MBSSID The WLAN ADSL Router supports up to four virtual AP (Vap0~Vap3) setting allows wireless users connect up to the WLAN ADSL Router through up to four different WLAN SSID and security settings. Enable: Enable or disable the Vap (Virtual AP) setting. SSID: Type an SSID in the text box. The SSID of any wireless device must match the SSID typed here in order for the wireless device to access the LAN and WAN via the WLAN ADSL Router.
Wireless Isolation: Select to enable or disable the Wireless Isolation feature. When Wireless Isolation is enabled, wireless clients will not be able to access to the other wireless clients. Ethernet Isolation: Select to enable or disable the Ethernet Isolation feature. When Ethernet Isolation is enabled, wireless clients will not be able to access to the Ethernet clients. DNS Server This page is used to select the way to obtain the IP addresses of the DNS servers.
Dynamic DNS Each time your device connects to the Internet, your ISP assigns a different IP address to your device. In order for you or other users to access your device from the WAN-side, you need to manually track the IP that is currently used. The Dynamic DNS feature allows you to register your device with a DNS server and access your device each time using the same host name. The Dynamic DNS page allows you to enable/disable the Dynamic DNS feature.
Bridging This page is used to configure the bridge parameters. Here you can change the settings or view some information on the bridge and its attached ports. Aging Time: Set the Ethernet address ageing time, in seconds. After [Ageing Time] seconds of not having seen a frame coming from a certain address, the bridge will time out (delete) that address from Forwarding DataBase (fdb). Show MACs: Click the “Show MACs” button to list MAC address in forwarding DataBase(fdb).
Routing The Routing page enables you to define specific route for your Internet and network data. Most users do not need to define routes. On a typical small home or office LAN, the existing routes that set up the default gateways for your LAN hosts and for the WLAN ADSL Router provide the most appropriate path for all your Internet traffic. On your LAN hosts, a default gateway directs all Internet traffic to the LAN port(s) on the WLAN ADSL Router.
Subnet Mask: The network mask of the destination subnet. The default gateway uses a mask of 0.0.0.0. Next Hop: The IP address of the next hop through which traffic will flow towards the destination subnet. Metric: Defines the number of hops between network nodes that data packets travel. The default value is 0, which means that the subnet is directly one hop away on the local LAN network. Interface: The WAN interface to which a static routing subnet is to be applied.
IGMP Proxy IGMP proxy enables the system to issue IGMP host messages on behalf of hosts that the system discovered through standard IGMP interfaces. The system acts as a proxy for its hosts when you enable it by doing the follows: Enable IGMP proxy on WAN interface (upstream), which connects to a router running IGMP. Enable IGMP on LAN interface (downstream), which connects to its hosts. IGMP Proxy: Select to enable or disable the IGMP proxy feature on the WLAN ADSL Router.
UPnP: Select to enable or disable the UPnP feature on the WLAN ADSL Router. WAN Interface: Select WAN interface that will use UPnP from the drop-down lists. RIP Enable the RIP if you are using this device as a RIP-enabled router to communicate with others using the Routing Information Protocol. This page is used to select the interfaces on your device is that use RIP, and the version of the protocol used.
RIP: Select to enable or disable the RIP feature on the WLAN ADSL Router. Receive Mode: Select which RIP version to be used for RIP listening, RIP1, RIP2 or Both (RIP1+RIP2), Selected None to disable the RIP listening. Send Mode: Select which RIP version to be used for RIP sending, RIP1, RIP2 or Both (RIP1+RIP2), Selected None to disable the RIP sending. Delete Selected: Click the “Delete Selected” button to delete the selected RIP config from RIP Config Table.
Trap IP Address: Destination IP address of the SNMP trap. Community name: Read-only: Name of the read-only community. This read-only community allows read operation to all objects in the MIB. Write-only: Name of the write-only community. This write-only community allows write operation to the objects defines as read-writable in the MIB. Port Mapping The WLAN ADSL Router provides multiple interface groups. Up to five interface groups are supported including one default group.
IP QoS The WLAN ADSL Router provides a control mechanism that can provide different priority to different users or data flows. The QoS is enforced by the QoS rules in the QoS table. A QoS rule contains two configuration blocks: Traffic Classification and Action. The Traffic Classification enables you to classify packets on the basis of various fields in the packet and perhaps the physical ingress port.
Outbound Priority: The priority level for the traffic that matches this classification rule. The possible selections are (in the descending priority): p0, p1, p2, p3. 802.1p: Select this field to mark the 3-bit user-priority field in the 802.1p header of the packet that match this classification rule. Note that this 802.1p marking is workable on a given PVC channel only if the VLAN tag is enabled in this PVC channel.
WAN Port: This field allows the user to specify the port of the corresponding service. Take the HTTP service for example; when it is changed to 8080, the HTTP server address for the WAN side is http://dsl_addr:8080, where the dsl_addr is the WAN side IP address of the WLAN ADSL Router. ATM Settings This page is used to configure the parameters for the ATM of your ADSL Router. Here you may change the setting for VPI, VCI, QoS etc. VPI: Virtual Path Identifier.
rt-VBR (real-time Variable Bit Rate): When rt-VBR is selected, the SCR and MBS fields are enabled. PCR: Peak Cell Rate, measured in cells/sec., is the cell rate which the source may never exceed. CDVT: Cell Delay Variation Tolerance, is a QoS parameter in ATM network for managing traffic that is specified when a connection is set up. In CBR transmissions, CDVT determines the level of jitter that is tolerable for the data samples taken by the PCR. SCR: Sustained Cell Rate, measured in cells/sec.
