DSLR-2000G 802.
Regulatory notes and statements Wireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions however are far much less than the electromagnetic energy emissions from wireless devices like for example mobile phones. Wireless LAN devices are safe for use frequency safety standards and recommendations.
PART 68 statement This equipment complies with Part 68 of FCC Rules and the requirements adopted by the ACTA.. On the bass unit of this equipment is a label that contains, among other information, a product identifier in the format US: CAMDL01BDSLR2000G. If requested, this number must be provided to the telephone company. The REN for this product is part of the product identifier that has the format US: CAMDL01BDSLR2000G. The digits represented by 01 are the REN without a decimal point.
This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France. Česky [Czech] [Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
TABLE OF CONTENT ABOUT THIS GUIDE ....................................................................................1 Purpose.................................................................................................................................................................................................. 1 Terms/Usage ................................................................................................................................................................................
URL Blocking................................................................................................................................................................................. 37 Domain Blocking ............................................................................................................................................................................ 38 Port Triggering................................................................................................................
ABOUT THIS GUIDE Congratulations on your purchase of this IEEE 802.11b/g Wireless ADSL Router. This integrated access device combines ADSL modem, Internet gateway functions with wireless LAN and Fast Ethernet switch. It provides a complete solution for Internet surfing and office resource sharing, and it is easy to configure and operate for every user. Purpose This manual discusses how to install the IEEE 802.11b/g Wireless ADSL Router.
INTRODUCTION The wireless router is a high-speed ADSL2+ Ethernet/Wireless router that is specifically designed to connect to the Internet and to directly connect to your local area network (LAN) via high-speed 10/100 Mbps Ethernet, or wireless LAN (WLAN). The ADSL2+ modem is compatible with the latest ADSL standards, including ADSL2 and ADSL2+, and supports up to 24 Mbps downstream and 1.5 Mbps upstream to deliver true broadband speed and throughput. The DSL router supports wireless 802.
Auto-detection of Internet Connection Method. In most situations, the Wireless ADSL Router can test your ADSL and Internet connection to determine the connection method used by ISP Supports ADSL standards for ITU-T G.992.1(G.dmt), ANSI T1.413 Issue 2, G.992.2 (G.lite), ADSL2 G.dmt.bis (G.992.3), ADSL2+ (G.992.5) Wi-Fi compliant with IEEE 802.11g and IEEE 802.
UNPACKING AND SETUP This chapter provides unpacking and setup information for the IEEE 802.11b/g Wireless ADSL Router. Unpacking Open the box of the WLAN ADSL Router and carefully unpack it. The box should contain the following items: TEW-436BRM Wireless ADSL Router CD-Rom (User’s Guide) External power adapter 1 1.5m (5ft) Cat.5 Ethernet Cable 1 RJ-11 (ADSL) cable If any item is found missing or damaged, please contact your local reseller for replacement.
HARDWARE INSTALLATION Front Panel The figure below shows the front panel of the IEEE 802.11b/g Wireless ADSL Router. Front Panel LED Indicators LED Power Color Green State Solid on Red Solid on Off DSL Green Green Internet LAN 1~4 Red Off Green Blinking Solid on Blinking Solid on Solid on Blinking Solid on Off WLAN Green Blinking Solid on Off Green WPS Red Off Blinking Solid on Solid on Description Power on, normal operation. Power on, self-test failed, indicating device malfunction.
Rear Panel The figure below shows the rear panel of the IEEE 802.11b/g Wireless ADSL Router. Rear Panel Antenna One 2dBi gain antenna for wireless connection. LAN (1-4) Four RJ-45 10/100Mbps Auto-MDIX ports for connecting to either 10Mbps or 100Mbps Ethernet connections. DSL (ADSL Port) Connect to an active telephone line (RJ-11). DC IN Receptor for the supplied power adapter. ON/OFF (On/Off Switch) Press this button to turn the unit on or off. WPS Button Press to enable Wi-Fi Protected Setup.
Hardware connections Connecting the WLAN ADSL Router 1. Connect ADSL Cable Connect the supplied RJ-11 ADSL cable from to the DSL port on the Wireless ADSL Router (the RJ11 connector) to the ADSL terminator provided by your phone company. 2. Connect LAN Cables Use standard LAN cables to connect PCs to the LAN ports on the Wireless ADSL Router. 3. Connect Power Connect the supplied power adapter to the Wireless ADSL Router. Use only the power adapter provided. Using a different one may cause hardware damage.
