DSLR-2001N 802.
Table of Contents Chapter 1: Product Overview...................................... 6 1.1 Features ................................................... 6 1.2 Package Contents ........................................... 7 1.3 Hardware Overview .......................................... 8 Front Panel ............................................. 8 Rear Panel ............................................. 10 1.4 Wireless Considerations ................................... 11 Connection Performance ...............
5.3 Local Network ............................................. 41 LAN .................................................... 41 DHCP Setting ........................................... 42 DHCP Reserved Address .................................. 43 5.4 Time and Date ............................................. 44 Chapter 6: Advanced............................................. 46 6.1 Advanced Wireless ......................................... 46 Wireless Router Settings ...............................
6.9 Static Route .............................................. 67 6.10 Multicast ................................................ 69 6.11 Dynamic DNS .............................................. 70 6.12 Ethernet Setting ......................................... 71 6.13 Port Mapping ............................................. 72 6.14 Quality of Service (QoS) ................................. 74 Queue Management ....................................... 74 Queue Config .....................................
Statistics > DSL Statistics ........................... 100 Appendix....................................................... 101 A. Regulatory & Safety Information ........................... 101 Wireless LAN, Health and Authorization ................ 101 Disclaimers ........................................... 101 FCC (Federal Communications Commission) Statement ..... 102 CE statement .......................................... 105 B. Specifications ............................................ 109 C.
Product Overview Chapter 1: Product Overview Thank you for choosing Trendnet Wireless N ADSL2 Modem Router. This Modem Router combines the functionality of an ADSL modem and Internet gateway in one. It allows you to access the Internet and share resources such as printers, scanners, and files, via a wireless connection or through one of the Ethernet ports. The various security features, such as WPS, WPA2, SPI, and NAT, protect your data and privacy online.
Product Overview 1.2 Package Contents Check if your package contains the following items. If any item is missing or appears damaged, contact your dealer.
Product Overview 1.3 Hardware Overview Front Panel 1 No. LED 2 3 4 5 6 Description Lights up when the device is powered on. • 1 Power LED Solid GREEN – Indicates normal operation. • Solid RED – Indicates malfunction. • Off – The device is powered off. Lights up when a computer is connected on the Ethernet ports (1~4). 2 LAN 1, 2, 3, 4 • 3 Wireless Solid GREEN – Connected but no activity. • Flashing GREEN – Data transmission is in progress. • Off – No computer is connected.
Product Overview No. LED Description Lights up to indicate the Wireless Protected Setup (WPS) connection status. • 4 WPS 5 DSL Solid GREEN – WPS-enabled device is connected. • Flashing GREEN – Searching for WPS-enabled devices. • Solid RED – No WPS-enabled device is connected. • Off – WPS is disabled. Lights up to indicate DSL connection status. • Flashing GREEN – Attempts to synchronize with DSL line. • Solid GREEN – DSL line is synchronized. • Off – DSL connection is not present.
Product Overview Rear Panel 1 2 3 4 5 6 No. Ports / Buttons Description 1 DSL port Connects to the DSL line using the RJ-11 cable. 2 WPS button Press to search for devices that support Wi-Fi Protected Setup (WPS). 3 Reset button Press and hold this button for 5 seconds to restore your device to its original factory default setting. 4 Ethernet port Connects a computer and other Ethernet network devices to the Modem Router using RJ-45 cables.
Product Overview 1.4 Wireless Considerations Connection Performance A number of factors affect the performance of wireless connection. Consider the following guidelines to ensure high-range and stable connectivity. 1. Keep the Modem Router and other wireless devices away from obstructions, such as walls or buildings. Each obstruction can reduce the range of a wireless device. 2.
Product Overview Your device supports Wired Equivalent Privacy (WEP), and WiFi Protected Access (WAP/WPA2) encryption. To ensure a high level of security, enable the highest security encryption and use strong passphrases, avoid using words that can be found in the dictionary.
Installation Chapter 2: Installation Make sure that all devices are powered off before starting installation. Installation Diagram 2.1 Connect the Power 1. Connect the power adapter to the power port of your Modem Router. 2. Plug the power adapter to a wall outlet or a power strip. ☞ NOTE: • • Use only the supplied power adapter. Using other power adapters may cause damage to the device. Connect all devices to your Modem Router before connecting the power adapter to a wall outlet.
Installation 2.2 Connect the Computer Wired Connection 1. Connect one end of the RJ-45 cable to one of the Ethernet (1, 2, 3, 4) ports of your Modem Router. 2. Connect the other end of the RJ-45 cable to the Ethernet port of the computer. Repeat the above steps to connect other computers to the Modem Router via Ethernet connection. To connect more than four computers, use a hub or switch. Connect one end of an RJ-45 cable to the hub or switch and the other end to the computer. 2.3 Connect the DSL 1.
