DSLR-2000N 802.
Regulatory notes and statements Wireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions however are far much less than the electromagnetic energy emissions from wireless devices like for example mobile phones. Wireless LAN devices are safe for use frequency safety standards and recommendations.
PART 68 statement This equipment complies with Part 68 of FCC Rules and the requirements adopted by the ACTA.. On the bass unit of this equipment is a label that contains, among other information, a product identifier in the format US: CAMDL01BDSLR2000N. If requested, this number must be provided to the telephone company. The REN for this product is part of the product identifier that has the format US: CAMDL01BDSLR2000N. The digits represented by 01 are the REN without a decimal point.
This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France. Česky [Czech] [Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
v
TABLE OF CONTENT ABOUT THIS GUIDE ....................................................................................1 Purpose.................................................................................................................................................................................................. 1 Terms/Usage ................................................................................................................................................................................
Port Forwarding .............................................................................................................................................................................. 43 URL Blocking................................................................................................................................................................................. 45 Domain Blocking .............................................................................................................
ABOUT THIS GUIDE Congratulations on your purchase of this 300Mbps Wireless G 2/2+ ADSL Modem Router. This integrated access device combines ADSL modem, Internet gateway functions with wireless LAN and Fast Ethernet switch. It provides a complete solution for Internet surfing and office resource sharing, and it is easy to configure and operate for every user. Purpose This manual discusses how to install the IEEE 300Mbps Wireless N 2/2+ ADSL Modem Router.
INTRODUCTION The 300Mbps Wireless N ADSL 2/2+ Modem Router is an all-in-one modem and wireless g router. No need to buy a separate modem and router. This sleek device provides an ADSL 2/2+ modem, wireless g router and 4-port switch, all in a single product. Quickly install this device to surf the Internet, download files, play games and talk Online. Advanced wireless encryption, a double firewall and a wireless on/off switch protect your valuable data.
Wireless Performance Considerations There are a number of factors that can impact the range of wireless devices. 1. Adjust your wireless devices so that the signal is traveling in a straight path, rather than at an angle. The more material the signal has to pass through the more signal you will lose. 2. Keep the number of obstructions to a minimum. Each obstruction can reduce the range of a wireless device. Position the wireless devices in a manner that will minimize the amount of obstructions between them.
UNPACKING AND SETUP This chapter provides unpacking and setup information for the 300Mbps Wireless N 2/2+ ADSL Modem Router. Unpacking Open the box of the WLAN ADSL Router and carefully unpack it. The box should contain the following items: 300Mbps Wireless N 2/2+ ADSL Modem Router CD-Rom (User’s Guide) External power adapter 1 1.5m (5ft) Cat.5 Ethernet Cable 1 RJ-11 (ADSL) cable If any item is found missing or damaged, please contact your local reseller for replacement.
HARDWARE INSTALLATION Front Panel The figure below shows the front panel of the IEEE 802.11b/g/n Wireless ADSL Router. Front Panel LED Indicators LED Power Color Green State Solid on Red Solid on Off DSL Green Green Internet LAN 1~4 Red Off Green Blinking Solid on Blinking Solid on Solid on Blinking Solid on Off WLAN Green Off Blinking Solid on Description Power on, normal operation. Power on, self-test failed, indicating device malfunction. Power off. Pending ADSL line synchronization.
Green WPS Red Off Blinking WPS in progress. Solid on Solid on WPS success. WPS fail. WPS disabled.
Rear Panel The figure below shows the rear panel of the IEEE 802.11b/g/n Wireless ADSL Router. Rear Panel Antenna One 2dBi gain antenna for wireless connection. LAN (1-4) Four RJ-45 10/100Mbps Auto-MDIX ports for connecting to either 10Mbps or 100Mbps Ethernet connections. DSL (ADSL Port) Connect to an active telephone line (RJ-11). DC IN Receptor for the supplied power adapter. ON/OFF (On/Off Switch) Press this button to turn the unit on or off. WPS Button Press to enable Wi-Fi Protected Setup.
Hardware connections Connecting the WLAN ADSL Router 1. Connect ADSL Cable Connect the supplied RJ-11 ADSL cable from to the DSL port on the Wireless ADSL Router (the RJ11 connector) to the ADSL terminator provided by your phone company. 2. Connect LAN Cables Use standard LAN cables to connect PCs to the LAN ports on the Wireless ADSL Router. 3. Connect Power Connect the supplied power adapter to the Wireless ADSL Router. Use only the power adapter provided. Using a different one may cause hardware damage.