PC NETWORK TCP/IP SETTING The network TCP/IP settings differ based on the computer’s operating system (Win95/98/ME/NT/2000/XP/Vista) and are as follows. Windows 95/98/ME 1. Click on the “Network neighborhood” icon found on the desktop. 2. Click the right mouse button and a context menu will be show. 3. Select “Properties” to enter the TCP/IP setting screen. 4. Select “Obtain an IP address automatically” on the “IP address” field. 5. Select “Disable DNS” in the “DNS” field.
6. Select “None” for the “Gateway address” field. Windows 2000 Double click on the “My Computer” icon on the desktop. When “My Computer” window opens, open the “Control Panel” and then open the “Network dialup connection” applet. Double click on the “Local area network connection” icon. Select “Properties” to enter the TCP/IP setting window. 1. In the “Local area network status” window, click on “Properties.” 2.
Windows XP / Vista Point the cursor and click the right button on the “My Network Place” icon. Select “properties” to enter the TCP/IP setting window. 1. Set “IP address” to “Obtain an IP address automatically.” 2. Set “DNS” to “Obtain DNS server address automatically.
CONFIGURATION First make sure that the network connections are functioning normally. This WLAN Router can be configured using Internet Explorer 5.0 or newer web browser versions. Login to the WLAN ADSL Router through Wireless LAN Before configuring the WLAN ADSL Router through WLAN, make sure that the SSID, Channel and the WEP is set properly. The default setting of the WLAN ADSL Router that you will use: SSID: TRENDnet436 Channel: Auto 802.11 Mode: 802.
After entering the user name and password, the main page comes up, the screen will display the WLAN ADSL Router status.
Configuration Menu When the main page appears, find the Configuration menu in the left side of the screen. Click on the setup item that you want to configure. There are ten options: Setup Wizard, Status, Setup, Firewall (form router mode only), Advance (form router mode only), Maintenance, Diagnostic, Monitoring, Mode and Reboot as shown in the Configuration Menu screen.
SETUP WIZARD Setup wizard is provided as part of the web configuration utility. User can simply follow the step-by-step process to get the WLAN ADSL Router configuration ready by clicking on` the “Wizard” button on the function menu. The following screen will appear. Step 1: Determine Connection Method Choose “Auto-detect” for auto detect the Internet connection method or “Manual Selection” for manually configure the ADSL setting.
Step 2: ADSL Setting VPI: Enter the VPI value provided by ISP VCI: Enter the VCI value provided by ISP Encapsulation: Select the encapsulation type for LLC or VC-Mux ADSL modulation: Select the ADSL modulation type defined by your ISP Step 3: Select Channel Mode Select the type of network protocol for 1483 Bridged, 1483 MER, PPPoE, PPPoA or 1483 Routed.
1483 Bridged Selected the 1483 Bridged mode then click next button, the WLAN ADSL Router will save configuration and reboot the WLAN ADSL Router. When rebooted the WLAN ADSL Router, enabled the “Test Internet Connection” then click finish button for test Internet connection; click close button close the setup wizard.
1483 MER Selected the 1483 MER mode then click next button, continuing the WAN IP setting. Select whether user wants to specify an IP address manually, or want DHCP to obtain an IP address automatically. When Fixed IP is selected, type the Local IP Address, Remote IP Address and Subnet Mask in the text boxes. User’s ISP will provide with this information.
Click next button to save configuration and reboot the WLAN ADSL Router When rebooted the WLAN ADSL Router, enabled the “Test Internet Connection” then click finish button for test Internet connection; click close button close the setup wizard. PPPoE/PPPoA Selected the PPPoE or PPPoA mode then click next button, continue the account setting.
User Name: Enter the username provided by ISP. Password: Enter the password provided by ISP Type: Select the connection type for Continuous Connecting, Connect on Demand or Manual connecting. Idle Time: Enter the idle time for Connect on Daemon, when no Internet access during the idle time, the ADSL connection will auto disconnect. Default Route: Setting the default router function disable or enable.
When rebooted the WLAN ADSL Router, enabled the “Test Internet Connection” then click finish button for test Internet connection; click close button close the setup wizard. 1483 Routed Selected the 1483 Routed mode then click next button, continuing the WAN IP setting. NAPT: Checked to enable the NAPT on the WLAN ADSL Router.
Click next button to save configuration and reboot the WLAN ADSL Router Step 4: Completed the Setup Wizard When rebooted the WLAN ADSL Router, enabled the “Test Internet Connection” then click finish button for test Internet connection; click close button close the setup wizard.