Installation 4. Connect the telephone to the LINE port of the splitter using another RJ-11 cable. 2.4 Check the Installation To ensure that all devices are properly connected, check the LED indicators on the front of your Modem Router. For basic installation, the following LED must be lit: √ Power LED √ LAN LED (for every computer that is connected via Ethernet connection) √ DSL LED The lighted LED indicators vary depending on the type of connection that you make.
Configure the Computer Chapter 3: Configure the Computer This chapter will guide you on how to configure your computer according to the operating system you are using. • Windows 95 / 98 / ME, see below. • Windows 2000, see page 17. • Windows XP, see page 18. • Windows Vista, see page 19. • Windows 7, see page 19. 3.1 Windows 95 / 98 / ME If you are using Windows 95 / 98 / ME operating system, follow the instructions below to configure your computer. 1.
Configure the Computer IP Address Page DNS Configuration Page Gateway Page 3.2 Windows 2000 If you are using Windows 2000, follow the instructions below to configure your computer.
Configure the Computer 1. Click Start > Settings > Control Panel > Network and Dial-up Connections. 2. Double-click Local Area Connection. 3. Click Properties. 4. On the network components list, make sure that Internet Protocol (TCP/IP) is checked. If not, check it to enable the Properties button. 5. Select Internet Protocol (TCP/IP), and then click Properties. 6. On the General tab, select Obtain an IP Address automatically and Obtain DNS server address automatically. General Page 7. Click OK. 3.
Configure the Computer 3.4 Windows Vista If you are using Windows Vista, follow the instructions below to configure your computer. 1. Click Start > Control Panel > Network and Internet Connections > Network Connections. 2. Right-click Local Area Connection, then click Properties. 3. On the General tab, make sure that Internet Protocol (TCP/IP) is checked. If not, check it to enable the Properties button. 4. Select Internet Protocol (TCP/IP), and then click Properties. 5.
Log In to the Modem Router Chapter 4: Log In to the Modem Router Use the web-based utility to configure your Modem Router. Note the following default settings before accessing the web-based utility. SSID TRENDnet658 Channel Auto 802.11 Mode 802.11 b+g+n mixed mode Security Disable IP Address 192.168.10.1 VPI/VCI for ATM 8/35 DSL Line Mode Auto-detect TCP/IP Address 192.168.10.x (where x is a number between 2 (PC) and 254) Default IP Address (Modem 192.168.10.1 Router) Subnet Mask 255.255.255.
Log In to the Modem Router TRENDnet DSLR-2001N 21
Log In to the Modem Router 4.1 Setup Wizard After you log in, the Setup Wizard appears on the screen. It is recommended to follow the wizard if are setting up the network and configuring the Modem Router for the first time. 1. Select a PVC (Permanent Virtual Circuit), then click Next. It is recommended to use the default setting, PVC0, when setting up the Modem Router for the first time. 2. The information required on the page below can be obtained from your Internet service provider (ISP).
Log In to the Modem Router 3. Select a network protocol. Click Next to continue. The information required on the next page vary depending on the network protocol you selected here. 4. The following is a PPPoE example. a. Enter the connection Name, User Name, and User Password. Re-type the password in the Confirm Password field. b. Select whether to enable or disable features such as NAT (Network Address Translation), DNS (Domain Name System), and DNS Override. c.
Log In to the Modem Router 5. Select whether to enable or disable wireless connection. From this point, you can also change the SSID with a name that you can easily remember. Click Next to continue. 6. Select the Security Mode, Authentication Type, and Encryption, and enter a passkey. Click Next to continue. The screen below varies depending on the security mode you selected, below is an example of a WEP security screen. 7. When prompted to reboot, click OK. 8.
Setup Chapter 5: Setup The Setup menu allows you to configure the Internet connection of your Modem Router manually. 5.1 Internet Setup The Internet Setup page is divided into three sections: Internet Connection Settings, Internet Settings, and Protocol. To access the Internet Setup page, click SETUP > Internet Setup. Internet Connection Settings This setting configures the Modem Router to your Internet connection. The required settings should be obtained from your ISP.
Setup PPPoE PassThrough — Select whether to enable or disable PPPoE passthrough. Internet Settings DSL lines use different network protocols to establish Internet connection.
Setup State of Connection — Select whether to enable or disable this connection. IPMode of Connection — Select the connection mode, options are: • • Dynamic: Select Dynamic if the IP address can be automatically obtained from your ISP. Static: Select Static if you are required to use a permanent IP address to connect to the Internet. You must enter the IP Address and Subnet Mask provided by your ISP. Name — Enter your desired connection name.
Setup DNS Server 1 and DNS Server 2 — If provided by your ISP, enter the DNS server. Otherwise, leave these fields blank. PPPoE Service Name — Enter a PPPoE service name. MAC Address — Displays the cloned MAC address. Click the Clone Mac button to clone the MAC address of your computer. PPPoE AC Name — Enter the PPPoE account name provided by your ISP. Connection Trigger — You can configure how you want your Modem Router to connect and terminate the Internet connection.
