdach aus. Idealerweise sollte die Antenne in alle Richtungen frei drehbar sein, und in keiner Position durch andere Dachaufbauten abgeschattet werden. Achten Sie darauf, dass diese Stelle auch im Innenraum frei zugänglich ist und keine Lampen, Kabel oder Einbauten beim Durchbohren des Daches beschädigt werden.
. Montage der Dreheinheit Schneiden Sie mit der Lochsäge ein Loch von 38mm in das Dach. Tragen Sie auf der Unterseite der Dreheinheit jeweils um den Mittelzapfen herum und entlang der Außenkante der Dreheinheit einen ca. 0,5 cm dicken Strang Sikaflex®. Befolgen Sie dabei die Anweisungen des Herstellers mit Hinsicht auf die Vorbereitung der Oberfläche, das Auftragen und das Aushärten.
Befestigen Sie nun die Antenne mit vormontierter Halterung an der Dreheinheit mittels der 3 beigefügten Schrauben mit Muttern (M5x62mm). 5. Anschließen der Antenne Schließen Sie das Kabel mit dem F-Stecker an die Antenne an. Führen Sie das Kabel durch die seitliche Öffnung in der Dreheinheit, dann durch die hintere Öffnung der Dachdurchführung (s.Abb.1). Die Länge des Antennenkabels zwischen Dachdurchführung und Antenne sollte ca. 70cm (siehe Markierung) betragen.
Ebenfalls auf der Scheibe finden Sie die Position der einzelnen Satelliten. Ermitteln Sie mit Hilfe des beigelegten Kompasses Norden. Drehen Sie die Skalenscheibe mit der Kennzeichnung N nach Norden. Das Handrad wird nun mit der Zeigerspitze in den Bereich des gewünschten Satelliten gedreht. Drehen Sie das Handrad innerhalb des markierten Bereiches langsam weiter, bis Sie Ihr gewünschtes Fernsehprogramm empfangen. Achtung: Versuchen Sie auf keinen Fall, die Antenne über einen Widerstand hinaus zu drehen.
. Umlegen der Antenne: Drehen Sie die Antenne mit dem Handrad so, dass die Zeigerspitze der Grundplatte mit der Zeigerspitze des Handrades übereinstimmen. Sollten Sie während der Drehung des Handrades einen Widerstand spüren, drehen Sie bitte in die entgegengesetzte Richtung, um das äußere Antennenkabel nicht zu beschädigen. Erst wenn beide Zeigerspitzen übereinander stehen darf die Antenne mit der Handkurbel in die Ruheposition gebracht werden.
IMC GmbH Nikolaus-Otto-Str. 16 22946 Trittau Tel.: 04154-7093202-0 Fax: 04154-7093202-20 info@imc-multimedia.
TOP Plus Satellite Flat Antenna with Lift and Rotation Unit Manual www.camos-multimedia.
5. Contents: Quantity 1 1 2 1 1 1 1 1 1 1 1 1 1 Description Antenna Camos Top Plus Lift and Rotation Unit (pre-assembled) Ceiling Support plates Ceiling plate Rotation handle Elevation handle Spring Washer Graduation disc Antenna cable 5m one side with F-series connector F-connector Protector Gel Cable entry box Screws 6.
7. Installation Planning Decide where you wish to mount your satellite system. Location of the lift assembly must allow antenna to point towards the rear of the vehicle when resting in the travel position, and must clear all roof mounted equipment when being raised, lowered or rotated. The inside ceiling must be clear of obstructions to ceiling plate and handle. Before drilling, check for cables or obstructions within the roof space.
8. Mounting Using a 38mm diameter hole saw, cut a hole through the roof and ceiling for the centre shaft. Apply a layer of approx. 0,5 cm thick of adhesive such as Sikaflex® on the bottom of the base plate. Follow the manufacturer’s guidelines for surface preparation, application and curing. Insert the crankshaft with square tube into the hole, then position and attach the lift assembly to the roof with the enclosed self-cutting tapping screws. Measure the thickness of the roof.
5. Connecting the Antenna Connect the coaxial cable to the antenna and tighten. Feed the cable sidewise through the lift assembly, then insert cable through gland in rear of roof entry box and push cable into vehicle. Leave 70 cm of cable (see indication) from antenna to roof entry. Following glue on the cable entry box to the roof (e.g. with Sikaflex®). Route cable to satellite receiver and fit ‘F’ connector. Connect to the connector marked "SATELLITE IN" on the rear of the satellite receiver. 6.
The graduation disc also will be used to indicate the approximate direction and position of the desired satellite. With the enclosed compass find out the direction north and turn the Indicator "N" into this direction. Turn the indicator of rotation handle into the area of desired satellite, which appears highlighted in colour on the graduation disc. Turn the rotation handle slowly inside this area, until you receive the desired TV-channel. Note: Stop rotating the antenna if you notice a resistance.
7. To Lower Antenna: Pull rotation handle down to disengage gear from ceiling plate and rotate the antenna until the pointer on the ceiling plate is aligned with the pointer on the rotation handle. Rotate elevation handle counter clockwise until you hear the antenna touch the roof (resistance will be felt in the handle). If you notice resistance during rotation (the antenna cable maybe winded around the unit), turn into contrary direction.
IMC GmbH (Camos Europe) Nikolaus-Otto-Str. 16 22946 Trittau Tel 04154 / 7093202 - 0 www.camos-multimedia.com info@camos-multimedia.