PC NETWORK TCP/IP SETTING The network TCP/IP settings differ based on the computer’s operating system (Win95/98/ME/NT/2000/XP/Vista) and are as follows. Windows 95/98/ME 1. Click on the “Network neighborhood” icon found on the desktop. 2. Click the right mouse button and a context menu will be show. 3. Select “Properties” to enter the TCP/IP setting screen. 4. Select “Obtain an IP address automatically” on the “IP address” field. 5. Select “Disable DNS” in the “DNS” field.
6. Select “None” for the “Gateway address” field. Windows 2000 Double click on the “My Computer” icon on the desktop. When “My Computer” window opens, open the “Control Panel” and then open the “Network dialup connection” applet. Double click on the “Local area network connection” icon. Select “Properties” to enter the TCP/IP setting window. 1. In the “Local area network status” window, click on “Properties.” 2.
Windows XP / Vista Point the cursor and click the right button on the “My Network Place” icon. Select “properties” to enter the TCP/IP setting window. 1. Set “IP address” to “Obtain an IP address automatically.” 2. Set “DNS” to “Obtain DNS server address automatically.
CONFIGURATION First make sure that the network connections are functioning normally. This WLAN Router can be configured using Internet Explorer 5.0 or newer web browser versions. Login to the WLAN ADSL Router through Wireless LAN Before configuring the WLAN ADSL Router through WLAN, make sure that the SSID, Channel and the WEP is set properly. The default setting of the WLAN ADSL Router that you will use: SSID: ADSL_Modem/Router Channel: Auto 802.11 Mode: 802.
3. When the following dialog box appears, enter the user name and password to login to the main configuration window, the default username and password is “admin”. After entering the user name and password, the main page comes up, the screen will display the SETUP WIZARD status.
Configuration Menu When the main page appears, find the Configuration menu in the left side of the screen. Click on the setup item that you want to configure. There are ten options: Setup Wizard, Status, Setup, Firewall (form router mode only), Advance (form router mode only), Maintenance, Diagnostic, Monitoring, Mode and Reboot as shown in the Configuration Menu screen.
SETUP WIZARD Setup wizard is provided as part of the web configuration utility. User can simply follow the step-by-step process to get the WLAN ADSL Router configuration ready by clicking on` the “Wizard” button on the function menu. The following screen will appear. Step 1: Determine Connection Method Choose “Auto-detect” for auto detect the Internet connection method or “Manual Selection” for manually configure the ADSL setting.
Step 2: ADSL Setting VPI: Enter the VPI value provided by ISP VCI: Enter the VCI value provided by ISP Encapsulation: Select the encapsulation type for LLC or VC-Mux ADSL modulation: Select the ADSL modulation type defined by your ISP Step 3: Select Channel Mode Select the type of network protocol for 1483 Bridged, 1483 MER, PPPoE, PPPoA or 1483 Routed.
1483 Bridged Selected the 1483 Bridged mode then click next button, the WLAN ADSL Router will save configuration and reboot the WLAN ADSL Router. When rebooted the WLAN ADSL Router, enabled the “Test Internet Connection” then click finish button for test Internet connection; click close button close the setup wizard.
1483 MER Selected the 1483 MER mode then click next button, continuing the WAN IP setting. Select whether user wants to specify an IP address manually, or want DHCP to obtain an IP address automatically.
If selected to 1483 MER mode with DHCP, the follows step will going on: Click next button to save configuration and reboot the WLAN ADSL Router When rebooted the WLAN ADSL Router, enabled the “Test Internet Connection” then click finish button for test Internet connection; click close button close the setup wizard.
If selected to 1483 MER mode with Fixed IP, the follows step will going on: Enter the Local IP Address, Gateway IP Address, Subnet Mask and Wan MAC (if need to specify the other Wan MAC address) in the text boxes, click next button to continue the DNS server setting.
When rebooted the WLAN ADSL Router, enabled the “Test Internet Connection” then click finish button for test Internet connection; click close button close the setup wizard. PPPoE/PPPoA Selected the PPPoE or PPPoA mode then click next button, continue the account setting. User Name: Enter the username provided by ISP. Password: Enter the password provided by ISP Type: Select the connection type for Continuous Connecting, Connect on Demand or Manual connecting.