Setup State of Connection — Select whether to enable or disable this connection. IPMode of Connection — Select the connection mode, options are: • • Dynamic: Select Dynamic if the IP address can be automatically obtained from your ISP. Static: Select Static if you are required to use a permanent IP address to connect to the Internet. You must enter the IP Address and Subnet Mask provided by your ISP. Name — Enter your desired connection name.
Setup Connection Trigger — You can configure how you want your Modem Router to connect and terminate the Internet connection. Options are: • • • OnDemand: Enables the Modem Router to cut off the Internet connection after being idle for a specified period of time. The Modem Router automatically re-establishes the connection when you try to access the Internet again.
Setup IPoA (RFC-1483 Routed) If you select IPoA (IP over ATM), the screen below is displayed. State of Connection — Select whether to enable or disable this connection. Name — Enter your desired connection name. NAT — Select whether to enable or disable NAT (Network Address Translation). Enable this setting to share one WAN IP address with multiple computers on your network. External IP Address — Enter the IP address provided by your ISP. Subnet Mask — Enter the subnet mask provided by your ISP.
Setup Dynamic IP Address If you select Dynamic IP Address, the screen below is displayed. State of Connection — Select whether to enable or disable this connection. Name — Enter your desired connection name. NAT — Select whether to enable or disable NAT (Network Address Translation). Enable this setting to share one WAN IP address with multiple computers on your network. DNS Enabled — Select whether to enable or disable DNS (Domain Name System).
Setup Click the Apply button to save your changes or click the Cancel button to discard your changes.
Setup Static IP Address If you select Static IP Address, the screen below is displayed. State of Connection — Select whether to enable or disable this connection. Name — Enter your desired connection name. NAT — Select whether to enable or disable NAT (Network Address Translation). Enable this setting to share one WAN IP address with multiple computers on your network. External IP Address — Enter the IP address provided by your ISP. Subnet Mask — Enter the subnet mask provided by your ISP.
Setup Bridge Mode If you select Bridge mode (RFC-1483 Bridged), the screen below is displayed. State of Connection — Select whether to enable or disable this connection. Name — Enter your desired connection name. CIP (RFC-1577) If you select CIP (RFC-1577 Classic RP/ARP over ATM), the screen below is displayed. State of Connection — Select whether to enable or disable this connection. Name — Enter your desired connection name. NAT — Select whether to enable or disable NAT (Network Address Translation).
Setup As system default route — Check this box to set the current setting as the default route. ICMP Reply Enable — Check this box to enable ICMP (Internet Control Message Protocol) messages to be sent back to the host that sent the message. Proxy ARP Enable — Check this box to enable proxy ARP function. Click the Apply button to save your changes or click the Cancel button to discard your changes. 5.2 Wireless Settings The Wireless Settings page allows you to enable and configure wireless connections.
Setup network. Wireless Mode — Select the wireless mode to limit the type of wireless devices that can connect to the network. Options are: • • • • 802.11b only: Only 802.11b wireless devices can connect to the network. 802.11g + 802.11b: Only 802.11g and 802.11b wireless devices can connect to the network. 802.11g only: Only 802.11g wireless devices can connect to the network. 802.11n + 802.11g + 802.11b: All 802.11n, 802.11g, and 802.11b wireless devices can connect to the network.
Setup • Auto: Select Auto if you are unsure which authentication is suitable for your wireless devices. • Open System — Open System allows public access to the Modem Router via wireless communications. • Shared Key — Requires users to enter the same WEP key to exchange data with other wireless devices. Encryption Strength — Select 64bit to enter or generate a 10character key or select 128bit to enter or generate a 26-character key.
Setup • Radius Server Key: Enter the passphrase that matches the authentication server. Encryption Type — Displays the encryption type you selected. Group Rekey Time — Enter the number of seconds to elapse until the Modem Router prompts for the key again. Click the Apply button to save your changes or click the Cancel button to discard your changes.
Setup WPA2 (AES) Select WPA (Wi-Fi Protected Access) using AES (Advanced Encryption Standard) for better encryption. Authentication Type — Select an authentication type. Options are: • PSK: Select to use a passphrase for authentication. If you select PSK, enter a passphrase in the Confirmed Passphrase field. • EAP — Select to use Extensible Authentication Protocol (EAP). This should only be used when a Radius server is connected to your Modem Router.
Setup • EAP: Select to use Extensible Authentication Protocol (EAP). This should only be used when a Radius server is connected to your Modem Router. If you select EAP, enter the following information: • • • Radius Server IP: The IP address of the authentication server. Radius Server Port: The port number used to connect to the authentication server. Radius Server Key: Enter the passphrase that matches the authentication server. Encryption Type — Displays the encryption type you selected.
Setup DHCP Setting This section allows you to configure your Modem Router to use the Dynamic Host Configuration Protocol (DHCP). You can set your Modem Router as a DHCP server or a DHCP relay agent of your network. The information required on the DHCP Setting screen vary depending on the selected DHCP option. DHCP Option — Select the DHCP mode of your Modem Router.