MANUAL SETINGS Find that there are ten items, including Setup Wizard, Status, Setup, Firewall (form router mode only), Advance (form router mode only), Maintenance, Diagnostic, Monitoring, Mode and Reboot in Setup menu. Status This page displays the WLAN ADSL Router current status and settings. Click the “Refresh” button to update the status. Setup The section enables users to configure the Internet (ADSL), LAN, Wireless, DHCP and Time Zone setting.
VPI: Virtual Path Identifier. Enter the VPI value provided by ISP. VCI: Virtual Channel Identifier. Ethernet the VCI value provided by ISP. Encapsulation: Select the encapsulation type LLC or VC-Mux produced by your ISP. Channel Mode: Select the channel mode for 1483 Bridged, 1483 MER, PPPoE, PPPoA, 1483 Routed or 1577 Routed provide by ISP. Enable NAPT: Checked to enable the NAPT function on the WLAN ADSL Router. Admin Status: Enable or disable the ATM VC setting when adding to the ATM VC Table.
WAN IP Settings: Type: Select whether user wants to specify an IP address manually, or want DHCP to obtain an IP address automatically. When Fixed IP is selected, type the Local IP Address, Remote IP Address and Subnet Mask in the text boxes. User’s ISP will provide with this information. Unnumbered: Checked to enable the IP unnumbered on the WLAN ADSL Router. Default Route: Setting the default router function disable or enable. Add Button: Click add button to add the new VC setting to the ATM VC Table.
Secondary IP: Checked to enable the secondary IP address setting on the LAN. IP Address: The secondary IP address setting of the LAN. Subnet Mask: The secondary Subnet Mask setting of the LAN. Ethernet to Wireless Blocking: When enabled the Ethernet to Wireless Blocking, all of Ethernet users can’t communicate with WLAN users. Wireless This section enables users to configuration the wireless communications parameters for the WLAN ADSL Router.
Channel: Select a transmission channel for wireless communications. The channel of any wireless device must match the channel selected here in order for the wireless device to access the LAN and WAN via the WLAN ADSL Router. Radio Power (mW): The maximum output power for wireless LAN: 15mW, 30mW or 60mW. Associated Clients: Click the “Show Active Client” button displays the information of connected wireless clients.
WAP2 Mixed: The AP supports WPA (TKIP) and WPA2 (AES) for data encryption. The actual selection of the encryption methods will depend on the clients. 802.1x Authentication: Checked to enable the 802.1x authentication. This option is selectable only when the “Encryption” is selected to either None or WEP. If the “Encryption” is WEP, you need to further select the WEP key length to be either WEP 64bits or WEP 128bits.
Personal (Pre-Shared Key): Pre-Shared Key authentication is based on a shared secret that is known only by the parties involved. To use WPA PreShared Key, select key format and enter a password in the “Pre-Shared Key Format” and “Pre-Shared Key” setting respectively. Please refer to “PreShared Key Format” and “Pre-Shared Key” setting below. Pre-Shared Key Format: Passphrase: Select this to enter the Pre-Shared Key secret as user-friendly textual secret.
Disable WPS: Checked to disable the Wi-Fi protected Setup. WPS Status: When the WLAN ADSL Router settings are factory default (out of box), it is set to open security and un-configured state. “WPS Status” will display it as “UnConfigured”. If it already shows “Configured”, some registrars such as Vista WCN will not configure AP. Users will need to go to the “Backup/Restore” page and click “Reset” to reload factory default settings. Self-PIN Number: The “Self-PIN Number” is AP’s PIN.
DHCP Settings You can configure your WLAN ADSL Router to use the Dynamic Host Configuration Protocol (DHCP). This section provides DHCP instructions for implementing it on your network by selecting the role of DHCP protocol that this device wants to play. DHCP Mode: There are two different DHCP roles that this device can act as: DHCP Server and DHCP Relay.
IP Pool Range: Specify the lowest and highest addresses in the pool. Subnet Mask: Specify the subnet mask value. Max Lease Time: The Lease Time is the amount of time that a network user is allowed to maintain a network connection to the device using the current dynamic IP address. At the end of the Lease Time, the lease is either renewed or a new IP is issued by the DHCP server. The amount of time is in units of seconds. The default value is 86400 seconds (1 day). The value –1 stands for the infinite lease.