Click next button to save configuration and reboot the WLAN ADSL Router 22
When rebooted the WLAN ADSL Router, enabled the “Test Internet Connection” then click finish button for test Internet connection; click close button close the setup wizard. 1483 Routed Selected the 1483 Routed mode then click next button, continuing the WAN IP setting. NAPT: Checked to enable the NAPT on the WLAN ADSL Router.
Setting the DNS server assigned by DHCP or manually, click next button to save configuration and reboot the WLAN ADSL Router.
1577 Routed Selected the 1577 Routed mode then click next button, continuing the WAN IP setting. Select whether user wants to specify an IP address manually, or want DHCP to obtain an IP address automatically.
If selected to 1577 Routed mode with DHCP, the follows step will going on: Click next button to save configuration and reboot the WLAN ADSL Router When rebooted the WLAN ADSL Router, enabled the “Test Internet Connection” then click finish button for test Internet connection; click close button close the setup wizard.
If selected to 1577 Routed mode with Fixed IP, the follows step will going on: Enter the Local IP Address, Gateway IP Address, Subnet Mask and Wan MAC (if need to specify the other Wan MAC address) in the text boxes, click next button to continue the DNS server setting.
Step 4: Completed the Setup Wizard When rebooted the WLAN ADSL Router, enabled the “Test Internet Connection” then click finish button for test Internet connection; click close button close the setup wizard.
MANUAL SETINGS Find that there are ten items, including Setup Wizard, Status, Setup, Firewall (form router mode only), Advance (form router mode only), Maintenance, Diagnostic, Monitoring, Mode and Reboot in Setup menu. Status This page displays the WLAN ADSL Router current status and settings. Click the “Refresh” button to update the status. Setup The section enables users to configure the Internet (ADSL), LAN, Wireless, DHCP and Time Zone setting.
VPI: Virtual Path Identifier. Enter the VPI value provided by ISP. VCI: Virtual Channel Identifier. Ethernet the VCI value provided by ISP. Encapsulation: Select the encapsulation type LLC or VC-Mux produced by your ISP. Channel Mode: Select the channel mode for 1483 Bridged, 1483 MER, PPPoE, PPPoA, 1483 Routed or 1577 Routed provide by ISP. Enable NAPT: Checked to enable the NAPT function on the WLAN ADSL Router. Admin Status: Enable or disable the ATM VC setting when adding to the ATM VC Table.
Type: Select the connection type for “Continuous”, “Connect on Daemon” or “Manual” connect. Idle Time: Enter the idle time for Connect on Daemon, when no Internet access during the idle time, the ADSL connection will auto disconnect. WAN IP Settings: Type: Select whether user wants to specify an IP address manually, or want DHCP to obtain an IP address automatically. When Fixed IP is selected, type the Local IP Address, Gateway IP Address and Subnet Mask in the text boxes.
IP Address: This is the IP address of the router. The default IP address is 192.168.1.1. Subnet Mask: Type the subnet mask for the router in the text box. The default subnet mask is 255.255.255.0. Secondary IP: Checked to enable the secondary IP address setting on the LAN. IP Address: The secondary IP address setting of the LAN. Subnet Mask: The secondary Subnet Mask setting of the LAN. IGMP Snooping: Enable/disable the IGMP snooping function for the multiple bridged LAN ports.
Basic Settings This page allow user to enable and disable the wireless LAN function, create a SSID, and select the channel for wireless communications. Disable: Checked to disable the wireless function of the WLAN ADSL Router. Band: Select one of the following: 2.4Ghz (B+G) - Selected if you are allowing both 802.11b and 802.11g wireless clients connect to the WLAN ADSL Router at the same time. 2.4Ghz (B) - Selected if you are allowing the 802.11b wireless clients connect to the WLAN ADSL Router only. 2.
Associated Clients: Click the “Show Active Client” button displays the information of connected wireless clients. Security SSID TYPE: The WLAN ADSL Router supports up to four multiple SSID feature (Multiple Virtual AP), select which AP (Root AP, VAP0~VAP3) will configure the security setting. Encryption: There are 4 types of security to be selected. To secure your WLAN, it’s strongly recommended to enable this feature.
802.1x Authentication: Checked to enable the 802.1x authentication. This option is selectable only when the “Encryption” is selected to either None or WEP. If the “Encryption” is WEP, you need to further select the WEP key length to be either WEP 64bits or WEP 128bits. WEP: Click the “Set WEP Key” button to setting WEP key when the “Encryption” is selected to “WEP”.