Setup IPRouters — Enter the IP address of your Modem Router. The default value is 192.168.10.1. Primary DNS Server and Secondary DNS Server — Enter a primary and a secondary DNS server if the DNS Relay option is enabled. Lease Time — Enter the lease time in seconds. The lease time is the amount of time a device is allowed connection to your Modem Router using its current dynamic IP address. At the end of the lease time, the lease is either renewed or a new IP address is assigned.
Setup Enable — Check this box to enable this function. Host Name — Enter a host name for the DHCP reserved address. IP Address — Enter the IP address to reserve. MAC Address — Enter the MAC address of the device to reserve the IP address to. Click the Apply button to save your changes or click the Cancel button to discard your changes. 5.4 Time and Date The Time and Date page allows you to manually configure the time and date of your network or to synchronize with a Network Time Protocol (NTP) server.
Setup • • • • Server 1 IP or Domain name: Enter the IP address or the domain name of the NTP server to synchronize your network with. Server 2 IP or Domain name: Enter the IP address or the domain name of another NTP server to synchronize your network with in case Server 1 is not available. First Poll Frequency: Enter the number in seconds of the first poll. ThereAfter Frequency: Select the succeeding frequency from the drop-down list.
Advanced Chapter 6: Advanced The Advanced menu configurations greatly affect the operating performance of your Modem Router. This menu is intended for advance users. It is recommended to retain the default settings if you are unsure about them. 6.1 Advanced Wireless Wireless Router Settings This page allows you to configure advanced wireless router settings. Click Advanced > Advanced Wireless > Advanced Wireless or click the Advanced Setting button.
Advanced default and recommended value is 2346 bytes. If you experience a high packet error rate, you may slightly adjust the value. Setting the fragment threshold too low may result in poor network performance. RTS Threshold — The default and recommended value is 2347. Should you encounter inconsistent data flow, only slight modifications should be made. Beacon Interval — Enter a value in milliseconds. A beacon is a packet that is sent out by the Modem Router to synchronize the wireless network.
Advanced Wireless MAC Filter This page allows you to deny or allow devices to access the wireless network by filtering their MAC addresses. Click Advanced > Advanced Wireless > Wireless MAC Filter or click the MAC Filter button. Name (SSID) — Select the SSID from the drop-down list. To Set MAC Filter Do the following to deny or allow a device to access to the wireless network. 1. Select the MAC Restrict Mode. Options are: • • • Disable: No restriction. Deny: To deny access to the wireless network.
Advanced WPS Setting Wi-Fi Protected Setup (WPS) is designed to make wireless setup easy and yet secure. Users do not need to know the network SSID and passphrases to use WPS to join the wireless network. This page allows you to enable WPS-supported devices to connect to your Modem Router. ☞ NOTE: This feature is available only in WPA-PSK, WPA2PSK, or OPEN mode. Click Advanced > Advanced Wireless > WPS Setting or click the WPS Setting button.
Advanced • 6.2 Client PIN: Enter the WPS-supported device’s PIN. This PIN is used to connect to your Modem Router. Click the Add button to apply the configuration. Multi-WAN DSL Auto Scan This page allows you to scan your DSL line for available VPI/VCI. To access the DSL Auto Scan page, click Advanced > Multi-WAN > DSL Auto Scan or click the DSL Auto Scan button. VPI/VCI Scanning Click the Scan button to start scanning your DSL line for available VPI/VCI. Scanning may take several minutes.
Advanced IP/PPP Config This page allows you to create multiple Wide Are Networks (WAN) and manually add an IP or a PPP connection. To access the IP/PPP Config page, click Advanced > Multi-WAN > IP/PPP Config or click the WAN Config button. To add an IP or PPP connection, do the following: 1. Click the Add button of the connection that you want to add. 2. On the Interface field, select the PVC. 3. Enter the connection settings.
Advanced 6.3 Advanced-LAN This page allows you to add multiple LAN IP addresses. To access the Advanced-LAN page, click Advanced > Advanced-LAN. Config Spanning Tree Spanning Tree Enable — Check this box to enable spanning tree. Click the Apply button to save your changes or click the Cancel button to discard your changes. Add IP Interface To add an IP interface, do the following: 1. On the first record on the table, enter the IP Address and Subnet Mask. 2.
Advanced Check a corresponding box to select the option. To reset the ADSL settings, click the Reset button. Click the Apply button to save your changes or click the Cancel button to discard your changes. 6.5 RIP Settings A Routing Information Protocol (RIP) is an Internet protocol that is used to share routing information table with other routing devices on the local and wide area network. To access the RIP Settings page, click Advanced > RIP Settings. To add RIP settings, do the following: 1.
