2.4GHz/5GHz Dual-Band USB 2.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz – 300GHz) EN 301 893 V1.4.1: (2007-07) Broadband Radio Access Networks (BRAN); 5 GHz high performance RLAN; Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive EN 300 328 V1.7.
[Greek] ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/ΕΚ. Français [French] Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano [Italian] Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
TABLE OF CONTENT Introduction................................................................................................1 Overview of this User’s Guide .................................................................................1 Unpacking and Setup .................................................................................2 Unpacking .................................................................................................................2 Setup......................................
INTRODUCTION Congratulations on your purchase of this IEEE 802.11a/b/g/n 2.4GHz/5GHz DualBand Wireless LAN USB 2.0 Adapter. This manual contains detailed instructions regarding the operation of this product. Please keep this manual for future reference. With the IEEE 802.11a/b/g/n 2.4GHz/5GHz Dual-Band Wireless LAN USB 2.0 Adapter, a desktop or laptop computer can communicate with another computer wirelessly.
UNPACKING AND SETUP This section provides unpacking and setup information for the IEEE 802.11a/b/g/n 2.4GHz/5GHz Dual-Band Wireless LAN USB 2.0 Adapter. Unpacking The box should contain the following items: One the IEEE 802.11a/b/g/n 2.4GHz/5GHz Dual-Band Wireless LAN USB Adapter One Driver & Utility CD-ROM If any item is found missing or damaged, please contact your local reseller for replacement.
IDENTIFYING EXTERNAL COMPONENTS LED When the LED is blinking, the WLAN Adapter is transmitting or receiving data on the Wireless Ethernet network. Check the installation The LED of the IEEE 802.11a/b/g/n 2.4GHz/5GHz Dual-Band Wireless LAN USB 2.0 Adapter is clearly visible and the status of the network link can be seen instantly: 1.
SOFTWARE INSTALLATION This section describes how to install the driver and utility for the IEEE 802.11a/b/g/n 2.4GHz/5GHz Dual-Band Wireless LAN USB 2.0 Adapter. Windows Based Utility Installation 1) Insert the Utility and Driver CD-ROM into your computer’s CD-ROM Drive and then clicks Install Utility.
3) Click Finish to restart the computer. 4) Plug the IEEE 802.11a/b/g/n 2.4GHz/5GHz Dual-Band Wireless LAN USB 2.0 Adapter into an available USB slot on your computer.
WIRELESS UTILITY SETTING The user can configure the wireless settings using the Wireless Adapter Configuration Utility. Double-click the utility icon that appears in the taskbar. The Wireless Adapter Configuration Utility is divided into six sections: Link Info, Configuration, Site Survey, Profile, WPS and About. Link Information This is the default screen after launching the Utility program. Status: Shows the associated BSSID, which can be used to identify the wireless access point.
Link Quality: Shows the link quality of the IEEE 802.11a/b/g/n 2.4GHz/5GHz Dual-Band Wireless LAN USB 2.0 Adapter with the Access Point when operating under Infrastructure mode. Signal Strength: Shows the wireless signal strength of the connection between the IEEE 802.11a/b/g/n 2.4GHz/5GHz Dual-Band Wireless LAN USB 2.0 Adapter with the Access Point. Data Rate: Shows the statistics of data transfer, and the calculation is based on the number of packets transmitted and received.
Wireless Mode: There are two modes available for selection ● Infrastructure – to establish wireless communication with the LAN and other wireless clients through the use of Access Points. ● Ad-Hoc – to establish point-to-point wireless communication directly with other wireless client devices. Authtication: The following options are available: Open System, Shared Key, WPA-PSK, WPA2-PSK, WPA EAP-TLS, WPA2 EPA-TLS . Select Open System, Shared Key for WEP data encryption feature.
WPA-PSK / WPA2-PSK If using the WPA-PSK/WPA2-PSK authentication method, please select the Encryption type for TKIP or AES then enter the Passphrase key. The minimum length is 8 characters. WPA EAP-TLS If using the WPA/WPA2 EAP-TLS authentication method, please select the Encryption type for TKIP or AES then select the WPA/WPA2 Certificate from drop down list.
Site Survey This screen allows the user to scan for available wireless networks (wireless clients and Access Points). It also allows the user to establish wireless communications with an available wireless network. Available Network – displays the wireless networks (wireless clients and access points) that are within range. Select any one of the wireless networks by double-clicking on it or clicking on the “Connect” button. Click the “Refresh” button to scan for available networks.
Profile Profile – The user can create and manage the created profiles for home, work or public areas. By double-clicking on one of the created profile, the setting will adjust to the specific setting such as SSID, channel, and encryption as saved by that particular profile. Add: Adds a profile. The following screen will appear. The user can enter the necessary information required for accessing Access Points or Wireless Router Remove: Deletes the selected profile Edit: Edit an exist profile.
WPS WiFi Protected Setup (WPS) is an optional certification program from the Wi-Fi Alliance that is designed to ease the task of setting up and configuring security on a wireless network. There are two methods used in the WPS as below instruction. Push the button on my access point Using the WPS configuration with the “Push the button on my access point” method, the configuration steps as below: 1) Selected the “Push the button on my access point”.
4) If the WPS configuration was successful, the follow window will show on. 5) If the WPS configuration was failed, the follow window will show on.
Enter a PIN into my access point Using the WPS configuration with the “Enter a PIN into my access point” method, the configuration steps as below: 1) Selected the “Enter a PIN into my access point”, the PIN will be show on the button of the windows. 2) Enter the PIN code into the WPS “Clint PIN number” of you wireless access point or router then click the Start PIN button, the wireless access point or router will start the WPS configuration process.
4) If the WPS configuration was successful, the follow window will show on. 5) If the WPS configuration was failed, the follow window will show on.
About This screen displays information about the IEEE 802.11a/b/g/n 2.4GHz/5GHz Dual-Band Wireless LAN USB 2.0 Adapter, such as the Driver and Utility version. When a new version of the utility becomes available for upgrade, users will be able to identify by version numbers.
TECHNICAL SPECIFICATIONS Hardware Interface USB 2.0 Compliant Standards IEEE 802.11n draft v2.0, IEEE 802.11a, IEEE 802.11b and IEEE 802.11g Antenna Internal two high performance Antenna LED Indicator Activity Supported OS Windows 2000, XP and Vista Dimensions (LxWxH) 86.5 x 30 x 13 mm Temperature Operating: 0° ~ 40° C (32° ~ 104° F) Storage: -10° ~ 70° C (14° ~ 158° F) Humidity 10% ~ 95% max (Non-condensing) Certification FCC Part 15.