Pre-Shared Key Format: Passphrase: Select this to enter the Pre-Shared Key secret as user-friendly textual secret. Hex (64 characters): Select this to enter the Pre-Shared Key secret as hexadecimal secret. Pre-Shared Key: Specify the shared secret used by this Pre-Shared Key. If the “Pre-Shared Key Format” is specified as Passphrase, then it indicates a passphrase of 8 to 63 bytes long; or if the “Pre-Shared Key Format” is specified as Passphrase, then it indicates a 64-hexadecimal number.
Disable WPS: Checked to disable the Wi-Fi protected Setup. WPS Status: When the WLAN ADSL Router settings are factory default (out of box), it is set to open security and un-configured state. “WPS Status” will display it as “UnConfigured”. If it already shows “Configured”, some registrars such as Vista WCN will not configure AP. Users will need to go to the “Backup/Restore” page and click “Reset” to reload factory default settings. Self-PIN Number: The “Self-PIN Number” is AP’s PIN.
DHCP Settings You can configure your WLAN ADSL Router to use the Dynamic Host Configuration Protocol (DHCP). This section provides DHCP instructions for implementing it on your network by selecting the role of DHCP protocol that this device wants to play. DHCP Mode: There are two different DHCP roles that this device can act as: DHCP Server and DHCP Relay.
IP Pool Range: Specify the lowest and highest addresses in the pool. Subnet Mask: Specify the subnet mask value. Max Lease Time: The Lease Time is the amount of time that a network user is allowed to maintain a network connection to the device using the current dynamic IP address. At the end of the Lease Time, the lease is either renewed or a new IP is issued by the DHCP server. The amount of time is in units of seconds. The default value is 86400 seconds (1 day). The value –1 stands for the infinite lease.
MAC-Base Assignment: Click the “MAC-Base Assignment” button to configure the static IP base on MAC Address. You can assign/delete the static IP. The Host MAC Address, please input a string with hex number. Such as "00-d059-c6-12-43". The Assigned IP Address, please input a string with digit. Such as "192.168.10.100". Click “Assign IP” button to add the static DHCP setting to the MAC-Base Assignment Table.
Enable SNTP client update: Enable the SNTP client to update the system clock. SNTP server: The IP address or the host name of the SNTP server. You can select from the list or set it manually. Daylight Saving: Checked to enable daylight saving time. When enabled, select the start and end date for daylight saving time. Firewall – Used only on Router mode settings The Firewall setting is for the WLAN ADSL Router is configured on Router mode only. Please refer the Mode setting in page 79.
Add/Modify Rule Add or modify the IP/Port filtering rule. Direction: Select the traffic forwarding direction “Outgoing” or “Incoming”. Protocol: Select the protocol type for TCP, UDP or ICMP. Rule Action: Deny or allow traffic when matching this rule. Source: The source IP address, Subnet Mask and Port range assigned to the traffic on which filtering is applied. Destination: The destination IP address, Subnet Mask and Port range assigned to the traffic on which filtering is applied.
Add/Modify Rule Add or modify the MAC filtering rule. Rule Action: Deny or allow traffic when matching this rule. Source: The source MAC address. It must be xxxxxxxxxxxx format. Blanks can be used in the MAC address space and are considered as don’t care. Add: Click the “Add” button to save the rule entry to the configuration. Modify: Click the “Modify” button to modify the selected rule form the Current MAC Filter Table.
Add/Modify Rule Add or modify the Port Forwarding rule. Protocol: Select the protocol type for TCP, UDP or Both (TCP and UTP). Enable: Check to enable this rule. Interface: Select the WAN interface on which the port-forwarding rule is to be applied. Local: The local IP address and Port range assigned to the traffic on which filtering is applied. Destination: The remote IP address and Port range assigned to the traffic on which filtering is applied.
URL Blocking The URL Blocking is the web filtering solution. The firewall includes the ability to block access to specific web URLs based on string matches. This can allow large numbers of URLs to be blocked by specifying only a FQDN (such as tw.yahoo.com). The URL Blocking enforce a Web usage policy to control content downloaded from, and uploaded to, the Web. URL Blocking: Select to enable or disable the URL blocking feature. Add FQDN Rule Rule Action: Deny or allow traffic when matching this rule.