Advanced 6.6 NAT Virtual Server A virtual server allows remote devices accessing the Web or FTP services via a public IP address be redirected to local servers in the LAN. Depending on the requested service (TCP/UDP port number), your Modem Router redirects the external service request to the appropriate server in the LAN. To access the Virtual Server page, click Advanced > NAT > Virtual Server or click the Virtual Server button. The table displays the virtual servers on your network. To edit an icon.
Advanced IP Address — Enter the local network IP address of the system hosting the server. Time Schedule — Select a schedule when to use the virtual server or click the New Time Schedule button to create a new schedule. Click the Apply button to save your changes or click the Cancel button to discard your changes. Port Trigger This page displays the port trigger settings on your network.
Advanced Click the Apply button to save your changes or click the Cancel button to discard your changes. ALG Application Layer Gateway (ALG) consists of a security component that augments NAT or a firewall. Your Modem Router allows NATs to support address and port translation for certain application layer protocols such as FTP, SNMP, and others. To access the ALG page, click Advanced > NAT > ALG or click the ALG Setting button.
Advanced Click the Apply button to save your changes or click the Cancel button to discard your changes.
Advanced VPN Passthrough This page allows you to control VPN tunnels using IPSEC, PPTP, and L2TP protocols to pass through your Modem Router. To access the VPN Passthrough page, click Advanced > NAT > VPN Passthrough or click the VPN Setting button. IPSEC Passthrough — Internet Protocol Security (IPSec) is a protocol suite used to secure IP communications by authenticating and encrypting IP packets. Check this box to enable this function to work through your Modem Router.
Advanced 6.7 Firewall MAC Filter This page allows you to set up a list of MAC addresses which will be allowed or restricted to access the Internet. To access the MAC Filter page, click ADVANCED > Firewall > MAC Filter or click the MAC Filter button. MAC Address Control — Check this box to enable the MAC filter function. Control Action — Select Allow to allow a specified MAC address to access the Internet or Deny to restrict a specified MAC address access to the Internet.
Advanced IP Filter This page allows you to create filter rules to control outgoing traffic to the Internet based on a range of IP addresses and their protocols. To access the IP Filter page, click ADVANCED > Firewall > IP Filter or click the IP Filter button. The table lists the existing filter rules. To edit an entry, click the corresponding icon. To delete an entry, click the corresponding button. To add a filter, click the Add button. The IP Filter Config screen is displayed.
Advanced Time Schedule — Select the time to implement the IP filter or click the New Time Schedule button to create a new schedule. Click the Apply button to save and activate the filter or click the Cancel button to discard your changes. URL Filter This page allows you to deny network devices to access specific URLs or URLs that contain specific keywords. To access the URL Filter page, click ADVANCED > Firewall > URL Filter or click the URL Filter button.
Advanced 1. On the Add Keyword Rule field, enter a keyword. If a part of the URL contains this keyword, the website will not be accessible. 2. Select the time to implement the URL filter or click the New Time Schedule button to create a new schedule. 3. Click the Add button of the Add Keyword Rule. The entry is listed on the URL LIST table. To delete an entry, click the corresponding button. DOS Protection This page allows you to protect your network from hackers to run Denial of Service (DoS) attacks.
Advanced Dos Protection Option — Check the appropriate boxes to enable protection from SYN flood, FIN flood, UDP flood, ICMP flood, SMURF, IP spoofing, and others. Enter the flood count numbers or retain the default values if you are unsure about them. Check the Apply button to save and activate DoS protection or click the Cancel button to discard your changes. Domain Blocking This page allows you to deny network devices to access specific domains such as an http and an ftp.
Advanced DMZ — Check this box to enable DMZ. DSL Interface — Select the DSL interface to activate DMZ from the drop-down list. DMZ Host IP Address — Enter the IP address of the computer to set as the DMZ host. Check the Apply button to save and activate DMZ. SPI Settings SPI (Stateful Packet Inspection) filters more kinds of attacks by closely examining packet data structures. To access the SPI Settings page, click ADVANCED > Firewall > SPI Settings or click the SPI Settings button.
Advanced 6.8 Packet Filter Filters & Rules This page allows you to create packet filters and rules. These filters are used to check each data that passes within your network. If the packet data does not meet the requirements, the packet is either dropped or rejected. To access the Filters & Rules page, click ADVANCED > Packet Filter > Filters & Rules or click the Filters & Rules button. Filters Click the Add button to create a new filter. Name — Enter desired filter name.
Advanced Rules After creating filters, click the Add button to set the rules on how to implement the filters. Filter Key — Select the filter to assign the rule. Enable — Check this box to enable this rule. Protocol — Select a protocol from the drop-down list. Options are TCP, UDP, or ICMP. Action — Select the action to execute when the rule requirement is met. Options are: • • • Drop: Select to drop the packets if the rule requirement is met.
Advanced Destination Start Port and Destination End Port — Enter the starting and ending port range of the destination of the packets. ICMP Type — Select an ICMP type from the drop-down list. If the selected type is met, the filter is implemented. Click the Apply button to save and activate the rule or click the Cancel button to discard your changes. Statistics This page displays the filter and rule statistics.