MAC-Base Assignment: Click the “MAC-Base Assignment” button to configure the static IP base on MAC Address. You can assign/delete the static IP. The Host MAC Address, please input a string with hex number. Such as "00-d059-c6-12-43". The Assigned IP Address, please input a string with digit. Such as "192.168.10.100". Click “Assign IP” button to add the static DHCP setting to the MAC-Base Assignment Table.
Time Zone Select: The time zone in which the WLAN ADSL Router resides. Enable SNTP client update: Enable the SNTP client to update the system clock. SNTP server: The IP address or the host name of the SNTP server. You can select from the list or set it manually. Daylight Saving: Checked to enable daylight saving time. When enabled, select the start and end date for daylight saving time.
Add/Modify Rule Add or modify the IP/Port filtering rule. Direction: Select the traffic forwarding direction “Outgoing” or “Incoming”. Protocol: Select the protocol type for TCP, UDP or ICMP. Rule Action: Deny or allow traffic when matching this rule. Source: The source IP address, Subnet Mask and Port range assigned to the traffic on which filtering is applied. Destination: The destination IP address, Subnet Mask and Port range assigned to the traffic on which filtering is applied.
Add/Modify Rule Add or modify the MAC filtering rule. Rule Action: Deny or allow traffic when matching this rule. Source: The source MAC address. It must be xxxxxxxxxxxx format. Blanks can be used in the MAC address space and are considered as don’t care. Add: Click the “Add” button to save the rule entry to the configuration. Modify: Click the “Modify” button to modify the selected rule form the Current MAC Filter Table.
Add/Modify Rule Add or modify the Port Forwarding rule. Protocol: Select the protocol type for TCP, UDP or Both (TCP and UTP). Enable: Check to enable this rule. Interface: Select the WAN interface on which the port-forwarding rule is to be applied. Local: The local IP address and Port range assigned to the traffic on which filtering is applied. Destination: The remote IP address and Port range assigned to the traffic on which filtering is applied.
URL Blocking The URL Blocking is the web filtering solution. The firewall includes the ability to block access to specific web URLs based on string matches. This can allow large numbers of URLs to be blocked by specifying only a FQDN (such as tw.yahoo.com). The URL Blocking enforce a Web usage policy to control content downloaded from, and uploaded to, the Web. URL Blocking: Select to enable or disable the URL blocking feature. Add FQDN Rule Rule Action: Deny or allow traffic when matching this rule.
Add Keyword Rule Rule Action: Deny or allow traffic when matching this rule. Keyword: The filtered keyword such as yahoo. If the URL includes this keyword, the URL will be blocked to access. Add: Click the “Add” button to save the rule entry to the configuration. Delete Selected: Click the “Delete Selected” button to delete the selected rule from Keyword Filtering Table. Delete All: Click the “Delete All” button to delete the all of rule in the Keyword Filtering Table.
Add Rule Rule Action: Deny or allow traffic when matching this rule. Domain: Enter the blocked domain. Add: Click the “Add” button to save the rule entry to the configuration. Delete Selected: Click the “Delete Selected” button to delete the selected rule from Domain Block Table. Delete All: Click the “Delete All” button to delete the all of rule in the Domain Blocking Table.
Match port range: Enter the outgoing port range that can be used to access the application in the text boxes. Related Protocol: Select the incoming protocol type for TCP, UDP or TCP&UTP. Related port range: Enter the incoming port range that can be used to access the application in the text boxes. Add: Click the “Add” button to save the rule entry to the configuration. Modify: Click the “Modify” button to modify the selected rule form the Trigger Table.
DMZ Host: Select to enable or disable the DMZ feature. DMZ Host IP Address: Enter a IP address of the local host. This feature sets a local host to be exposed to the Internet Advance – Used only on Router mode settings The Advance setting is for the WLAN ADSL Router is configured on Router mode only. Please refer the Mode setting in page 72. Wireless Advanced Settings These settings are only for more technically advanced users who have a sufficient knowledge about wireless LAN.
Fragment Threshold: This value should remain at its default setting of 2000. It specifies the maximum size for a packet before data is fragmented into multiple packets. If you experience a high packet error rate, you may slightly increases the “Fragment Threshold” value within the value range of 256 to 2346. Setting this value too low may result in poor network performance. Only minor modifications of this value are recommended. The default is 2346.
Relay Blocking: Select to enable or disable the Relay Blocking feature. When Relay Blocking is enabled, wireless clients will not be able to directly access other wireless clients. WMM support: Select to enable or disable the WMM (Wi-FI Multimedia) QoS feature. Access Control This feature allows administrator to have access control by enter MAC address of client stations.