Add Keyword Rule Rule Action: Deny or allow traffic when matching this rule. Keyword: The filtered keyword such as yahoo. If the URL includes this keyword, the URL will be blocked to access. Add: Click the “Add” button to save the rule entry to the configuration. Delete Selected: Click the “Delete Selected” button to delete the selected rule from Keyword Filtering Table. Delete All: Click the “Delete All” button to delete the all of rule in the Keyword Filtering Table.
Add Rule Rule Action: Deny or allow traffic when matching this rule. Domain: Enter the blocked domain. Add: Click the “Add” button to save the rule entry to the configuration. Delete Selected: Click the “Delete Selected” button to delete the selected rule from Domain Block Table. Delete All: Click the “Delete All” button to delete the all of rule in the Domain Blocking Table.
Related Protocol: Select the incoming protocol type for TCP, UDP or TCP&UTP. Related port range: Enter the incoming port range that can be used to access the application in the text boxes. Add: Click the “Add” button to save the rule entry to the configuration. Modify: Click the “Modify” button to modify the selected rule form the Trigger Table. Delete Selected: Click the “Delete Selected” button to delete the selected rule from Trigger Table.
Advance – Used only on Router mode settings The Advance setting is for the WLAN ADSL Router is configured on Router mode only. Please refer the Mode setting in page 79. Wireless Advanced Settings These settings are only for more technically advanced users who have a sufficient knowledge about wireless LAN. These settings should not be changed unless you know what effect the changes will have on your WLAN ADSL Router.
Fragment Threshold: This value should remain at its default setting of 2000. It specifies the maximum size for a packet before data is fragmented into multiple packets. If you experience a high packet error rate, you may slightly increases the “Fragment Threshold” value within the value range of 256 to 2346. Setting this value too low may result in poor network performance. Only minor modifications of this value are recommended. The default is 2346.
Relay Blocking: Select to enable or disable the Relay Blocking feature. When Relay Blocking is enabled, wireless clients will not be able to directly access other wireless clients. WMM support: Select to enable or disable the WMM (Wi-FI Multimedia) QoS feature. Access Control This feature allows administrator to have access control by enter MAC address of client stations.
MBSSID The WLAN ADSL Router supports up to four virtual AP (Vap0~Vap3) setting allows wireless users connect up to the WLAN ADSL Router through up to four different WLAN SSID and security settings. Enable: Enable or disable the Vap (Virtual AP) setting. SSID: Type an SSID in the text box. The SSID of any wireless device must match the SSID typed here in order for the wireless device to access the LAN and WAN via the WLAN ADSL Router.
Ethernet Isolation: Select to enable or disable the Ethernet Isolation feature. When Ethernet Isolation is enabled, wireless clients will not be able to access to the Ethernet clients. Dynamic DNS Each time your device connects to the Internet, your ISP assigns a different IP address to your device. In order for you or other users to access your device from the WAN-side, you need to manually track the IP that is currently used.
Bridging This page is used to configure the bridge parameters. Here you can change the settings or view some information on the bridge and its attached ports. Aging Time: Set the Ethernet address ageing time, in seconds. After [Ageing Time] seconds of not having seen a frame coming from a certain address, the bridge will time out (delete) that address from Forwarding DataBase (fdb). Show MACs: Click the “Show MACs” button to list MAC address in forwarding DataBase(fdb).
Routing The Routing page enables you to define specific route for your Internet and network data. Most users do not need to define routes. On a typical small home or office LAN, the existing routes that set up the default gateways for your LAN hosts and for the WLAN ADSL Router provide the most appropriate path for all your Internet traffic. On your LAN hosts, a default gateway directs all Internet traffic to the LAN port(s) on the WLAN ADSL Router.
Subnet Mask: The network mask of the destination subnet. The default gateway uses a mask of 0.0.0.0. Next Hop: The IP address of the next hop through which traffic will flow towards the destination subnet. Metric: Defines the number of hops between network nodes that data packets travel. The default value is 0, which means that the subnet is directly one hop away on the local LAN network. Interface: The WAN interface to which a static routing subnet is to be applied.
IGMP Proxy IGMP proxy enables the system to issue IGMP host messages on behalf of hosts that the system discovered through standard IGMP interfaces. The system acts as a proxy for its hosts when you enable it by doing the follows: Enable IGMP proxy on WAN interface (upstream), which connects to a router running IGMP. Enable IGMP on LAN interface (downstream), which connects to its hosts. IGMP Proxy: Select to enable or disable the IGMP proxy feature on the WLAN ADSL Router.