Advanced Click the Apply button to save and activate the static route or click the button to discard your changes.
Advanced 6.10 Multicast Internet Group Management Protocol (IGMP) manages members of groups of devices, called IP multicast groups. IGMP is used by IP hosts and adjacent multicast routers to establish multicast group membership. It is an integral part of the IP multicast specification, like ICMP for unicast connections. IGMP is used for online video and gaming, and allows more efficient use of resources that support these applications. To access the Multicast page, click ADVANCED > Multicast.
Advanced Response Interval, and Group Live Delay Time. If you are unsure about them, leave the default values. IGMP Snooping With IGMP snooping, your Modem Router can make intelligent multicast forwarding to connections that have group members attached. As a result, IGMP snooping prevents or reduces traffic on the interface that is not registered as a receiver of a specific multicast group. Select IGMP Proxy Version.
Advanced Use Dynamic DNS Service — Check this box to register this account to the DNS server. Service Provider — Select a service provider from the drop-down list. ☞ NOTE: Additional charges may be incurred depending on the selected service provider. Host Name — Enter a domain name to be registered to the DNS server. User Name — Enter the user name of your DNS account assigned by the service provider. Password — Enter the password of your DNS account assigned by the service provider.
Advanced 6.13 Port Mapping Port mapping allows you to group interfaces for traffic control. Traffic is isolated from group to group. Therefore, traffic coming from an interface of a group can only be flowed to the interfaces in the same group. By default, all interfaces belong to the Default group. You can create new groups and move interfaces to other groups. However, an interface can only be a member of one group. To access the Port Mapping page, click ADVANCED > Port Mapping.
Advanced 3. Click the Apply button to save your changes. To Delete Groups Click the corresponding Delete button of the group to delete. The members of that group automatically revert back to the Default group.
Advanced 6.14 Quality of Service (QoS) Quality of Service (QoS) is a network standard that assigns the priorities of traffic that passes through your Modem Router. This ensures that demanding real-time applications, such as video streaming, are given priority over other data. Queue Management This page allows you to enable QoS and choose Differentiated Services Code Point (DSCP) markings to automatically mark incoming traffic without reference to a particular classifier.
Advanced The table displays QoS queue configurations. To edit an entry, click the corresponding icon. To delete an entry, click the corresponding icon. To configure QoS queue entries, click the Add button. Name — Enter a QoS queue entry name. Enable — Check this box to enable this queue. Interface — Select the interface to implement this QoS queue. Policy — Select the queue policy. Options are: • • SP: In Strict Priority (SP), packets with a high priority are processed first.
Advanced Queue Classification This page allows you to configure classification rules to classify upstream traffic and assign queues which define the precedence, interface, and optionally overwrite the IP header DSCP byte. A rule consists of a class name and at least one condition. All the specified conditions in the classification rule must be satisfied for the rule to take effect.
Advanced Class Name — Enter a class name. Class Enable — Check this box to enable the class. Specify Classification Criteria You can classify traffic based on ingress interface, Ether type, packet length, source or destination MAC address/ MAC Mask, or a combination of them. Select an option or enter the values on the fields that you want to use for the criteria. Otherwise, leave the fields empty. Depending on the selected Ether Type, the succeeding required information may vary.
Advanced If packet length is used as a criteria, select the Packet Length Rule from the drop-down list and enter the Packet Length. Specify Classification Results Some fields may not be applicable; if so, leave inapplicable fields empty. Assign Classification Queue — Select the classification queue from the drop-down list. Only enabled classification queues from the Queue Classification page are listed here.
Advanced 6.15 UPnP Universal Plug and Play (UPnP) allows automatic discovery and control of services available on the network from other devices without user intervention. This feature is commonly used for gaming and video streaming. If you feel that UPnP is a security concern, disable this feature. To access the UPnP page, click ADVANCED > UPnP. UPnP — Check this box to enable the UPnP feature. UPnP LOG — Check this box to log UPnP status. TR064 — Check this box to enable TR064.
Advanced 6.16 SNMP Simplified Network Management Protocol (SNMP) is a troubleshooting and management protocol that is used to monitor the status and change the configurations of your Modem Router locally or remotely. It also allows configuring and receiving of trap messages from network devices that are configured for SNMP. To access the SNMP page, click ADVANCED > SNMP. SNMP — Check this box to enable SNMP. System Contact — Enter the contact person or contact information for your Modem Router.
Maintenance Chapter 7: Maintenance The Maintenance menu allows you to configure the web-based utility settings, such as password, remote management, backup/restore options, firmware upgrades, and others. 7.1 Password By default, the log in user name and password are “admin”. For security reasons, it is strongly recommended to change the password. To access the Password page, click MAINTENANCE > Password. User Name — Select the user account: admin or user. Current Password — Enter the current password.