ADSL modulation: Choose preferred xDSL standard protocols, defined by ISP. G.lite: G.992.2 Annex A G.dmt: G.992.1 Annex A T1.413: T1.413 issue #2 ADSL2: G.992.3 Annex A ADSL2+: G.992.5 Annex A AnnexL Option: Checked to Enable the ADSL2/ADSL2+ Annex L capability. AnnexM Option: Checked to Enable the ADSL2/ADSL2+ Annex M capability. ADSL Capability: Checked to enable the bitswap capability or SRA capability. ADSL Tone: Click the “ADSL Tone” button to choose tones to be masked.
Maintainance Backup/Restore This page allows you to backup current settings to a file or restore the settings from the file which was saved previously. Besides, you could reset the current configuration to factory default. Save Setting to File: Click the “Save Setting to File” button to save current settings of the WLAN ADSL Router to local computer.
User Name: Selection of user levels are: admin and user. Old Password: Enter the old password for this selected login. New Password: Enter the new password here. Confirmed Password: Enter the new password here again to confirm.
Upgrade Firmware This page allows you to upgrade the WLAN ADSL Router firmware. Please note, do not power off the device during the upgrade process. It may crash the system. To upgrade the firmware for the DSL device: Click the Browse button to select the firmware file. Confirm your selection. Click the Upload button to start upgrading. IMPORTANT! Do not turn off your DSL device or click the Reset button while this procedure is in progress.
Access Controls The Access Control List (ACL) is a list of permissions attached to the WLAN ADSL Router. The list specifies who is allowed to access this device. If ACL is enabled, all hosts cannot access this device except for the hosts with IP address in the ACL table. ACL Capability: Enable or Disable the SNMP feature on the WLAN ADSL Router. Enable: Checked to enable the selected route or route to be added. Interface: Select the interface domain: LAN or WAN.
TR-069 Config TR-069 is a protocol for communication between a CPE and Auto-Configuration Server (ACS). The CPE TR-069 configuration should be well defined to be able to communicate with the remote ACS. TR069: Enable or Disable the TR-069 feature on the WLAN ADSL Router. ACS URL: Enter the ACS URL here. User Name: The username the WLAN ADSL Router should use when connecting to the ACS. Password: The password the WLAN ADSL Router should use when connecting to the ACS.
Connection Request User Name: The username the remote ACS should use when connecting to this device. Password: The password the remote ACS should use when connecting to this device. Path: The path of the device ConnectionRequestURL. The device ConnectionRequestURL should be configured based on the Device_IP, Path and Port as follows: http://Device_IP:Port/Path. Port: The port of the device ConnectionRequestURL. Logout This page is used to logout from ADSL gateway.
Go: Click “Go” button to start the ping command, the ping result will then be shown in this page.
ATM Loopback In order to isolate the ATM interface problems, you can use ATM OAM loopback cells to verify connectivity between VP/VC endpoints, as well as segment endpoints within the VP/VC. ATM uses F4 and F5 cell flows as follows: F4: used in VPs. F5: used in VCs. An ATM connection consists of a group of points. This OAM implementation provides management for the following points: Connection endpoint: the end of a VP/VC connection where the ATM cell are terminated.
ADSL This page shows the ADSL diagnostic result. Click “Start” button to start the ADSL diagnostic.
Diagnostic Test The Diagnostic Test page shows the test results for the connectivity of the physical layer and protocol layer for both LAN and WAN sides. Select Internet Connection: The available WAN side interfaces are listed. You have to select one for the WAN side diagnostic. Run Diagnostic Test: Click the “Run Diagnostic Test” button to start the diagnostic test.
Monitoring DHCP Clients This table shows the assigned IP address, MAC address and time expired for each DHCP leased client. Routing Table This table shows a list of destination routes commonly accessed by your network.
ARP Table This table shows a list of learned MAC addresses. Bridge FDB Table This table shows a list of learned MAC addresses for this bridge.
Interface Statistics This page shows the packet statistics for transmission and reception regarding to network interface. ADSL Statistics This page shows the packet statistics for transmission and reception regarding to the ADSL.
Mode This page explains configuration and operation when in "Router" or "Modem" mode. Device Mode: There are two modes available on the Mode screen. Router: Both the ADSL Modem and the Router features are operational. In this mode, this device can provide shared Internet Access to all your LAN users. Also, by default, it acts a DHCP Server, providing an IP address and related information to all Wireless and LAN users. Modem: Only the ADSL Modem component is operational.
Reboot Click "Commit and Reboot" button to apply setting changes and to reboot the WLAN ADSL Router.
TECHNICAL SPECIFICATIONS General Standards Protocol Radio Technology Data Transfer Rate Receiver Sensitivity TX Power (Average power) Network Cables Frequency Range Modulation Schemes Security Management Channels Number of Ports Compliant with ADSL standards: ANSI T1.413 Issue2, G.992.1 (G.dmt, Annex A), G.992.2 (G.lite) Compliant with ADSL2 standard: G.992.3 (G.dmt.bis) Compliant with ADSL2+ standard: G.992.5 Annex A IEEE 802.11b & 802.11g Wireless LAN IEEE 802.
Physical and Environmental DC inputs 12VDC 1A Power Consumption 6.