UPnP: Select to enable or disable the UPnP feature on the WLAN ADSL Router. WAN Interface: Select WAN interface that will use UPnP from the drop-down lists. RIP Enable the RIP if you are using this device as a RIP-enabled router to communicate with others using the Routing Information Protocol. This page is used to select the interfaces on your device is that use RIP, and the version of the protocol used.
RIP: Select to enable or disable the RIP feature on the WLAN ADSL Router. Receive Mode: Select which RIP version to be used for RIP listening, RIP1, RIP2 or Both (RIP1+RIP2), Selected None to disable the RIP listening. Send Mode: Select which RIP version to be used for RIP sending, RIP1, RIP2 or Both (RIP1+RIP2), Selected None to disable the RIP sending. Delete Selected: Click the “Delete Selected” button to delete the selected RIP config from RIP Config Table.
Community name: Read-only: Name of the read-only community. This read-only community allows read operation to all objects in the MIB. Write-only: Name of the write-only community. This write-only community allows write operation to the objects defines as read-writable in the MIB. Port Mapping The WLAN ADSL Router provides multiple interface groups. Up to five interface groups are supported including one default group. The LAN and WAN interfaces could be included.
IP QoS The WLAN ADSL Router provides a control mechanism that can provide different priority to different users or data flows. The QoS is enforced by the QoS rules in the QoS table. A QoS rule contains two configuration blocks: Traffic Classification and Action. The Traffic Classification enables you to classify packets on the basis of various fields in the packet and perhaps the physical ingress port.
workable on a given PVC channel only if the VLAN tag is enabled in this PVC channel. Precedence: Select this field to mark the IP precedence bits in the packet that match this classification rule. TOS: Select this field to mark the IP TOS bits in the packet that match this classification rule. Add: Click to add the QoS rule to the UP QoS Rules. Delete Selected: Click the “Delete Selected” button to delete the selected QoS rule from the IP QoS Rules.
ATM Settings This page is used to configure the parameters for the ATM of your ADSL Router. Here you may change the setting for VPI, VCI, QoS etc. VPI: Virtual Path Identifier. This is read-only field and is selected on the Select column in the Current ATM VC Table. VCI: Virtual Channel Identifier. This is read-only field and is selected on the Select column in the Current ATM VC Table. The VCI, together with VPI, is used to identify the next destination of a cell as it passes through to the ATM switch.
CDVT: Cell Delay Variation Tolerance, is a QoS parameter in ATM network for managing traffic that is specified when a connection is set up. In CBR transmissions, CDVT determines the level of jitter that is tolerable for the data samples taken by the PCR. SCR: Sustained Cell Rate, measured in cells/sec., is the average cell rate over the duration of the connection. MBS: Maximum Burst Size, a traffic parameter that specifies the maximum number of cells that can be transmitted at the peak cell rate.
ADSL modulation: Choose preferred xDSL standard protocols, defined by ISP. G.lite: G.992.2 Annex A G.dmt: G.992.1 Annex A T1.413: T1.413 issue #2 ADSL2: G.992.3 Annex A ADSL2+: G.992.5 Annex A AnnexL Option: Checked to Enable the ADSL2/ADSL2+ Annex L capability. AnnexM Option: Checked to Enable the ADSL2/ADSL2+ Annex M capability. ADSL Capability: Checked to enable the bitswap capability or SRA capability. ADSL Tone: Click the “ADSL Tone” button to choose tones to be masked.
Maintainance Backup/Restore This page allows you to backup current settings to a file or restore the settings from the file which was saved previously. Besides, you could reset the current configuration to factory default. Save Setting to File: Click the “Save Setting to File” button to save current settings of the WLAN ADSL Router to local computer.
User Name: Selection of user levels are: admin and user. Old Password: Enter the old password for this selected login. New Password: Enter the new password here. Confirmed Password: Enter the new password here again to confirm.
Upgrade Firmware This page allows you to upgrade the WLAN ADSL Router firmware. Please note, do not power off the device during the upgrade process. It may crash the system. To upgrade the firmware for the DSL device: Click the Browse button to select the firmware file. Confirm your selection. Click the Upload button to start upgrading. IMPORTANT! Do not turn off your DSL device or click the Reset button while this procedure is in progress.