Maintenance 7.2 Remote Management This page allows you to enable remote devices to manage your Modem Router using the Hypertext Transfer Protocol (HTTP), Command-Line Interface (CLI), and File Transfer Protocol Daemon (FTPD). To access the Remote Management page, click MAINTENANCE > Remote Management. HTTP Management Check the Http Enable box to allow network administrators to remotely access the web-based utility via WAN interface.
Maintenance FTPD Management Check the FTPD Enable box to allow network administrators to upgrade the firmware or restore configurations using the FTP. Keep old session — Check to retain the old session. Click the Apply button to save your changes or click the Cancel button to discard your changes. 7.3 Remote Access This page allows you to create and edit remote access rules.
Maintenance Wan Interface — Select the interface from the drop-down list. Status — Select whether to enable or disable remote access of the device. Remote IP — Enter the IP address of the remote device. Remote IP Mask — Enter the IP mask of the remote device. ☞ NOTE: To allow or deny all devices to remotely access your Modem Router, enter “*” on the Remote IP and Remote IP Mask fields. Service — Select the type of remote management service that the device can or cannot access.
Maintenance TR069 Settings Enable — Check this box to enable TR069. Use Interface — Select the interface to implement TR069. ACS URL Address — Enter the URL of the Auto-Configuration Server (ACS) ACS User Name — Enter the user name of your Modem Router when connecting to the ACS. ACS Password — Enter the password that your Modem Router should use when connecting to the ACS. Re-enter the password on the Confirm Password field. Connection Request Port —Enter the port that issues the request.
Maintenance Periodic Inform — When enabled, your Modem Router will send remote procedure calls (RPC) to the ACS server at system startup and will continue sending RPCs periodically. When disabled, your Modem Router will send RPCs to the ACS server at system startup only. Periodic Inform Interval — Enter the interval time of sending RPCs. TR069 CA IMPORT To import certificates, do the following: 1. Click the Browse button. 2. Browse for the certificate, then click the Open button. 3.
Maintenance 7.5 Init Script This page allows you to show, delete, and import initialization scripts running on customer-premises equipment (CPE), such as telephones, routers, or set-top boxes, during system startup or shutdown. To access the Init Script page, click MAINTENANCE > Init Script. Init start scripts are scripts that run before the system starts up. Init end scripts are scripts that run before the system shuts down. To import scripts, do the following: 1. Click the Browse button. 2.
Maintenance 7.6 SysLog This page allows you to enable and configure system logs such as device status, events, and activities. Logs can be sent to the network administrator via e-mail. To access the SysLog page, click MAINTENANCE > SysLog. Log Generate Enable Options Kernel Common Message — Check this box to generate logs. Click the Apply button to save and apply the setting. Log Rules Setting The table displays current log rules. To edit an entry, click the corresponding icon.
Maintenance 3. Select Location: Remote Server or Mail. 4. The succeeding fields may vary depending on the selected location. Enter the necessary information accordingly. 5. Click the Apply button to save your changes or click the Cancel button to discard your changes. E-mail Log Periodically To log e-mails periodically, do the following: 1. Check the SMTP Server box to enable logging of e-mails periodically. 2. Enter the SMTP Server IP, Source E-mail Address, and Destination E-mail Address. 3.
Maintenance 7.7 Time Schedule This page allows you create desired time schedule. To access the Time Schedule page, click MAINTENANCE > Time Schedule. To create a new schedule, do the following: 1. On the Name field, enter desired schedule name. 2. Check the days to implement the schedule and select the time period. 3. Click the Add button to save the schedule. The new entry is listed on the TIME SCHEDULE LIST. To delete a schedule, click the corresponding 7.8 icon.
Maintenance ☞ NOTE: Do not turn off or press the Reset button on your Modem Router while firmware upgrade is in progress. This may cause the system to crash.
Maintenance 7.9 Configuration Backup/Restore This page allows you to save a backup of your current settings, revert settings to a backup point, or restore the default factory settings. To access the Configuration Backup/Restore page, click MAINTENANCE > Configuration Backup/Restore. To backup the current settings, click the Backup Settings button. To restore settings from a backup point, do the following: 1. Click the Browse button. 2. Browse for the backup file, and then click the Open button. 3.
Maintenance 7.10 Ping Once you have configured your Modem Router, it is recommended to ping the network devices to verify their connection. When you execute a ping test, a series of packets are sent to a specific computer. When the computer receives the packets, it will respond with an acknowledgment that it received the packets. To access the Ping page, click MAINTENANCE > Ping. Host IP Address — Enter the IP address of the network device that you want to ping. Click the Ping button to start ping.
Maintenance 7.11 Diagnostics This page allows you to test the connectivity of the physical and protocol layers on the WAN side. To access the Diagnostics page, click MAINTENANCE > Diagnostics. To start the test, select the DSL Interface from the drop-down list, and then click the Test button. 7.12 Reboot Device In the event that your device does not respond correctly or stops responding, reset your device. All your settings will be retained. 1. Click the Reset button. 2. Click OK to confirm. 3.
Status Chapter 8: Status The Status menu provides the current status and settings of your Modem Router. 8.1 Summary This page displays the summary of the system, DSL link, ATM PVC, Internet connection, LAN, and wireless ports status. To access the Summary page, click STATUS > Summary. 8.2 ADSL Info This page displays the status of your DSL line. To access the ADSL Info page, click STATUS > ADSL Info. Click the Refresh button to refresh the information.
Status 8.3 Wireless Clients This page displays the clients connected on your network via wireless connection. To access the Wireless Clients page, click STATUS > Wireless Clients. Click the Refresh button to refresh the information. 8.4 LAN Clients This page displays the clients connected on your network. To access the LAN Clients page, click STATUS > LAN Clients. Click the Refresh button to refresh the information.
Status 8.5 Logs This page allows you to view, clear, and backup system logs. To access the Logs page, click STATUS > Logs. You can filter the list by selecting a particular Facility, Severity, Module, or History from the drop-down lists. Click the Clear History button to delete old logs. Click the Backup Logs button to save a backup of the logs. Click the |< << >> >| buttons to scroll through the logs. Click the Refresh button to refresh the information.
Status 8.6 Routing Table This page displays the destination routes commonly accessed by your network. To access the Routing Table page, click STATUS > Routing Tables. Click the Refresh button to refresh the information. 8.7 Traffic Meter This page displays the transmission and reception statistics of packets that pass through the specified interface. To access the Traffic Meter page, click STATUS > Traffic Meter. Traffic Data Interface The table lists the available interfaces on your network.
Status Traffic Bandwidth Interval Interval — Enter the interval of refreshing the traffic bandwidth. Traffic Bandwidth Meter This table lists the current traffic. 8.8 Driver Version This page displays the current kernel, Wi-Fi, and DSL driver versions. To access the Driver Version page, click STATUS > Driver Version. 8.9 Statistics Basic Statistics This page displays the transmission and reception statistics of the Internet connection, LAN device, wireless port, and the LAN ports.
Status Statistics > DSL Statistics This page displays the transmission and reception statistics of the DSL line. To access the DSL Statistics page, click STATUS > Statistics > DSL Statistics or click the DSL Statistics button. Click the Refresh button to refresh the information.
Appendix Appendix A. Regulatory & Safety Information Wireless LAN, Health and Authorization Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions however are far much less than the electromagnetic energy emissions from wireless devices like for example mobile phones. Wireless LAN devices are safe for use frequency safety standards and recommendations.
Appendix FCC (Federal Communications Commission) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Appendix TRENDnet DSLR-2001N 103
Appendix PART 68 statement This equipment complies with Part 68 of FCC Rules and the requirements adopted by the ACTA.. On the bass unit of this equipment is a label that contains, among other information, a product identifier in the format US: CAMDL02BDSLR2001N . If requested, this number must be provided to the telephone company. The REN for this product is part of the product identifier that has the format US: CAMDL02BDSLR2001N . The digits represented by 01 are the REN without a decimal point.
Appendix CE statement Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.
Appendix TRENDnet DSLR-2001N 106
Appendix Česky [Czech] TRENDnet tímto prohlašuje, že tento DSLR-2001N je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede TRENDnet erklærer herved, at følgende udstyr DSLR-2001N overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Appendix [Slovak] Suomi [Finnish] Svenska [Swedish] všetky príslušné ustanovenia Smernice 1999/5/ES. TRENDnet vakuuttaa täten että DSLR-2001N tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Härmed intygar TRENDnet att denna DSLR-2001N står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Appendix B. Specifications General Compliant with ADSL standards: ANSI T1.413 Issue2, G.992.1 (G.dmt, Annex A), G.992.2 (G.lite) Compliant with ADSL2 standard: G.992.3 (G.dmt.bis) Standards Compliant with ADSL2+ standard: G.992.5 Annex A IEEE 802.11b & 802.11g & 802.11n Wireless LAN IEEE 802.
Appendix Security 64/128-bits WEP Encryption; WPA, WPA2, WPA-TKIP, WPA2-AES, WPS, MAC address filtering Firewall Security NAT firewall, Stateful Packet Inspection (SPI), Packet Filtering (IP, MAC Domain, Keyword), Management Access Control for LAN/WAN Management Web-based Configuration, Command Line Interface (CLI) via Telnet, TR-069 Remote Management, IGMP v1/v2 Support, SW upgrade USA : Channel 1~11 Channels Europe : Channel 1~13 Japan : Channel 1 ~14 FLASH: 4MB Memory DDR SDRAM: 32MB Antenna 2
Appendix C. Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. DSLR-2001N – 3 Years Warranty AC/DC Power Adapter, Cooling Fan, and Power Supply carry 1 year warranty.
Appendix EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TRENDNET NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION MAINTENANCE OR USE OF TRENDNET’S PRODUCTS.