Access Controls The Access Control List (ACL) is a list of permissions attached to the WLAN ADSL Router. The list specifies who is allowed to access this device. If ACL is enabled, all hosts cannot access this device except for the hosts with IP address in the ACL table. ACL Capability: Enable or Disable the SNMP feature on the WLAN ADSL Router. Enable: Checked to enable the selected route or route to be added. Interface: Select the interface domain: LAN or WAN.
TR-069 Config TR-069 is a protocol for communication between a CPE and Auto-Configuration Server (ACS). The CPE TR-069 configuration should be well defined to be able to communicate with the remote ACS. TR069: Enable or Disable the TR-069 feature on the WLAN ADSL Router. ACS URL: Enter the ACS URL here. User Name: The username the WLAN ADSL Router should use when connecting to the ACS. Password: The password the WLAN ADSL Router should use when connecting to the ACS.
Connection Request User Name: The username the remote ACS should use when connecting to this device. Password: The password the remote ACS should use when connecting to this device. Path: The path of the device ConnectionRequestURL. The device ConnectionRequestURL should be configured based on the Device_IP, Path and Port as follows: http://Device_IP:Port/Path. Port: The port of the device ConnectionRequestURL. Logout This page is used to logout from ADSL gateway.
Diagnostic Ping Once you have your WLAN ADSL Router configured, it is a good idea to make sure you can ping the network. A ping command sends a message to the host you specify. If the host receives the message, it sends messages in reply. To use it, you must know the IP address of the host you are trying to communicate with and enter the IP address in the Host Address field. Click “Go” button to start the ping command, the ping result will then be shown in this page.
ATM Loopback In order to isolate the ATM interface problems, you can use ATM OAM loopback cells to verify connectivity between VP/VC endpoints, as well as segment endpoints within the VP/VC. ATM uses F4 and F5 cell flows as follows: F4: used in VPs. F5: used in VCs. An ATM connection consists of a group of points. This OAM implementation provides management for the following points: Connection endpoint: the end of a VP/VC connection where the ATM cell are terminated.
ADSL This page shows the ADSL diagnostic result. Click “Start” button to start the ADSL diagnostic. Diagnostic Test The Diagnostic Test page shows the test results for the connectivity of the physical layer and protocol layer for both LAN and WAN sides. Select Internet Connection: The available WAN side interfaces are listed. You have to select one for the WAN side diagnostic.
Run Diagnostic Test: Click the “Run Diagnostic Test” button to start the diagnostic test.
Monitoring DHCP Clients This table shows the assigned IP address, MAC address and time expired for each DHCP leased client. Routing Table This table shows a list of destination routes commonly accessed by your network.
ARP Table This table shows a list of learned MAC addresses. Bridge FDB Table This table shows a list of learned MAC addresses for this bridge.
Interface Statistics This page shows the packet statistics for transmission and reception regarding to network interface. ADSL Statistics This page shows the packet statistics for transmission and reception regarding to the ADSL.
Mode This page explains configuration and operation when in "Router" or "Modem" mode. Device Mode: There are two modes available on the Mode screen. Router: Both the ADSL Modem and the Router features are operational. In this mode, this device can provide shared Internet Access to all your LAN users. Also, by default, it acts a DHCP Server, providing an IP address and related information to all Wireless and LAN users. Modem: Only the ADSL Modem component is operational.
Reboot Click "Commit and Reboot" button to apply setting changes and to reboot the WLAN ADSL Router.
TECHNICAL SPECIFICATIONS General Standards Protocol Radio Technology Data Transfer Rate Receiver Sensitivity TX Power Network Cables Frequency Range Modulation Schemes Security Management Compliant with ADSL standards: ANSI T1.413 Issue2, G.992.1 (G.dmt, Annex A), G.992.2 (G.lite) Compliant with ADSL2 standard: G.992.3 (G.dmt.bis) Compliant with ADSL2+ standard: G.992.5 Annex A IEEE 802.11b & 802.11g Wireless LAN IEEE 802.
Channels Number of Ports 1~11 Channels (FCC) 1~13 Channels (ETSI) LAN: 4 x 10/100Mbps Auto-MDIX Fast Ethernet port WAN: 1 x RJ11Port 82
Physical and Environmental DC inputs 12VDC 1A Power Consumption 7.
